Sharp FO-2081 Startup Guide - Page 1
Sharp FO-2081 Manual
View all Sharp FO-2081 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
MODEL: FO-2081 DIGITAL MULTIFUNCTIONAL SYSTEM START GUIDE This guide explains how to install the machine, and indicates important points to note for installation and usage. Read and understand this guide to ensure that you install the machine correctly. The Operation Guide for the machine is on the accompanying CD-ROM. The procedure for viewing the guide is explained in "How to use the operation guide". After installation, read the Operation Guide to make full use of all the machine has to offer. POWER ON If you use the unit in a country other than the country where the unit was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the unit into an incompatible power supply, irreparable damage to the unit will result. 1 Ensure that the power switch of the unit is in the "OFF" position. 2 Turn the power switch on the left side of the unit to the "ON" position. OFF If you are using distinctive ringing with an answering machine, you do not need to follow the procedure described below. (Please note that when distinctive ringing is used, the answering machine must be distinctive ring compatible.) Comments: 1.It is advisable to keep the length of the message under 10 seconds. If it is too long, you may have difficulty receiving faxes sent by automatic dialing. 2.Your callers can even leave a voice message and send a fax message on the same call. Modify your outgoing message to explain that this can be done by pressing their [START] key ( ) after leaving their voice message. • You can connect an extension phone to the machine to make and receive calls like any other extension phone on your line. Even if you pick up the extension phone and hear a fax tone, the machine will automatically cut in and take over the line. Note, however, if you also have a PC modem on the same line, you must turn on the Remote Reception function, and deactivate the Fax Signal Receive function. See "SETTING UP THE MACHINE FOR USE WITH A PC MODEM" (p.37) and "USING THE REMOTE RECEPTION FUNCTION" (p.38). The Remote Reception function is initially set to "ON". ON About the scan head The scan head lamp remains on constantly when the unit is in the ready condition (when the start ( ) indicator is illuminated). The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate unit trouble. CONNECTIONS CONNECTING THE TELEPHONE LINE CORD Plug one end of the telephone line cord into the jack on the machine marked "LINE." Plug the other side into a standard (RJ11C) single- line telephone wall jack. Be sure not to plug this telephone line cord into the "TEL" jack. The "TEL" jack is used to attach an extension TEL telephone or answering machine to the machine. (See "CONNECTING OTHER LINE DEVICES") If your area experiences a high incidence of lightning or power surges, we recommend that you install surge protectors for the power and telephone lines. Surge protectors can be purchased from your retailer or at most telephone specialty stores. FINAL PREPARATIONS CONNECTING OTHER DEVICES If desired, an answering machine or external telephone can be connected to the machine through the telephone jack, labeled "TEL," on the rear of the machine. • Connecting an answering machine to the machine allows you to receive both voice and fax messages when you are out. To use this feature, first change the outgoing message of your answering machine, and then set the reception mode of the machine to "A.M." (Answering Machine mode) when you go out. ABOUT THE OPERATION GUIDES The operation guides for the machine are as follows: Start Guide (this manual) This manual covers the procedures for setup and the safety relations. Operation Guide for machine (on the FO-2081 Operation Guide CD-ROM) Explains the machine and how to use it as a copier. Also explains how to use the machine as a printer and scanner for your computer. Operation Guide for fax (on the FO-2081 Operation Guide CDROM) This manual explains the procedures for using the machine as a fax machine. This manual only explains the fax functions of the machine. For general information on using the machine, including safety information, installation, paper loading, removal of paper misfeeds, and peripheral equipment, see the operation guide for the machine. How to use the operation guide Detailed explanations of the functions that can be used on the machine are provided in the Operation Guide in PDF format. 1 Insert the supplied CD-ROM into your computer's CD-ROM drive. 2 Display the contents of the CDROM, and open the Operation Guide file. Operation Guide CD-ROM Manual Operation Guide file (PDF) US_English * To view the Operation Guide in PDF format, Adobe® Reader® or Acrobat® Reader® of Adobe Systems Incorporated is required. Adobe® Reader® can be downloaded from the following URL: http://www.adobe.com/ PRINTED IN CHINA 2011D KS1 TINSE2164QSZZ SPECIFICATIONS Model Type Photoconductive type Document glass type Copy/printing system Originals Originals size Copy size Copying speed*1 Continuous copy First-copy time*2 Warm-up time*3 Copy ratio Exposure system Paper feed Fusing system Developer system Light source Resolution Gradation Power supply Power consumption Overall dimensions (with bypass tray folded) Weight*4 Dimensions Operating conditions Noise level FO-2081 Digital Multifunctional System, Desktop OPC drum Fixed Dry, electrostatic transfer Sheets, bound documents Max. 8-1/2" x 14" (A4) Max. 8-1/2" x 14" (A4) Min. 5-1/2" x 8-1/2" (A5) Image loss: Max. 11/64" (4 mm) (leading and trailing edges) Max. 3/16" (4.5 mm) (along other edges in total) Max. 1/4" (6 mm) (trailing edge of the second copy of twosided copying.) 