Sennheiser XSW-D LAVALIER SET Instruction manual - XS Wireless Digital PDF - Page 37

If the status LED remains red, a fault has occurred.

Get Sennheiser XSW-D LAVALIER SET PDF manuals and user guides View all Sennheiser XSW-D LAVALIER SET manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Operation Pairing The transmitter and the receiver of a set are pre-paired at the factory and therefore ready for immediate use. The wireless connection is established once the transmitter and receiver are switched on and within range of each other. You can pair up to four transmitters to the receiver. Please note that you can only use one transmitter at a time. The other paired transmitters must be switched off in the meantime. ▷ Make sure that both the transmitter and receiver are switched off. ► ▷ Press the button on the transmitter and the button on the receiver until the status LEDs start flashing green and red in alternation. The status LEDs will remain green once the transmitter and receiver are paired and connected. If the status LEDs do not remain green, the charge level is below 15% (see „Checking the charge level during use"). Out-of-range monitoring The status LEDs begin flashing red when the transmitter and receiver are almost out of range. Correcting faults If the status LED remains red, a fault has occurred. ▷ Unplug any connected USB cables from the UBS port. ▷ Switch the transmitter and receiver off and on again. ▷ Perform pairing, if necessary. ▷ If this does not correct the fault, please contact Sennheiser customer service: www.sennheiser.com/service-support 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Operation
36
Pairing
The transmitter and the receiver of a set are pre-paired at the factory and
therefore ready for immediate use. The wireless connection is established
once the transmitter and receiver are switched on and within range of each
other.
You can pair up to four transmitters to the receiver.
Please note that you can only use one transmitter at a time. The other
paired transmitters must be switched off in the meantime.
▷
Make sure that both the transmitter and receiver are switched off.
►
▷
Press the button on the transmitter and the button on the receiver until
the status LEDs start flashing green and red in alternation.
The status LEDs will remain green once the transmitter and receiver
are paired and connected. If the status LEDs do not remain green, the
charge level is below 15% (see „Checking the charge level during use“).
Out-of-range monitoring
The status LEDs begin flashing red when the transmitter and receiver are
almost out of range.
Correcting faults
If the status LED remains red, a fault has occurred.
▷
Unplug any connected USB cables from the UBS port.
▷
Switch the transmitter and receiver off and on again.
▷
Perform pairing, if necessary.
▷
If this does not correct the fault, please contact Sennheiser customer
service:
www.sennheiser.com/service-support