Sharp MX-450U MX-M350U MX-M450U MX-M350N MX-M450N Operation Manual
Sharp MX-450U Manual
![]() |
View all Sharp MX-450U manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp MX-450U manual content summary:
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 1
MODEL MX-M350U MX-M450U MX-M350N MX-M450N LASER PRINTER OPERATION MANUAL (for general information and copier operation) Page PART 1: GENERAL INFORMATION • BEFORE USING THE PRODUCT 1-1 • MANAGING THE MACHINE 2-1 • PERIPHERAL DEVICES 3-1 PART 2: COPIER OPERATION • MAKING COPIES 4-1 • - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 2
user will be required to correct the interference at his own expense. Shielded interface cables must be used with this equipment to maintain compliance with EMC regulations. This operation manual is also used for the MX-350 / MX-450 / MX-350 J / MX-450 J / MX-M350U J / MX-M450U J / MX-M350N J / MX - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 3
of Netscape Communications Corporation. • Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries. • PCL is a registered trademark of the Hewlett-Packard Company. • IBM, PC/AT - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 4
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 5
Part 1: General Information - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 6
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 7
send Copier Printer Network printer Facsimile Network scanner Internet fax Document filing Metadata send Required peripheral devices Standard Standard Network expansion kit Facsimile expansion kit Network expansion kit, network scanner expansion kit Network expansion kit (with hard drive), network - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 8
for machine management, copying, and document filing. Administrator settings for the fax, printer, network scanner and Internet fax functions are explained in the manuals for those functions. ● Software setup guide This manual mainly explains how to install and configure the software that allows - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 9
●subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater. 4.Be sure to allow the required space around the machine for servicing and proper ventilation. 31-1/2" (80cm) an objectionable odor, it is advisable to place the copier in a ventilated area. 0-3 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 10
service technician. Absolutely do not touch this part. Some models include the document filing function, which stores document image data on the machine's hard disk. Stored documents can be called up and printed or transmitted as needed. If a hard SHARP DEALER OR AUTHORIZED SERVICE REPRESENTATIVE - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 11
10 nm -15 nm North America: Europe: 0.2 mW - 0.4 mW 35 cpm model: (4.1 µs ± 4.1 ns)/7 mm 45 cpm model: (5.7 µs ± 5.7 ns)/7 mm 35 cpm model: (3.8 µs ± 3.8 ns)/7 mm 45 cpm model: (4.4 µs ± 4.4 ns)/7 mm At the production line, the output power of the scanner with 21 CFR 1040.10 and 1040.11 of - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 12
FINISHER 3-7 ● Part names 3-7 ● Specifications 3-7 ● Finisher functions 3-8 ● Using the finisher functions 3-9 ● Staple cartridge replacement 3-10 ● Misfeed in the finisher 3-12 ● Troubleshooting finisher problems 3-13 SADDLE STITCH FINISHER 3-14 ● Part names 3-14 ● Specifications 3-14 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 13
Quick File 7-6 ● Filing 7-7 ● Print jobs 7-9 ● Scan Save 7-10 CALLING UP AND USING A FILE 7-13 ● Searching for and calling up a saved file 7-13 ● Calling up and using a saved file 7-15 ● File selection screen 7-16 SYSTEM SETTINGS 7-24 ● Creating, editing, and deleting user names and folders - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 14
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 15
basic information that should be read before using the product. Page INTRODUCTION 1-2 MAIN FEATURES 1-3 PART NAMES AND FUNCTIONS 1-9 ● Exterior 1-9 ● Interior 1-10 ● Part names and functions of peripheral devices 1-11 ● Operation panel 1-13 ● Touch panel 1-14 TURNING THE POWER ON AND OFF - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 16
the copier and document filing functions. Separate manuals have been provided for the fax function, printer function, and network scanner function B4 8-1/2" x 13" (FOOLSCAP) A4 8-1/2" x 11" (LETTER) B5 7-1/4" x 10-1/2" (EXECUTIVE) A5 5-1/2" x 8-1/2" (INVOICE) ■ The meaning of "R" in original - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 17
is installed.) ● Pamphlet Copy See page 1-4 ● Staple sort mode See page 1-7 ● Job Build See page 1-5 (When the Finisher or Saddle stitch finisher is installed.) ● Tandem Copy See page 1-5 ● Saddle stitch See page 1-7 (MX-M350N/MX-M450N, or when the network (When the Saddle stitch finisher is - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 18
copies of books or thick originals can be erased. Original Copy Edge erase Center erase Edge+Center erase XY Zoom See page 4-18 Separate ratio settings can be selected for the length and width of a copy. Original Copy Dual Page Copy See page 5-5 The left and right pages of a book can - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 19
copied onto a single sheet of paper in a uniform layout. Originals (1-sided) Originals (2-sided) Copy 100 sets of copies 50 sets of copies 50 sets of copies * MX-M350N/MX-M450N, or when the network function has been added Covers/inserts See page 5-12 Front covers, back covers, and inserts - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 20
5-42 Various steps of a copy operation can be stored as a program, and up to 10 programs can be stored. Saving frequently used sets of settings in a program saves you the trouble of selecting those settings each time you wish to use them. JOB PROGRAMS PRESS PROGRAM NUMBER. RECALL B/W Reverse - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 21
Entered text can be added to copies. Meeting *When the Finisher or Saddle stitch finisher is installed. Staple sort mode See page 3-8, 3-16 Sets of copies can be automatically stapled. Original Copy Interrupting a copy run See page 5-44 A copy job in progress can be interrupted for a rush - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 22
the administrator settings, preheat mode automatically reduces the temperature of the fusing unit to save power while the machine is on standby. When a fax or print job is received, or keys are pressed on the operation panel, or an original is placed for a copy, fax, or network scanner job, preheat - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 23
can be scanned at once. (4) Duplex module* Module for two-sided printing (5) Upper paper output area (Center tray) Finished sheets are deposited here. (6) Upper exit tray extension* Provides support for large size paper. (11) (13) (7) Operation panel (8) Front cover Open to add toner. (9) Power - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 24
