Seiko SNJ025 Owner Manual - Page 16
Troubleshooting
View all Seiko SNJ025 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
TO PRESERVE THE QUALITY OF YOUR WATCH ● Inspection and adjustment by disassembly and cleaning (overhaul) • Periodic inspection and adjustment by disassembly and cleaning (overhaul) is recommended approximately once every 3 to 4 years in order to maintain optimal performance of the watch for a long time. According to use conditions, the oil retaining condition of your watch mechanical parts may deteriorate, abrasion of the parts may occur due to contamination of oil, which may ultimately lead the watch itself to stop. Furthermore, the digital display may go out due to liquid leaking. • The power transmission gear of the movement of this watch constantly receives force. To ensure that this mechanism works properly all the time, washing parts, changing oil, adjusting accuracy, checking functions and replacing consumable parts on a regular basis are important. The first overhaul after the purchase of your watch is particularly important for preserving long-time use of your watch. According to use conditions, the oil retaining condition of your watch mechanical parts may deteriorate, abrasion of the parts may occur due to contamination of oil, which may ultimately lead the watch itself to stop. As the parts such as gasket may deteriorate, water resistant performance may be impaired due to intrusion of perspiration and moisture. Please contact the retailer from whom the watch was purchased for inspection and adjustment by 6 disassembly and cleaning (overhaul). For replacement of parts, please specify "SEIKO GENUINE PARTS." When asking for inspection and adjustment by disassembly and cleaning (overhaul), make sure that the gasket and push pin are also replaced with new ones. • When your watch is inspected and adjusted by disassembly and cleaning (overhauled), the movement of your watch may be replaced. b CAUTION Depending on the environment where a diver's watch is used, its inner parts or movement as well as its case or band may be affected. We recommend that you have your watch overhauled regularly once every 3 or 4 years. EN 56 Troubleshooting Troubles Possible causes Solutions Referen ce TROUBLESHOOTING The watch stops operating. The seconds hand is moving at twosecond intervals. The power is completely depleted or low. If you wear the watch every day and this occurs, the most likely cause is the watch is hidden by your sleeves or other clothing when you wear it and it is not sufficiently exposed to light. Sufficiently charge the battery until the seconds hand moves every second. When you wear the watch, try to make sure that the watch is not hidden by your sleeves or other clothing. Additionally, when you take the watch off, try to place it in a bright place. P. 37 Even if the watch is charged until 7 "BATT 10" after it stops, the seconds hand The internal watch system is does not move in unstable. See "How to reset the system" → (P. 61) and follow the procedure. P. 61 one-second intervals. Or it does not work. EN 58 ● Internal watch light (LED) The watch uses a technique to uniformly diffuse light from a light emitting diode (LED) with a light guide plate. * If the battery is nearing the end of life and voltage decreases, illumination (brightness) will decrease. ● Liquid crystal panel After the liquid crystal panel in this watch has been used for seven years, the contrast will decrease and the numbers will be hard to read. Please get it replaced at the retailer from whom the watch was purchased. They will replace it for a fee. 6 EN 57 Troubles Possible causes Solutions Referen ce If the watch returns to room The watch temporarily loses time. gains/ The watch has been left in extremely high or low temperatures for a long time. temperature, the accuracy will return to its original state. If it does not return to its original state, contact the retailer from whom the watch was purchased. Correct this condition by moving and keeping the watch away from the - TROUBLESHOOTING The watch has been left close to an magnetic source, and reset the time. object with a strong magnetic field. If this action does not correct the - condition, contact the retailer from whom the watch was purchased. The buttons do not work Sufficiently charge the battery until (Nothing happens The power is low. when they are the seconds hand moves every second. P. 37 7 pressed) EN 59 TO PRESERVE THE QUALITY OF YOUR WATCH