Sharp EL-531WB-BL EL-W531 , EL-W531G , EL-W531H , EL-W531HA , EL-W535 Operatio - Page 4

For More Information About Scientific Calculators - manual

Page 4 highlights

Error codes and error types ERROR 01: Syntax error • An attempt was made to perform an invalid operation. Ex. 2 + & 5 = ERROR 02: Calculation error • The absolute value of an intermediate or final calculation result equals or exceeds 10100. • An attempt was made to divide by zero (or an intermediate calculation resulted in zero). • The calculation ranges were exceeded while performing calculations. ERROR 03: Nesting error • The available number of buffers was exceeded. (There are 10 buffers for numeric values and 64 buffers for calculation instructions). ERROR 04: Data over • Data items exceeded 100 in STAT mode. Alert Messages 18 Cannot delete! • The selected item cannot be deleted by pressing N or @ y in the WriteView editor. Ex. * 5 r A l N In this example, delete the exponent before attempting to delete the parentheses. Cannot call! • The function or operation stored in definable memory (D1 to D4) cannot be called. Ex. An attempt was made to recall a statistical variable from within NORMAL mode. Buffer full! • The equation (including any calculation ending instructions) exceeded its maximum input buffer (159 characters in the WriteView editor or 161 characters in the Line editor). An equation may not exceed its maximum input buffer. • If the product is not to be used for some time, to avoid damage to the unit from a leaking battery, remove it and store in a safe place. • Do not leave an exhausted battery inside the product. • Keep batteries out of the reach of children. • An exhausted battery left in the calculator may leak and damage the calculator. • Explosion risk may be caused by incorrect handling. • Do not throw batteries into a fire as they may explode. Replacement Procedure 1.Turn the power off by pressing @ o. 2.Remove the two screws. (Fig. 1) 3.Slide the battery cover slightly and lift it to remove. 4.EL-W531/W531G/W535: Remove the used battery by prying it out with a ball-point pen or other similar pointed device. (Fig. 2) EL-W531H/W531HA: Remove the used battery. 5.EL-W531/W531G/W535: Install one new battery. Make sure the "+" side is facing up. EL-W531H/W531HA: Install one new battery. First insert the "−" side toward the spring. (Fig. 3) 6.Replace the cover and screws. 7.Press the RESET switch (on the back) with the tip of a ball-point pen or similar object. 8.Adjust the display contrast. See "Adjusting the Display Contrast". • Make sure that the display appears as shown below. If the display does not appear as shown, remove the battery, reinstall it, and check the display once again. Fig. 1 Fig. 2 Fig. 3 Calculation Ranges 19 • Within the ranges specified, this calculator is accurate to ±1 of the 10th digit of the mantissa. However, a calculation error increases in continuous calculations due to accumulation of each calculation error. (This is the same for y x, xr, n!, ex, ln, etc., where continuous calculations are performed internally.) Additionally, a calculation error will accumulate and become larger in the vicinity of inflection points and singular points of functions. • Calculation ranges ±10−99 to ±9.999999999 × 1099 and 0. If the absolute value of an entry or a final or intermediate result of a calculation is less than 10−99, the value is considered to be 0 in calculations and in the display. Display of results using r Calculation results may be displayed using r when all of the following conditions are met: • When intermediate and final calculation results are displayed in the following form: ±a⎯ P eb ± c⎯ P fd • When each coefficient falls into the following ranges: 1 ≤ a < 100; 1 < b < 1,000; 0 ≤ c < 100; 1 ≤ d < 1,000; 1 ≤ e < 100; 1 ≤ f < 100 • When the number of terms in the intermediate and final calculation results is one or two. Note: The result of two fractional terms that include r will be reduced to a common denominator. BATTERY REPLACEMENT Notes on Battery Replacement Improper handling of batteries can cause electrolyte leakage or explosion. Be sure to observe the following handling rules: • Make sure the new battery is the correct type. • When installing, orient the battery properly as indicated in the calculator. • The battery is factory-installed before shipment, and may be exhausted before it reaches the service life stated in the specifications. Notes on erasure of memory contents When the battery is replaced, the memory contents are erased. Erasure can also occur if the calculator is defective or when it is repaired. Make a note of all important memory contents in case accidental erasure occurs. When to Replace the Battery EL-W531/W531H/W531HA/W535: If the display has poor contrast even after adjusting the display contrast, the battery requires replacement. EL-W531G: If the display has poor contrast or nothing appears on the display when j is pressed in dim lighting, even after adjusting the display contrast, it is time to replace the battery. Cautions • Fluid from a leaking battery accidentally entering an eye could result in serious injury. Should this occur, wash with clean water and immediately consult a doctor. • Should fluid from a leaking battery come in contact with your skin or clothes, immediately wash with clean water. Automatic Power Off Function This calculator will turn itself off to save battery power if no key is pressed for approximately 10 minutes. SPECIFICATIONS Calculation features: Scientific calculations, statistical calculations, etc. Drill features: Math Drill and Multiplication Table Display: 96 × 32 dot matrix liquid crystal display Display of calculation results: Mantissa: 10 digits Exponent: 2 digits Internal calculations: Mantissas of up to 14 digits Pending operations: 64 calculations 10 numeric values Power source: EL-W531/W535 1.5 V -... (DC): Alkaline battery (LR44 or equivalent) × 1 EL-W531G Built-in solar cells 1.5 V -... (DC): Backup battery (Alkaline battery (LR44 or equivalent) × 1) EL-W531H/W531HA 1.5 V -... (DC): Heavy duty manganese battery (size AAA or R03) × 1 Power consumption: EL-W531/W531H/W531HA/W535 0.00011 W Operating time: EL-W531/W535 (varies according to Approx. 3,000 hours when continuously use and other factors) displaying 55555. at 25°C (77°F) EL-W531G Approx. 3,000 hours when continuously displaying 55555. at 25°C (77°F), using the alkaline battery only EL-W531H/W531HA Approx. 17,000 hours when continuously displaying 55555. at 25°C (77°F) Operating temperature: 0°C-40°C (32°F-104°F) External dimensions: 79.6 mm (W) × 161.5 mm (D) × 15.5 mm (H) 3-1/8" (W) × 6-11/32" (D) × 5/8" (H) Weight: EL-W531/W535 Approx. 100 g (0.22 lb) (including battery) EL-W531G Approx. 102 g (0.23 lb) (including battery) EL-W531H/W531HA Approx. 107 g (0.24 lb) (including battery) Accessories: Battery × 1 (installed), operation manual, and hard case FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS Visit our Web site. http://sharp-world.com/calculator/