19) (14) Duplex module side cover (17) Toner cartridge (drum/toner cartridge) Open when a misfeed has occurred in the duplex module. The toner cartridge must be replaced when ) Cartridge lock lever When replacing the drum, toner or developer cartridge, turn down this lever and pull it out. 1-10 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 25
for installation into the finisher. (9) Duplex module (AR-DU3) An optional duplex module must be installed for automatic two-sided printing. (10) Duplex module/bypass tray (AR-DU4) This module is basically the same as (9) above with the addition of a manual bypass paper feed unit. (11) Exit - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 26
or MX-M450U, the network expansion kit is required. ●Internet fax expansion kit (MX-FWX1) This kit is required to use the Internet fax function. To add on the Internet fax function, the network scanner expansion kit is required. On the MXM350U/MX-M450U, the network expansion kit (with hard drive) is - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 27
(Clear all key) This key is used in copy mode, document filing mode*1, network scanner mode*2, fax mode*3, and Internet fax mode*4. Use the key to cancel settings and perform an operation from the initial machine *1 MX-M350N/MX-M450N, or when the document filing function has been added. *2 When the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 28
manual are printed images, and may appear different from the actual screens. ■ Using the touch panel [Example 1] JOB QUEUE COPY Items on the touch panel SETS " in the administrator setting. (See page 10 of the administrator settings guide.) [Example 3] READY TO SCAN FOR COPY. A corresponding - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 29
to change the paper size because the specified paper size is not available, touch the current job key to select it and then touch the [DETAIL] key described in (10). Print mode Copy mode SCAN mode Scan to e-mail job Scan to FTP job Scan to Desktop job Scan to Network folder job Fax mode Fax - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 30
print mode (copying, printing, fax reception, Internet fax reception, and self printing). (4) [SCAN TO] key This displays the transmission status and finished jobs of scan mode (Scan to e-mail, Scan to FTP, Scan to Desktop, and Scan to Network Folder) when the network scanner "JOB SETTINGS" menu - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 31
or unplugging the power cord while the lights are blinking may damage the hard disk and cause the data being stored or received to be lost. If the fax function has been added, always keep the fax power switch turned on. Faxes cannot be received if the fax power switch is turned off. (Faxes can be - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 32
printed and transmitted (scanned) by each account (up to 500 accounts can be established). The page counts can be viewed and totaled as needed. - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 33
General procedure for system settings 2-12 ● About the settings 2-14 REPLACING THE TONER CARTRIDGE 2-15 STORAGE OF SUPPLIES 2-16 MISFEED REMOVAL 2-17 ● Misfeed removal guidance 2-17 ● Misfeed in the transport area, fusing area, and exit area 2-18 ● Misfeed in the duplex module 2-19 ● Misfeed - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 34
supplied by SHARP. (See page 2-4.) ● When you change the paper type and size in paper tray 1, set the paper type and size referring to "Setting the paper type and paper size" (page 2-5). ● Do not place heavy objects or press hard on any tray which is pulled out. ● Load paper with the print side face - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 35
105g/m2 the following paper sizes can be used with the automatic detection function: 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2" ● If "AUTO-AB" is selected in setting the paper type and paper size (page 2-5), the following paper sizes can be used with the automatic - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 36
paper. Do not use labels other than SHARP recommended labels. Doing so may leave adhesive residue in the machine, causing paper misfeeds, smudges on prints or other machine trouble. ● Japanese official postcards can be used. ● Applicable standard envelopes: COM-10, Monarch, DL, C5, ISO B5, CHOKEI - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 37
the [TRAY SETTINGS] key. PAPER TRAY SETTINGS TRAY SETTINGS 4 Display the setting screen of the desired paper tray. SYSTEM SETTINGS PAPER TRAY SETTINGS TYPE / SIZE TRAY 1 PLAIN / 81/2x11 PRINT COPY DOC. FAX I-FAX FILING OK FIXED PAPER SIDE 1/8 DISABLE DUPLEX DISABLE STAPLE DISABLE PUNCH - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 38
type. 9 Select output functions that can be used with the selected tray. PRINT COPY DOC. FAX I-FAX FILING Touch the checkboxes under the desired items to select them. Checkboxes that /8 NON STANDARD SIZE 6 Perform steps 8 through 10 of "Setting the paper type and paper size" (See above). 2-6 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 39
in "DISABLING OF 2 DUPLEX" in the administrator settings (page 11 of the administrator settings guide), do not use this setting. "DISABLE DUPLEX" : Prohibits two-sided printing. Enable when the back side of the paper cannot be printed on. "DISABLE STAPLE" : Prohibits stapling. Enable when using - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 40
To change the paper size or paper type when paper is loaded into the multi purpose drawer, refer to page 2-5 for details. ■ Setting envelopes or postcards When setting envelopes or postcards in the multi purpose drawer, set them in the orientation shown below. Loading postcards Load postcards print - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 41
windows, linings, self-adhesive patches or synthetic materials. Attempting to print on these may cause misfeeds, inadequate toner adherence or other trouble feeding envelopes. If not, inadequate toner adherence, paper misfeeds or other trouble may occur. 1 Unlatch the duplex module and slide it to - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 42
sheets of SHARP recommended plain paper can be loaded in these trays. The method of loading paper is the same as for paper tray 1 in the main unit. See the description (page 2-2). NOTE If the paper size or paper type is changed in either paper tray, the tray settings must be changed in system - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 43
sheets. After loading paper, be sure to return the paper guide. 4 Set the paper type. If you have changed the paper size from the AB system to the inch system sheets (20 lbs. (80 g/m2)) 23-3/16" (W) x 24-51/64" (D) x 15-29/32" (H) (589 mm (W) x 630 mm (D) x 404 mm (H)) Approximately 75 lbs. or 34 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 44
the [CLOCK] key is explained below. SYSTEM SETTINGS EXIT TOTAL COUNT ADDRESS CONTROL DEFAULT SETTINGS SENDER CONTROL LIST PRINT FAX DATA RECEIVE/FORWARD PAPER TRAY SETTINGS PRINTER CONDITION DOCUMENT FILING CONTROL ADMINISTRATOR SETTINGS The system settings are described in detail on the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 45
