Sealey CD2013 Instruction Manual - Page 2

NOTE: Children of less than 3 years should be kept away unless continuously supervised. Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance. 2. INTRODUCTION Modern design convector heater with three heat settings of 750/1250/2000W for gradual control of heating elements. Rotary controlled room thermostat maintains ambient temperature at preset level, with the addition of a thermal cut-off and overheat protection. Features hard-wearing feet to allow for maximum stability. Slimline, sturdy construction and high quality finish make this unit suitable for home, light industrial and office environments. Supplied with 3-pin plug. 3. SPECIFICATION Model No CD2013.V3 Power 750/1250/2000W Size (W x D x H 620 x 224 x 380mm Supply 230V fig.1 fig.2 4. ASSEMBLY 4.1. To fit the feet, align them as in fig.1 and secure with the A self tapping screws provided. 5. OPERATION 5.1. 5.2. 5.3. 5.4. 5.5. 5.6. 5.7. ‰ 8 Place the heater in a suitable position in the area you require to heat. fig.2 Allow a minimum of 50cm between the heater and adjacent objects such as furniture etc. Plug the heater into the mains supply. Turn the thermostat knob (fig.2.A) to a high setting. SELECTING THE HEAT OUTPUT (fig.2) Choose the required heat output by selecting the appropriate marked position (Off, I, II, III). Low setting (position I) (750W) Medium setting (position II) (1250W) High setting ((position III) (2000W) USING THE THERMOSTAT (fig.2.A) Once the required room temperature has been achieved, turn the thermostat down slowly in the direction of the min. setting until the heat output switch light goes out. The heater will then keep the surrounding air at the set temperature by switching on and off at intervals. You may reset the thermostat at any time. SAFETY CUT OUT FEATURE The heater is fitted with a thermostatic safety cut out which will turn the heater off automatically should the airflow become blocked or if the heater has a technical malfunction. Should this happen, switch the heater off and unplug it from the mains power supply. WARNING! In such a case the heater will be very hot. DO NOT connect the heater to the power supply again until the reason the safety cutout activated has been identified. Allow the heater to cool completely before handling and then check the air inlet and outlet for obstructions before attempting to switch the unit back on. If the cause is not obvious return the heater to your local Sealey stockist for servicing. 6. MAINTENANCE ‰ 6.1. 6.2. WARNING: Before attempting any maintenance ensure the unit is unplugged from the mains power supply and that it is cool. Clean the unit with a soft dry cloth. DO NOT use abrasives or solvents. Periodically check the air inlet and outlet to ensure the air way is clear. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. REGISTER YOUR PURCHASE HERE WEEE REGULATIONS Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for recycling information. Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on [email protected] or 01284 757505. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 [email protected] www.sealey.co.uk © Jack Sealey Limited Original Language Version CD2013.V3 Issue:1 31/10/22