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8

Error codes and error types
ERROR 01: Syntax error
• An attempt was made to perform an invalid operation.
Ex. 2
+
&
5
=
ERROR 02: Calculation error
• The absolute value of an intermediate or final calculation
result equals or exceeds 10
100
.
• An attempt was made to divide by zero (or an intermediate
calculation resulted in zero).
• The calculation ranges were exceeded while performing
calculations.
ERROR 03: Nesting error
• The available number of buffers was exceeded. (There are
10 buffers for numeric values and 64 buffers for calculation
instructions).
ERROR 04: Data over
• Data items exceeded 100 in STAT mode.
Alert Messages
18
Cannot delete!
• The selected item cannot be deleted by pressing
N
or
@
y
in the WriteView editor.
Ex.
*
5
r
A
l
N
In this example, delete the exponent before attempting to
delete the parentheses.
Cannot call!
• The function or operation stored in definable memory (D1 to
D4) cannot be called.
Ex. An attempt was made to recall a statistical variable from
within NORMAL mode.
Buffer full!
• The equation (including any calculation ending instructions)
exceeded its maximum input buffer (159 characters in the
WriteView editor or 161 characters in the Line editor). An
equation may not exceed its maximum input buffer.
Calculation Ranges
19
Within the ranges specified, this calculator is accurate to
±
1 of the 10th digit of the mantissa. However, a calculation
error increases in continuous calculations due to
accumulation of each calculation error. (This is the same
for
y
x
,
x
r
, n!, e
x
, ln, etc., where continuous calculations
are performed internally.)
Additionally, a calculation error will accumulate and
become larger in the vicinity of inflection points and
singular points of functions.
• Calculation ranges
±
10
99
to
±
9.999999999
×
10
99
and 0.
If the absolute value of an entry or a final or intermediate
result of a calculation is less than 10
99
, the value is
considered to be 0 in calculations and in the display.
Display of results using
r
Calculation results may be displayed using
r
when all of the
following conditions are met:
• When intermediate and final calculation results are displayed
in the following form:
±
a
P
b
e
±
c
P
d
f
• When each coefficient falls into the following ranges:
1
a
<
100; 1
<
b
<
1,000; 0
c
<
100;
1
d
<
1,000; 1
e
<
100; 1
f
<
100
• When the number of terms in the intermediate and final
calculation results is one or two.
Note: The result of two fractional terms that include
r
will be
reduced to a common denominator.
BATTERY REPLACEMENT
Notes on Battery Replacement
Improper handling of batteries can cause electrolyte leakage or
explosion. Be sure to observe the following handling rules:
• Make sure the new battery is the correct type.
• When installing, orient the battery properly as indicated in the
calculator.
• The battery is factory-installed before shipment, and may
be exhausted before it reaches the service life stated in the
specifications.
Notes on erasure of memory contents
When the battery is replaced, the memory contents are
erased. Erasure can also occur if the calculator is defective
or when it is repaired. Make a note of all important memory
contents in case accidental erasure occurs.
When to Replace the Battery
EL-W531/W531H/W531HA/W535
: If the display has poor
contrast even after adjusting the display contrast, the battery
requires replacement.
EL-W531G