configured to allow use of tray 1 in print, copy, and fax modes. To display the next screen, touch the or keys. SYSTEM SETTINGS PAPER TRAY SETTINGS TYPE / SIZE TRAY1 PLAIN / 81/2X11 PRINT COPY DOC. FAX I-FAX FILING OK FIXED PAPER SIDE 1/8 DISABLE DUPLEX DISABLE STAPLE DISABLE PUNCH 2 2-13 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 46
settings, tray settings, and counts. ●Printer test page Shows the PCL symbol set list, fonts, network interface (NIC interface) settings, and settings used for the NIC card. ●Sending address list One touch destination list, group list, program list, and memory box list. ●Document filing user - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 47
low, a message will appear to inform you that the toner cartridge must be replaced. NOTE To view the approximate amount of toner remaining, hold down the [COPY] key during printing or when the machine is on standby. The percentage of toner remaining will appear in the display while you hold down - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 48
STORAGE OF SUPPLIES Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for the finisher. For best copying results, be sure to use only Sharp Genuine Supplies which are designed, engineered, and tested to maximize the life and - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 49
area, fusing area, and exit area (page 2-18) Misfeed in the duplex module (page 2-19) Misfeed in the bypass tray (page 2-19) Misfeed Printing is not possible when a misfeed occurs, and thus any faxes or Internet faxes received at this time will be temporarily held in memory. The faxes will print - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 50
care in removing paper. (Do not touch the metal parts.) 1 Unlatch the duplex module and slide it to the left. Unlatch the module and gently move the module away from the machine. If the machine is not equipped with a duplex module, open the side cover similarly. 2 Remove the misfed paper as shown in - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 51
in the illustrations below. If paper is misfed at the upper part of the duplex module, gently remove it while taking care not to tear the paper. 2 misfed paper during removal. If paper is misfed at the lower part of the duplex module, gently remove it while taking care not to tear the paper. Be - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 52
checking, the partially fed paper may tear and leave torn pieces in the machine, increasing the difficulty of removal. ■ Misfeed in paper tray 1 1 Unlatch the duplex module and slide it to the left. Unlatch the module and gently move the module away from the machine. If the machine is not equipped - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 53
and remove the misfed paper. After removing the misfed paper, be sure to return the paper guide. 5 Gently close the duplex unit. If the machine is not equipped with a duplex module, close the side cover. After closing, confirm that the misfeed message has been cleared and the normal display appears - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 54
REMOVING AN ORIGINAL MISFEED Removing a misfed original from the automatic document feeder If an original misfeed occurs in the automatic document feeder, follow the steps below to remove the misfed original. NOTES ● For misfeed removal in the main unit and other peripheral devices, see page 2-17 ● - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 55
31. For fax, printer, and network scanner/Internet fax problems, see the manuals for those functions. For peripheral device problems, see the explanation of the device. If the message "CALL FOR SERVICE. CODE:**-**"(Note) appears in the touch panel, turn off the power switch, wait about 10 seconds - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 56
TROUBLESHOOTING Problem Check Solution or cause Printing before the finished. stops job is If too many pages collect on the output tray, the tray full sensor activates and stops printing is not set in the paper tray settings of the system settings. When loading paper, if you change the paper - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 57
TROUBLESHOOTING Problem Check Solution or cause Is paper other than SHARPrecommended paper being used? Use SHARP-recommended paper. (Page 2-16) Printed screen contrast using "DISPLAY CONTRAST" in "Default settings" of the system settings. (Page 2-14) Printing takes place on the wrong side of - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 58
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 59
FINISHER 3-7 ● Part names 3-7 ● Specifications 3-7 ● Finisher functions 3-8 ● Using the finisher functions 3-9 ● Staple cartridge replacement 3-10 ● Misfeed in the finisher 3-12 ● Troubleshooting finisher problems 3-13 SADDLE STITCH FINISHER 3-14 ● Part names 3-14 ● Specifications 3-14 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 60
duplex modules are available: duplex module/bypass tray and duplex module. The descriptions in this manual are for the duplex module/bypass tray. For information on misfeed removal for these modules, see page 2-19. Part names Exit tray The tray is extendable to support (AR-TE3) Print face down 100 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 61
use paper that has already been printed on by a plain paper fax machine or a laser printer. This may cause printed images to become dirty. ● Do not use paper several times before loading. 4 Set the type and size of the loaded paper. When the paper system is changed from the inch system to the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 62
service. Problem Check Solution or cause Message indicating the paper type Special paper cannot be used for two-sided cannot be used for two-sided printing printing. Use a paper type adequate for displayed? two-sided printing. (See pages 2-4 and 3-2.) The machine will not print duplex prints - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 63
group of users . Output paper in the copy mode and the fax mode will be delivered to the top tray of the stacker separated from printed output. (Printed output can also be delivered to the top tray.) Part names Top cover Open for misfeed removal. Top tray Output paper from the printer, copier, and - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 64
If a misfeed has occurred in the mail-bin stacker during printing, remove the misfed paper following the procedure below. 1 Open paper, press down on the top cover to close it. 7 Close the paper guide. Close the paper guide securely. 3 If the misfed paper is not found in step 2, open the front - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 65
. Top tray Printer, copier and fax output can be delivered here. To print onto large paper (11" x 17", 8-1/2" x 14", 8-1/2" x 13", A3 or B4), extend the tray. Staple box Pull the box out to replace the staple cartridge or to remove staples. jammed Offset tray Stapled sets or sets to be offset - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 66
