Home » Seagate Manuals » Hard Drives » Seagate STM940215A » Manual Viewer

Seagate STM940215A Maxtor MobileMax PATA Product Manual - Page 15

STM980215A s, Drive specification, STM980215A - hard drive

Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Table 1: STM980215A specifications summary Drive specification Shock, operating Shock, nonoperating Shock, nonoperating Shock, nonoperating Vibration, operating (max displacement may apply below 10 hz) Vibration, nonoperating (max displacement may apply below 22 hz) Drive acoustics, sound power, 2 disc Idle** Performance seek Nonrecoverable read errors Annualized Failure Rate (AFR) Load/Unload (U/UL) cycles STM980215A 250 Gs max at 2 msec 800 Gs max at 2 msec 900 Gs max at 1 msec 400 Gs max at 0.5 msec 1.0 Gs (0 to peak, 5-500 Hz) 5.0 Gs (0 to peak, 5-500 Hz) 2.4 bels (typical) 2.6 bels (max) 2.9 bels (typical) 3.1 bels (max) 1 per 1014 bits read 0.73% 25°C, 50% relative humidity 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 32°C, 80% relative humidity 5°C, 80% relative humidity 5°C, 20% relative humidity 60°C, 20% relative humidity Warranty 600,000 software-controlled power on/off cycles 20,000 hard power on/off cycles 3 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.maxtor.com From this page, click on the "Warranty Services" link. Then, click on the appropriate "Check Warranty Online" link for your product. You will be asked to provide the drive serial number. The system will display the warranty information for your drive. *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur, according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. ***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes will not contribute to battery power consumption. MobileMax Product Manual, Rev. A 5

Section	Page
1.0 Introduction 1	7
2.0 Drive specifications 3	7
2.1 Specification summary 3	7
2.2 Formatted capacity 10	7
2.3 Default logical geometry 10	7
2.4 Physical organization 10	7
2.5 Recording and interface technology 11	7
2.6 Physical characteristics 11	7
2.7 Seek time 11	7
2.8 Time to ready 12	7
2.9 Power specifications 12	7
2.9.1 Power consumption 12	7
2.9.2 Conducted noise 13	7
2.9.3 Voltage tolerance 13	7
2.10 Power-management modes 14	7
2.11 Environmental specifications 15	7
2.11.1 Ambient temperature 15	7
2.11.2 Temperature gradient 15	7
2.11.3 Humidity 15	7
2.11.4 Altitude 15	7
2.11.5 Shock 16	7
2.11.6 Vibration 16	7
2.12 Acoustics 17	7
2.13 Electromagnetic immunity 17	7
2.14 Reliability 18	7
2.15 Agency certification 18	7
2.15.1 Safety certification 18	7
2.15.2 Electromagnetic compatibility 18	7
2.15.3 FCC verification 19	7
2.16 Environmental protection 20	7
2.16.1 European Union Restriction of Hazardous Substances (RoHS) 20	7
2.17 Corrosive environment 20	7
3.0 Configuring and mounting the drive 21	7
3.1 Handling and static discharge precautions 21	7
3.2 Jumper settings 22	7
3.2.1 Master/slave configuration 22	7
3.2.2 Cable-select option 22	7
3.3 Mounting the drive 23	7
4.0 ATA interface 25	7
4.1 ATA interface signals and connector pins 25	7
4.1.1 Supported ATA commands 26	7
4.1.2 Identify Device command 28	7
4.1.3 Set Features command 31	7
5.0 Compatibility summary 33	7
5.1 Installation considerations 33	7
5.2 BIOS versions tested 35	7
5.3 Operating system versions tested 36	7
5.4 Compatibility test configurations 36	7
5.5 Other certification 36	7
6.0 Maxtor support services 37	7
Figure 1. Typical 5V startup and operation current profile 13	9
Figure 2. Jumper settings 22	9
Figure 3. Mounting dimensions-top, side and end view 23	9
1.0 Introduction	11
2.0 Drive specifications	13
2.1 Specification summary	13
2.2 Formatted capacity	20
2.3 Default logical geometry	20
2.4 Physical organization	20
2.5 Recording and interface technology	21
2.6 Physical characteristics	21
2.7 Seek time	21
2.8 Time to ready	22
2.9 Power specifications	22
2.9.1 Power consumption	22
2.9.1.1 Typical current profile	23
2.9.2 Conducted noise	23
2.9.3 Voltage tolerance	23
2.10 Power-management modes	24
2.11 Environmental specifications	25
2.11.1 Ambient temperature	25
2.11.2 Temperature gradient	25
2.11.3 Humidity	25
2.11.3.1 Relative humidity	25
2.11.3.2 Wet bulb temperature	25
2.11.4 Altitude	25
2.11.5 Shock	26
2.11.5.1 Operating shock	26
2.11.5.2 Nonoperating shock	26
2.11.6 Vibration	26
2.11.6.1 Operating vibration	26
2.11.6.2 Nonoperating vibration	26
2.12 Acoustics	27
2.13 Electromagnetic immunity	27
2.14 Reliability	28
2.15 Agency certification	28
2.15.1 Safety certification	28
2.15.2 Electromagnetic compatibility	28
2.15.3 FCC verification	29
2.16 Environmental protection	30
2.16.1 European Union Restriction of Hazardous Substances (RoHS)	30
2.17 Corrosive environment	30
3.0 Configuring and mounting the drive	31
3.1 Handling and static discharge precautions	31
3.2 Jumper settings	32
3.2.1 Master/slave configuration	32
3.2.2 Cable-select option	32
3.3 Mounting the drive	33
4.0 ATA interface	35
4.1 ATA interface signals and connector pins	35
4.1.1 Supported ATA commands	36
4.1.2 Identify Device command	38
4.1.3 Set Features command	41
5.0 Compatibility summary	43
5.1 Installation considerations	43
5.2 BIOS versions tested	45
5.3 Operating system versions tested	46
5.4 Compatibility test configurations	46
5.5 Other certification	46