: If the display has poor contrast or nothing appears
on the display when
j
is pressed in dim lighting, even after
adjusting the display contrast, it is time to replace the battery.
Cautions
• Fluid from a leaking battery accidentally entering an eye could
result in serious injury. Should this occur, wash with clean
water and immediately consult a doctor.
• Should fluid from a leaking battery come in contact with your
skin or clothes, immediately wash with clean water.
• If the product is not to be used for some time, to avoid
damage to the unit from a leaking battery, remove it and
store in a safe place.
• Do not leave an exhausted battery inside the product.
• Keep batteries out of the reach of children.
• An exhausted battery left in the calculator may leak and
damage the calculator.
• Explosion risk may be caused by incorrect handling.
• Do not throw batteries into a fire as they may explode.
Replacement Procedure
1. Turn the power off by pressing
@
o
.
2. Remove the two screws. (Fig. 1)
3. Slide the battery cover slightly and lift it to remove.
4.
EL-W531/W531G/W535
: Remove the used battery by
prying it out with a ball-point pen or other similar pointed
device. (Fig. 2)
EL-W531H/W531HA
: Remove the used battery.
5.
EL-W531/W531G/W535
: Install one new battery. Make sure
the “
+
” side is facing up.
EL-W531H/W531HA
: Install one new battery. First insert the
” side toward the spring. (Fig. 3)
6. Replace the cover and screws.
7. Press the RESET switch (on the back) with the tip of a
ball-point pen or similar object.
8. Adjust the display contrast. See “Adjusting the Display
Contrast”.
• Make sure that the display appears as shown below. If the
display does not appear as shown, remove the battery,
reinstall it, and check the display once again.
Fig. 1
Fig. 2
Fig. 3
Automatic Power Off Function
This calculator will turn itself off to save battery power if no
key is pressed for approximately 10 minutes.
SPECIFICATIONS
Calculation features:
Scientific calculations, statistical
calculations, etc.
Drill features:
Math Drill and Multiplication Table
Display:
96
×
32 dot matrix liquid crystal display
Display of calculation results:
Mantissa: 10 digits
Exponent: 2 digits
Internal calculations:
Mantissas of up to 14 digits
Pending operations:
64 calculations 10 numeric values
Power source:
EL-W531/W535
1.5 V …
— (DC): Alkaline battery (LR44 or
equivalent)
×
1
EL-W531G
Built-in solar cells
1.5 V …
— (DC): Backup battery
(Alkaline battery (LR44 or equivalent)
×
1)
EL-W531H/W531HA
1.5 V …
— (DC): Heavy duty manganese
battery (size AAA or R03)
×
1
Power consumption:
EL-W531/W531H/W531HA/W535
0.00011 W
Operating time:
(varies according to
use and other factors)
EL-W531/W535
Approx. 3,000 hours when continuously
displaying 55555. at 25°C (77°F)
EL-W531G
Approx. 3,000 hours when continuously
displaying 55555. at 25°C (77°F), using
the alkaline battery only
EL-W531H/W531HA
Approx. 17,000 hours when continuously
displaying 55555. at 25°C (77°F)
Operating temperature:
0°C–40°C (32°F–104°F)
External dimensions:
79.6 mm (W)
×
161.5 mm (D)
×
15.5 mm (H)
3-1/8” (W)
×
6-11/32” (D)
×
5/8” (H)
Weight:
EL-W531/W535
Approx. 100 g (0.22 lb) (including battery)
EL-W531G
Approx. 102 g (0.23 lb) (including battery)
EL-W531H/W531HA
Approx. 107 g (0.24 lb) (including battery)
Accessories:
Battery
×
1 (installed), operation
manual, and hard case
FOR MORE INFORMATION ABOUT SCIENTIFIC CALCULATORS
Visit our Web site.
http://sharp-world.com/calculator/