mode Groups of prints or copies of the same page will be delivered. Original Printouts Sets will move from side to side so that each set or group will be offset from the previous set or group for easy separation. The offset function can only be used in the offset tray. Stapled sets will not be - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 67
GROUP] key (See page 3-8.) When Group is selected, all copies of the same original will be grouped. (2) [STAPLE SORT] key (See page 3-8.) When Staple Sort is selected, sorted sets will be stapled and delivered to the offset tray. (They will not be offset stacked.) (3) [SORT] key (See page 3-8.) When - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 68
into the staple box aligning the arrow of the staple cartridge with that of the staple box. When reinstalling the staple box, push it in until it clicks into place. 9 Close the front cover. NOTE Make a test print or copy in the staple sort mode to ensure that stapling is performed properly. 3-10 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 69
release lever to the left, rotate the staple unit to face down. When reinstalling the staple box, push it in until it clicks into place. 11Close the front cover. 6 Pull the release lever for the staple box and remove the box. NOTE Make a test print or copy in the staple sort mode to ensure that - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 70
from the output area. Be careful not to tear the misfed paper during removal. 5 Raise the paper guide and remove the misfed paper. Be careful not to tear the misfed paper during removal. Paper guide 2 Open the finisher top cover. Top cover Move the tab in the direction of the arrow as - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 71
. Is a message displayed? "ADD STAPLES" Replace the staple cartridge. (See page 3-10.) Different size paper included? Stapling cannot be performed onto different size paper. Stapled sets are not stacked correctly or some sheets in a set are not stapled. Paper heavily curled? Paper may be - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 72
staple cartridge or to remove jammed staples. Front cover Open the front cover and pull out this section for staple cartridge Stapled print capacity is (6 - 10) sheets x 10 sets or (1 - 5) sheets x 20 sets. Upper tray: 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 73
Specifications are subject to change for improvement without notice. 3 Supplies AR-SC2 staple cartridges must be used for this finisher. The cartridge package contains three cartridges approx. 5000 staples each. Saddle stitch finisher functions ■ Sort mode Sorted sets will be delivered. ■ Group - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 74
mode Collated sets of prints or copies will be stapled and delivered to the offset tray. When saddle stitching is selected, the prints or copies will be stapled at the center and delivered to the saddle stitch tray. The stapling positions, orientation, paper size for stapling, and stapling capacity - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 75
SADDLE STITCH FINISHER ■ Saddle stitch function The saddle stitch finisher can automatically place two staples for centerline binding of prints or copies and fold them along the centerline. 6 4 2 7 9 11 ■ Hole punching (only if a punch module is installed) If the saddle stitch finisher is - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 76
copies of the same original will be grouped. (9) (10) (6) [CENTER TRAY] key If the center tray is selected, output paper will be delivered to the exit tray. (2) [STAPLE SORT] key (See page 3-16.) When Staple Sort is selected, sorted sets will be stapled and delivered to the offset tray. (They will - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 77
Remove the empty staple cartridge. Press the lock button to unlock the staple box cover and remove the staple cartridge. NOTE If staples remain, the staple cartridge cannot be removed. 9 Push the stapler section back into the finisher. 10Close the front cover. NOTE Make a test print or copy in the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 78
SADDLE STITCH FINISHER ■ Staple jam removal 1 Unlatch the saddle stitch finisher and slide it away from the machine. 5 If saddle stitch was selected, open the saddle stitch section cover. 2 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 79
the finisher. 15Close the front cover. 16Push the saddle stitch finisher back against the machine. NOTE Make a test print or copy in the staple sort mode to ensure that stapling is performed properly. 3 Return the punch scrap collecting container to its original position. 2 Pull out the punch scrap - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 80
SADDLE STITCH FINISHER Misfeed in the saddle stitch finisher When a misfeed occurs in the saddle stitch finisher, remove the misfed paper following the procedure below. 1 Press the detach button and separate the saddle stitch finisher from the machine. 5 Remove the misfed paper. Remove the paper - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 81
10Open the front cover. SADDLE STITCH FINISHER 15Push the saddle stitch finisher back onto the machine. 11Rotate roller rotating knob D in the direction of the arrow. Roller rotating knob D 3 12Remove any misfed paper from the saddle stitch tray. Remove the paper gently, taking care not to tear it - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 82
Replace the staple cartridge. (See page 3-19.) Check that a staple cartridge has been installed. (See page 3-20.) Different size paper included? Stapling cannot be performed onto different size paper. Stapled sets are not stacked correctly or some sheets in a set are not stapled. Paper heavily - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 83
network. When a digital multifunction machine that supports Sharp OSA is used, the operation panel controls and functions of the machine such as scan network. A "standard application" refers to all other applications. APPLICATION COMMUNICATION MODULE (MX Applications]. Configure settings for the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 84
display the job log of OSA scan mode, touch the [SCAN] key once again while the job log of scan mode appears in the job status screen. (When this is done, the name of the key will change to [OSA SCAN].) To return to the scan screen from the OSA scan screen, touch the [OSA SCAN] key. 3-26 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 85
MX be kept for each authenticated user. When "external count settings guide). After changing the setting, restart the machine. ■ External count mode When only the [ENABLE EXTERNAL ACCOUNT CONTROL] setting is enabled in "External account setting" of "Sharp OSA settings" in the administrator settings - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 86
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 87
Part 2: Copier Operation - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 88
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 89