20 copies/min. (8-1/2" x 11" (A4) one-sided copying at 100% copy ratio) Max. 99 copies; subtractive counter 8.0 seconds (When user program 24 is set to OFF) 10.7 seconds (When user program 24 is set to ON) (paper: A4, exposure mode: AUTO, copy ratio: 100%) Approx. 0 sec. Document glass: Variable: 25% to 400% in 1% increments (total 376 steps) Fixed preset: Inch system: 25%, 50%, 64%, 78%, 100%, 129%, 200%, 400% AB system: 25 %, 50 %, 70 %, 86 %, 100 %, 141 %, 200 %, 400% RSPF: Variable: 50% to 200% in 1% increments (total 151 steps) Fixed preset: Inch system: 50%, 64%, 78%, 100%, 129%, 200% AB system: 50 %, 70 %, 86 %, 100 %, 141 %, 200 % Document glass: Moving optical source, slit exposure (stationary platen) with automatic exposure function RSPF: Moving original One automatic feeding paper tray and one optional paper tray (250 sheets each) + bypass tray (50 sheets) Heat rollers Magnetic brush development Tri-color CCD light source (CCD: 3 components; R, G, and B) Scan: 600 x 300 dpi Output: 600 x 600 dpi (AUTO/TEXT mode) Scan: 600 x 600 dpi Output: 600 x 600 dpi (PHOTO mode) 256 tones (8 bits) Local voltage ±10% (For this copier's power supply requirement, see the name plate located on the back of the unit.) Max. 1.0 kW 31-5/8" (W) x 18-1/8" (D) (802 mm (W) x 460 mm (D)) Approx. 42.1 lb. (19.1kg) 20-3/8" (W) x 18-1/8" (D) x 14-3/4" (H) (518 mm (W) x 460 mm (D) x 376 mm (H)) Temperature: 50°F to 86°F (10°C to 30°C), Humidity: 20% to 85% Sound power level LwAd Copying mode: 6.7 B Standby mode: - (*) Sound pressure level LpAm (reference) (Bystander positions) Copying mode: 51 dB Standby mode Less than background noise Noise emission measurement in accordance with ISO7779. *1 When making multiple duplex copies, the copy speed will vary based on the environment conditions. *2 First copy time may vary depending on the status of the machine. *3 The warm-up time may vary depending on the ambient conditions. *4 Not including TD and drum cartridges. Printer Function Print speed* Max. 20 ppm (when printing on A4 size paper) Resolution 600 dpi/300 dpi Memory 128 MB Emulation PCL6 Installed fonts PCL6 compatible 80 outline fonts and 1 bitmap font. Interface 10 Base-T /100 Base-TX Ethernet, USB 2.0 (Full-Speed/HiSpeed compatible interface) Interface cables [USB cable] USB cable that supports USB 2.0. Please purchase a commercially available USB cable. [LAN cable] Shielded type cable: Please purchase a commercially available LAN cable. Scanner Function Type Scanning method Light source Resolution Original types Effective scanning area Scanning speed Input Data Output Data Scanning colors Protocol Interface Drop out color Supported operating systems Void area Interface cables Scanner utilities Flatbed scanner Document glass/RSPF Tri-color CCD light source (CCD: 3 components; R, G, and B) Basic: 600 dpi x 600 dpi Setting range: 50 dpi - 9600 dpi Sheet media, books 8-1/2" (Lengthwise) x 14" (Width) (216 mm (Lengthwise) x 356 mm (Width)) 2.88 msec/line A/D 16 bit R.G.B 1 or 8 bits/pixel Black and white 2 value, Grayscale, Full color TWAIN WIA (Windows XP/Vista/7 only) STI 10 Base-T /100 Base-TX Ethernet, USB 2.0 (Full-Speed/ Hi-Speed compatible interface) Yes Windows 2000 Professional/XP/Vista/7 None [USB cable] USB cable that supports USB 2.0. Please purchase a commercially available USB cable. [LAN cable] Shielded type cable: Please purchase a commercially available LAN cable. Button Manager/Sharpdesk Facsimile Function Applicable telephone line Public switched telephone network Compression method MH, MR, MMR, JBIG Transmission modes Super G3, G3 (the machine can only send faxes to and receive faxes from machines that support G3 or Super G3) Scanning method CCD flatbed scanning Scanning resolution (supports ITU-T standards) 8 x 3.85 lines/mm (Standard) 8 x 7.7 lines/mm (Fine, Fine + Halftone) 8 x 15.4 lines/mm (Super Fine, Super Fine + Halftone) Recording method Laser, electrostatic charge method Transmission speed 33.6 kbps 2.4 kbps Automatic fallback Transmission time Approx. 2 seconds (Super G3 mode / 33.6 kbps, JBIG), Approx. 6 seconds (G3 ECM mode / 14.4 kbps, JBIG) Paper size 8-1/2" x 11"(Letter), 8-1/2" x 14"(Legal), or A4 Effective recording width 8-1/2" max. (8-1/2" x 14" printing) Transmittable original size When using the RSPF Maximum One-sided original: 8-1/2" x 19.7" Two-sided original: 8-1/2" x 14" Minimum 8-1/2" x 5-1/2" When using the document glass Maximum 8-1/2" x 14" Effective scanning width 8-1/2" maximum Halftone transmission 256 levels Contrast (exposure) adjustment Light, Medium, Dark Extension telephone connection Possible (1 telephone) Auto dialing Combined total of 18 One-Touch Dial and Group keys; 100 Speed Dial numbers; redialing (automatic) Timer transmission Yes Automatic document feeding Yes (50 pages) Memory capacity 2 MB Error Correction Mode (ECM) Yes 250-sheet paper feed unit (MX-CS10) Paper size Paper weight 5-1/2" x 8-1/2" to 8-1/2" x 14" (A5 to A4) 15 lbs. to 21 lbs. (56 g/m2 to 80 g/m2 ) Paper capacity One paper tray with capacity for 250 sheets of 80 g/m2 bond paper Weight Approx. 6.6 lbs. (3 kg) Dimensions 19-5/8" (W) x 17-1/2" (D) x 3-1/2" (H) (498 mm (W) x 445 mm (D) x 88 mm (H)) Power supply Drawn from the machine As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.