Seiko S351 Manual - Page 6
To Preserve The Quality Of Your Stopwatch, Liquid Crystal Panel
![]() |
View all Seiko S351 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
3 After the starting time setting is completed, press buttonɹB to start the stopwatch. For the stopwatch operation, refer to the stopwatch operation explained above. A B Notes: ɾWhen the stopwatch is stopped, "STOP" and " ˅" marks are displayed. ɾWhile the stopwatch is counting, " ˅" is not displayed. ɾWhile the split time is measured, "SPLIT" and " ˅" are displayed. If button Bɹis pressed while the ɹsplit time is measured, the measurement is stopped and the total elapsed time is displayed in place ɹof the split time. ɾA negative calculation result obtained in the time calculation mode can be set as the starting time ɹwith the recall key. If button ɹ B is pressed to start the stopwatch, however, the error mark "Error" is ɹdisplayed and the stopwatch will not start counting. Press the clear/clear entry key to reset the digits ɹto "0:00˄00˅" and then enter a proper starting time. ɾThe set staring time is not stored in memoty, and it will be canceled once the stopwatch is started. ɾThe arithmetic operation keys [ʴ] [ʵ] and [ʹ] do not work in the stopwatch mode. ˙NOTES ON THE BATTERIES [Battery for the stopwatch] BATTERY LIFE A new normal battery will last approximately three years. ˎIf the timer is used more than 10 times a day, the battery life may be less than ɹthe specified period. ˎThe battery in your watch may run down in less than the specified period ɹafter the date ofpurchase, as it is a monitor battery inserted at the factory ɹto check the functions and performance of the watch. ˎThe battery in your watch will therefore be replaced with a new one only at ɹcost even if it runs down within the guarantee period. BATTERY LIFE INDICATOR When flashing "ɹ" mark appears in the upper left of the display, replace the battery with a new one as soon as possible. Otherwise, the watch may stop operating in 2 to 3 days. We suggest that you have the battery replaced by a retailer from whom your watch was purchased or a SEIKO dealer. ˎEven though the flashing "ɹ" mark is displayed, time accuracy is not ɹaffected. BATTERY CHANGE When replacing the battery, be sure to take your watch to the retailer from whom your watch was purchased or an AUTHORIZED SEIKO DEALER , and specify the " SEIKO genuine SB battery ". If an old battery is kept inside the watch for a long time, electrolyte leakage may occur and a malfunction may be caused. Be sure to replace the battery as soon as it runs down to prevent any possible malfunction. ˎWhen a battery is taken out of a watch, it must be kept at a ɹplace beyond the reach of an infant. In case it is swallowed ɹby an infant, consult a doctor immediately. ˙CARE OF YOUR STOPWATCH WATER RESISTANT ANTI-SHOCK ANTI-MAGNETIC TEMPERATURE Your watch is designed to work with stable accuracy between normal temperature range of 5°C and 35°C . Being equipped with the number entry and other keys as used in calculators, your watch is not water resistant according to the water resistance standard for watches. It can withstand, however, the accidental contact with splashes of water or rain. If the watch is wet, wipe it thoroughly dry with a soft dry cloth or the like. Light activities will not affect yourwatch, but be careful not to drop your watch or hit it against hard surfaces, as this way cause damage. Magnetism will not affect the watch ˎAs a small amount of moisture is included inside the stopwatch , the inner surface of the glass may be temporarily blurred if the atmospheric temperature is lower than that inside the stopwatch . This does not adversely affect it . However , if the blur persists for a long time, we suggest that you have the stopwatch checked by the retailer from whom it was purchased. Do not leave your watch in direct sunlight or very high temperatures for a long time. • The display may become black, but this condition will be corrected when the watch returns to normal temperature . Do not leave the watch in a very low temperature, as this may cause : 1) A slight time loss or gain. 2) The change of digits to become slow (with accuracy remaining normal.) The adove conditions will be corrected when the watch returns to normal temperature. ˎIf the watch is left in temperatures over 60ˆ or below-10ˆfor a long time,the watch maystop operating, battery leakage may be occurred, or the battery life may be shortened. CHEMICALS As plastic materials are used for the watch case, be careful not to expose the watch to solvents ( such as alcohol and gasoline), cosmetic spray, detergent, adhesives or paints, as the case, bracelet, etc. will be discolored, deteriorate or deform through the chemical action. ˙-*26*%$3:45"-1"/&-˙5013&4&37&5)&26"-*5:0':06345018"5$) STATIC ELECTRICITY The IC (Integrated Circuit) used in your watch will be affected by static electricity, which may disturb the display. Keep your watch away from close contact with suchobjects as TV screens which emit strong static electricity. After about 7 years of use digital display panel will decrease in contrast, becoming difficult to read. Have the panel replaced with a new one by the retailer from whom your watch was purchased or an AUTHORIZED SEIKO DEALER. The panel will be replaced at cost. CHECK It is recommended that the stopwatch be checked every time the battery for the stopwatch is replaced with a new one or once every 2 to 3 years . We suggest that you have your watch checked by a SEIKO DEALER when the battery is replaced, for oil condition, battery electrolyte leakage or damage due to water or sweat. After checking the watch, adjustment or repair may be required. ˎBe sure to have the gasket and push-pin replaced with new ones by a SEIKO DEALER after the watch is adjusted or repaired. ˎSpecify "SEIKO GENUINE PARTS" when replacing the parts.
![](/manual_guide/products/seiko-s351-manual-2290656/6.png)