A PLACED ORIGINAL 4-5 ● Manually setting the scanning size 4-5 STORING, DELETING, 10 ● Copying from the document glass 4-11 ● Automatic two-sided copying from the document glass 4-13 ADJUSTING THE EXPOSURE 4-14 REDUCTION/ENLARGEMENT/ZOOM 4-15 ● Automatic selection (auto image 4-15 ● Manual - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 90
stapling and duplex will not function and some special functions may not give the expected result. *1 For paper heavier than 28 lbs. (105 g/m2), only a stack of up to 15 sheets can be set. Setting 16 or more sheets may cause incorrect scanning of original and scanned or originals printed with thermal - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 91
size detector size. 2 Adjust the original guides to the size of the originals. NOTES be copied black, causing excessive use of toner. ● Do not place any objects under default setting is "INCH-1". The setting can be changed using "ORIGINAL SIZE DETECTOR SETTING" in the administrator settings - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 92
bottom of the original is positioned as shown in the illustration. If not, staples will be incorrectly positioned and some special features may not give the expected result. . ("Rotation copy setting" can be disabled with a administrator setting. See page 16 of the administrator settings guide.) 4-4 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 93
original detection function is operating. If you have loaded a non-standard size original or wish to change the scanning size, you can follow the steps below to manually set the original scanning size. (For the standard sizes, see "Original size detection function" on page 4-3.) 81/2x11 (A) 0 AUTO - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 94
sizes can be easily called up and are not erased if the power is turned off. Storing a frequently used original size saves you the trouble of manually setting the size each time you copy that size of document. ● To cancel an original size storing, using, or deleting operation, touch the [ORIGINAL - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 95
2R" (A3, B4, A4, A4R, B5, B5R or A5)) are set and the auto paper select function is enabled. READY TO SCAN FOR COPY. If originals of a size other than the sizes above are 1. 81/2x11 PLAIN to be copied, manually 81/2x11 2. 11x17 PLAIN select the desired paper PLAIN 3. 11x17 PLAIN size - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 96
, copying and scanning will stop after the original in progress is output to the original exit area. In these cases the copy quantity will be reset to "0". NOTES ● The 1-sided to 1-sided copying mode is set as the default in the initial settings. If the default setting has not been changed using the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 97
is automatically selected when the original is placed on the document glass. Five sets of copies 5 copies per page 4 ■ Selecting the output tray (when an the appropriate key to select the desired output tray. OUTPUT SORT STAPLE SORT GROUP OFFSET TRAY OFFSET CENTER TRAY 0 OK SADDLE STITCH - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 98
document feeder When the optional duplex module is installed, the following Touch the [2-SIDED COPY] key. SPECIAL MODES 2-SIDED COPY OUTPUT 4-10 If a copy key is touched for a mode that cannot be [BINDING CHANGE] key. 4 Touch the [OK] key. 0 OK BINDING Perform steps 6 through 9 on pages - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 99
(A3, B4, A4, A4R, B5, B5R or A5)) are set and the auto paper select function is enabled. READY TO SCAN FOR COPY. If originals of a size other than the sizes above are 1. 81/2x11 PLAIN to be copied, manually 81/ - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 100
default mode. OUTPUT FILE To select sort mode, touch the [OUTPUT] key, touch the [SORT] key in the screen that appears, and then touch the [OK] key. 5 Use the numeric keys to set START] key. Repeat this operation until all originals have been scanned. If you selected "Sort" for the output mode in - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 101
Automatic two-sided copying from the document glass When the optional duplex module is installed, the following automatic two-sided copying can be back side of a two-sided original, touch the [BINDING CHANGE] key. 4 Touch the [OK] key. 0 OK BINDING Perform steps 3 to 7 on pages 4-11 and 4-12. 4-13 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 102
default exposure setting pages 4-7 through 4-10. If the document MANUAL] key to highlight [AUTO], and then touch the [OK] key. ● The exposure level used in automatic exposure mode can be adjusted in the administrator settings. See "Exposure adjustment" on page 16 of the administrator settings guide - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 103
manually. ● Automatic selection: Auto image (see below) ● Manual SELECT] key and then select the desired paper size. READY TO SCAN FOR COPY. 81/2x11 PLAIN 1. 81/2x11 2. 11x17 3. Setting the paper type and paper size" on page 2-5.) NOTE If the message "ROTATE ORIGINAL FROM TO " is displayed, change - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 104
the [ ] key to decrease the ratio. ● Automatic changing of the ratio when a zoom key is continuously touched can be disabled in the administrator settings (see "Key operation setting (prohibit key repeat)" on page 10 of the administrator settings guide). ● If the message "IMAGE IS LARGER THAN COPY - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 105
ORIGINAL AUTO EXPOSURE AUTO 81/2x11 PAPER SELECT Auto paper select display 64% COPY RATIO NOTE If the auto paper select display does not appear all pages of the original have been scanned. (Step 7 on page 4-12) To return the ratio to 100% To return the ratio setting to 100%, touch the [COPY - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 106
]) keys to change the copy ratio in the horizontal (X) direction. 64% Y 10 A fixed ratio key changing of the ratio when a zoom key is continuously touched can be disabled in the administrator settings (see "Key operation setting (prohibit key repeat)" on page 10 of the administrator settings guide - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 107
77% X 50 become highlighted when touched. 64% Y 70 ZOOM 50% 50 Y 77 ZOOM XY ZOOM CANCEL The zoom keys can be used to change the ratio from 25% to 400% in and then press the [START] key. To cancel an X or Y zoom setting... Touch the [XY ZOOM] key or the [CANCEL] key in the ratio selection - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 108
duplex 4-3 to 4-6) 5 Select the bypass tray. READY TO SCAN FOR COPY 81/2x11 P 81/2 x11 11x17 P PLAIN changed the paper type, be sure to change the paper type and size settings as explained in steps 5 to 6 on page 25, and steps 7 to 10 on page 2-6. 4-20 6 Select any desired copy settings - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 109
, storing of copy settings, and other convenient functions Pamphlet copy 5-6 ● Job build 5-8 ● Tandem copy 5-10 ● Covers/inserts 5-12 ● Transparency film with insert sheets shot 5-27 ● Mirror image 5-29 ● B/W reverse 5-29 ● Print menu 5-30 STORING, USING AND DELETING JOB PROGRAMS 5-42 ● - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 110
the main screen. READY TO SCAN FOR COPY. SPECIAL MODES 2- Job build (page 5-8) (6) Tandem copy (page 5-10) (7) [OK] key on the special modes screen B/W reverse (page 5-29) Print menu (page 5-30) General the / keys to change the screen. 2-SIDED Setting procedures for modes requiring setting - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 111
1/2" (10 mm) in its initial setting. This function is convenient when stapling or binding copies with a string. NOTES ● The initial setting for the margin width can be changed in the administrator settings to any value from 0 to 1" (0 to 20 mm). (Page 17 of the administrator settings guide) ● When - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 112
. The erase width is approximately 1/2" (10 mm) in it's initial setting. NOTE The initial setting for the erasure width can be changed in the administrator settings to any value from 0 to 1" (0 to 20 mm). (Page 17 of the administrator settings guide) Original Copy EDGE ERASE Eliminates shadow - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 113
SPECIAL MODES Dual page copy The dual page copy function produces separate copies of two documents placed side by side on the document glass. This function is especially useful when copying books and other bound documents. [Example] Copying right and left pages of a book Book original Dual page - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 114
First page ● When using this function, a duplex module must be installed. ● Scan the originals from the first page to the last finisher is installed, copies can be stapled in two positions along the center MODES The PAMPHLET COPY MARGIN SHIFT setting screen will ERASE appear. The pamphlet - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 115
NO"). PRINT ON size plain paper is loaded. To change the paper tray for the cover, all originals have been scanned. (The next step stapling, select "CONTINUE". To divide the pages into sets that can be stapled, select "DIVIDE". If you performed steps 4 to 6 to insert cover paper, divided stapling - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 116
B in the example) and press the [START] key. Repeat this operation until all sets of originals have been scanned. If you wish to adjust the copy settings each time you place a set of originals, see "Changing the copy settings for each set of originals" on the next page. 5 Touch the [READ-END] key - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 117
the [READEND] key now, copying will begin without scanning the new set of originals. 5 NOTES ● If the original size was set manually at the beginning of the job build procedure, it will not be possible to change the original size setting. If the automatic original detection function is operating - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 118
only be used on the MX-M350N/MX-M450N, or when the network function has been added. Two machines connected to the same network can be used to initial setting (50001). Unless you experience difficulty with this setting, do not change it. The tandem settings should be configured by your network - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 119
is executed for a two-sided copy job with the number of copies set to 999 and "Non- staple" is selected, tandem copying will take place. (2) If tandem copying in the client machine and 5 the job will be printed when the client machine is able to print. ● If auditing mode is enabled on both the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 120
can be disabled in the administrator settings (page 11 of the administrator settings guide). Example of adding covers Example of 47 to 4-10. When these settings have been completed, perform the procedure to select covers/inserts on the following page. ● The original must be scanned from the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 121
You will return to the screen of above. 4 Touch the [FRONT COVER] key in the screen of step 2. 5 Set the insertion conditions for the front cover paper. PLEASE SET UP A FRONT COVER. FRONT COVER SETTING PRINT ON FRONT COVER YES NO 1-SIDED CANCEL 0 OK PAPER TRAY 2-SIDED TRAY2 81/2x11 PLAIN - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 122
screen (2nd screen). 5 Set the insertion conditions for insertion type A . INSERTION TYPE A SETTING PRINT ON INSERT SHEETS YES NO only applies to insertion type B paper.) The [2-SIDED] key appears when the duplex module is installed. (3)The (Z) key shows the tray selected for insertion type - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 123
] key to specify the pages where you wish to insert the insert papers of [INSERTION TYPE A SETTING] and [INSERTION TYPE B SETTING]. CANCE RTION SETTING TION SETTING INSERTION SETTINGS 9 Touch the [INSERTION TYPE A] key or the [INSERTION TYPE B] key, enter the page number where you wish to insert - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 124
SETTING CANCEL OK INSERTION SETTINGS PAPER TRAY SETTINGS PAGE LAYOUT CANCEL DELETE AMEND 2 The set covers/inserts pages are shown. PAGE LAYOUT FRONT COVER INSERTION TYPE A - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 125
the explanations easier to understand. The numbers that appear indicate relations between the originals and copies, and will vary depending on the settings. Type Symbol Meaning Icon appearing in display Front cover when not copied on. Type Symbol Meaning Icon appearing in display Insert - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 126
SPECIAL MODES ■ Covers (One-sided copying of one-sided originals) One-sided copies are made of the following one-sided originals. 1st page 2nd page 3rd page 4th page 5th page 1 2 3 4 5 6th page 6 Copying on cover Front cover Back cover No copying No copying Resulting copies 1 2 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 127
SPECIAL MODES ■ Covers (Two-sided copying of one-sided originals) Two-sided copies are made of the following one-sided originals. 1st page 2nd page 3rd page 4th page 5th page 1 2 3 4 5 6th page 6 Copying on cover Front cover Back cover No copying No copying 2 Resulting copies 1 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 128
SPECIAL MODES ■ Covers (One-sided copying of Two-sided originals) One-sided copies are made of the following two-sided originals. 1st page 2nd page 3rd page 1 3 5 6 4 2 Copying on cover Front cover Back cover No copying No copying Resulting copies 1 2 3 4 5 6 6 One-sided 1 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 129
■ Covers (Two-sided copying of two-sided originals) Two-sided copies are made of the following two-sided originals. 1st page 2nd page 3rd page 1 3 5 6 4 2 6 6 Copying on cover Front cover Back cover No copying No copying 2 Resulting copies 1 3 5 4 6 One-sided 1 3 5 4 No - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 130
one-sided originals) One-sided and two-sided copying is performed using the following one-sided originals. The insertion page of the insert is set to page 3. 1st page 2nd page 3rd page 4th page 5th page 6th page 1 2 3 4 5 6 6 Copying on insert 1 No copying Resulting copies (one-sided - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 131
DUPLEX DISABLE STAPLE DISABLE PUNCH 6 Touch the [TYPE/SIZE] key. PER TRAY SETTINGS TYPE / SIZE TRAY 2 PLAIN / 81/2x11 5 PRINT COPY DOC. FAX I-FAX FILING 3 Touch the [PAPER TRAY SETTINGS] key. The paper tray selection RINT PAPER TRAY screen will appear. SETTINGS ATA ORWARD PRINTER - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 132
for the insert paper. OK CANCEL OK PRINT ON INSERT SHEETS YES NO INSERTION SHEET TRAY5 document feeder is being used, see pages 4-7 through 4-10. If the document glass is being used, see pages , the appropriate copy ratio will be automatically set based on the original size, paper size, - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 133
follow If an automatic document feeder is being used, see pages 4-7 through 4-10. If the document glass is being used, see pages 4-11 through 4-13. cancel the multi shot function, touch the [CANCEL] key in the multi shot setting screen (the screen of step 2). 3 Select the layout. 5 OK Select the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 134
The two pages of the open book are scanned as a set, and two pages each are copied onto ● When using this function, a duplex module must be installed. ● Scan the originals from the first page be used in combination with the pamphlet function to staple and fold the copies at the centerline. To - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 135
the [PAPER SELECT] key and then select the desired paper size. READY TO SCAN FOR COPY. 81/2x11 PLAIN 1. 81/2x11 2. 11x17 3. 11x17 4. initial settings configured in the administrator settings, touch the [SIZE RESET] key. (See "CARD SHOT SETTINGS" on page 17 of the administrator settings guide). ● - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 136
step 5). 9 Press the [START] key. The back side of the card is scanned. 5 Place the original on the document glass. Place the front side of the 4-12). 7 Press the [START] key. The front side of the card is scanned. 10Touch the [READ-END] key. NOTE The original must be placed on the document - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 137
setting (page 4-14) automatically changes to "Text". ● Originals with large black areas (which use a large amount of toner) can be printed with black/white reverse to reduce toner automatic document feeder is being used, see pages 4-7 through 4-10. If the document glass is being used, see pages 4-11 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 138
you wish to print a file saved in copy mode and use a print menu setting, use the special modes in the Job settings / print screen (or the document filing print screen in the Web page if the machine is connected to a network) to select the print menu setting. (A print menu setting cannot be selected - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 139
position appear as follows depending on the state of the setting: Not selected, print menu setting has not been selected. Selected during selection of the print menu setting. Not selected, print menu setting has already been selected. The image displayed within each key varies depending on the key - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 140
. The position can be changed and settings canceled if needed. 9 Touch the [OK] key on the print menu setting screen. 10Touch the [OK] key on the special modes screen. About the steps that follow If an automatic document feeder is being used, see pages 4-7 through 4-10. If the document glass is - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 141
OK The date to be printed CURRENT SETTING 2010/APR/04 FIRST PAGE is displayed in "CURRENT SETTING" in the selected format. DATE CHANGE ALL PAGES The date that appears is the date set in the machine. If you need to change the date, touch the [DATE CHANGE] key. The following screen appears - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 142
selected stamp is highlighted. If the desired stamp does not appear, change screens with the or key. 4 Adjust the exposure as needed step 4 of "Common operation procedure for using the print menu" (page 5-31). NOTE To cancel a stamp setting... Touch the [CANCEL] key in the stamp selection - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 143
NUMBERING TEXT OK OK 1/2 4 If you need to change the starting or ending number of page numbering, the first page printed on, or the print settings for covers/inserts, touch the [PAGE NUMBER] key. CANCEL OK TOTAL PAGE AUTO MANUAL PAGE NUMBER 3 Select the page number format. PAGE NUMBERING - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 144
MANUAL PAGE NUMBER 11Continue from step 4 of "Common operation procedure for using the print menu" (page 5-31). NOTE To cancel a page number setting... Touch the [CANCEL] key in the page number selection screen. (The screen of step 10 the date does not change. Print settings Front Back Date - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 145
SHEET AUTO 1 ABCD 1/4 2/4 3/4 4/4 COUNT FRONT COVER Not selected PRINTING STARTS FROM SHEET: 2 Not printed Not printed 1/3 2/3 3/3 Printed contents when settings are changed COUNT FRONT COVER: Selected Not printed (count) 2/5 3/5 4/5 5/5 as follows COUNT FRONT COVER: Selected - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 146
FRONT COVER Not selected Printed PRINTING STARTS Not Not Not Not Not Not FROM SHEET: 3 printed printed printed printed printed printed 1/4 contents when COUNT FRONT Not printed Not printed COVER: Selected (count) (count) 3/10 4/10 5/10 6/10 7/10 settings are changed as follows COUNT - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 147
network, the printed set to show 6 keys per screen. This can be changed to 3 keys per screen by touching the [3 6] key. When 3 keys are displayed, the entire text sequence will appear in each key. (When 6 keys are displayed, up to 22 characters appear in each key.) 6 Select the pages to be printed - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 148
2 of "Common operation procedure for using the print menu" (page 5-31). 2 Touch the [ the [STORE/DELETE] key. PRE-SET RECALL STORE/DELETE PRE-SET RECALL STORE/DELETE 4 Touch a key close the character entry screen. If no free keys appear, change screens with the or key. 5 Touch the [BACK] - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 149
. (Go to step 6.) The keys indicating the print position appear as follows depending on the state of the setting: Print position without any set print menus. Currently set print position. Print position with another competing print menu set. (When moving a stamp, this indicates that another - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 150
The selected settings will be stored in the number key selected in step 3. AUTO M NUMBER. RECALL STORE/DELETE 3 Touch the number key ([1] to [10]) in which a job program. (See page 17 of the administrator settings guide.) 4 Select the copy settings that you wish to store in the job program. TO - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 151
program has been stored is selected, the screen will change to the screen of step 4 on the STORE/DELETE previous page for settings has been prohibited in the administrator settings, it will not be possible to store or delete a job program. (See page 17 of the administrator settings guide - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 152
the interrupt original is being scanned or while you are selecting copy settings, touch the [CANCEL] key entered account number. ● If a copy is being printed when the [INTERRUPT] key is pressed, interrupt mode , two-sided copying, sort copying, and staple sort copying cannot be selected. If any of - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 153
CHAPTER 6 MACHINE MAINTENANCE (FOR COPYING) This chapter explains procedures for cleaning the machine, and troubleshooting. Page USER MAINTENANCE 6-2 ● Cleaning the document glass and the automatic document feeder ....... 6-2 ● Cleaning the main charger of the photoconductive drum 6-2 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 154
USER MAINTENANCE Cleaning the document glass and the automatic document feeder If the document glass, document cover or automatic document scanning unit have dirty spots, these spots will form lines in scanned images. These will show up as defects when the images are printed solve the problem, pull - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 155
the following troubleshooting list before requesting service as many problems can be fixed by the user. If you are unable to solve the problem by checking the list, turn off the power switch, and unplug the power cord. Problems related to the copy function are described below. For problems related - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 156
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 157
● Scan Save 7-10 CALLING UP AND USING A FILE 7-13 ● Searching for and calling up a saved file 7-13 ● Calling up and using a saved file 7-15 ● File selection screen 7-16 SYSTEM SETTINGS 7-24 ● Creating, editing, and deleting user names and folders 7-24 ENTERING CHARACTERS 7-29 TROUBLESHOOTING - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 158
in copy mode (Quick File saving, page 7-6) Machine hard disk Printing from a computer (printer data, page 7-9) Transmission in fax/image send mode (filing, page 7-7) and Scanning a document only (scan save, page 7-10) Save to machine's hard disk HDD Call up a saved file to reuse it. Machine - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 159
can be assigned. A password can also be set for a saved file ([CONFIDENTIAL] save). (See [Property change] on page 7-21.) If a user name and file name are setting can be selected for files saved with the document filing function. This prevents a file from being moved or automatically or manually - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 160
(4) (5) (6) DOCUMENT FILING IMAGE SEND PRINT READY DATA LINE DATA COPY SYSTEM JOB STATUS SETTINGS LOGOUT (7) (1) Touch panel (see a password or numeric setting. This key is also used to cancel scanning of a document. (6) [CA] key (Clear all key) Use this key to cancel a setting procedure - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 161
Desktop transmission job file 7 Network Folder transmission job file The following icons may appear added to a main icon or alone. Icon Meaning Confidential file or folder Protected file NOTE When the file of a job that was saved using scan save is printed in job settings, the icon of the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 162
printing or transmitting a document in copy mode, printer mode, or fax/image transmission mode, "QUICK FILE" can be selected to save an image of the document to the Quick File folder. The image can be called up at a later time, allowing you to print settings. the warning "THE SCANNED DATA IS STORED IN - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 163
printer mode, or image send mode, "FILE" can be selected to save an image of the document to the main folder or a previously created custom folder. The image can be called up at a later time, allowing you to print USER password has been set for the folder, a password entry screen will appear. Enter - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 164
, CANCEL "-" changes to " ". ENTER PASSWORD VIA THE 10-KEY PAD. 15Touch the [OK] key. You will return to the main screen. 16Press the [START] key on the operation panel. When copying begins, the image is saved. 17The saved image can be called up using the file name, folder name, or user name, or - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 165
SEARCH BACK USER NAME DATE 1 1 User unknown 2003/10/01 User unknown 2003/10/01 PRINTS BATCH P. Touch the key of the file that you wish to call up. A menu screen will appear. If a password is set for the file, a password entry screen will appear. Enter the 5-digit password with the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 166
DOCUMENT FILING IMAGE SEND PRINT READY DATA LINE DATA COPY SYSTEM JOB STATUS SETTINGS 2 Touch the [SCAN TO HDD] key. 6 Perform any of the following steps 7 to 16 as needed. When finished, go to step 17 on page 7-11. ●To set the original size, perform steps 7 to 10. ●To set the resolution, perform - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 167
of step 14. OK MANUAL 17Place the original and scan save procedure. Follow the steps below when you wish to call up the image and print or transmit it. 18The saved image can be called up using the file name, folder name, or user Print the image (page 7-17) ●Transmit the image (page 7-20) ●Change - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 168
fax and network scanner manuals. This also corresponds to the "Multi shot" function in copy mode; however, only 2in1 is possible for scan can be placed in the document feeder at once, this function allows you to scan the pages in sets. (5) [CARD SHOT] key (see page 5-27) This function allows you to - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 169
CALLING UP AND USING A FILE Searching for and calling up a saved file When calling up a file, you can enter the file name, folder name, or user name to quickly search for the file. To search for a file, touch the [SEARCH] key in the main screen of document filing mode or in a - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 170
USER NAME Suzuki Tanaka Kondou DATE 2004/10/20 2004/10/20 2004/10/20 change the order of file display, touch the [FILE OR FOLDER NAME] key, [USER NAME] key, or [DATE] key. If you touch a file name or folder name that has a password, a password entry screen will appear. Enter the 5-digit password - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 171
: Print the file (page 7-17). ● [Send] : Transmit the saved file (page 7-20). The file can be transmitted by Scan to E-mail, Scan to FTP, Scan to Network Folder, fax, or Internet fax. (All of these methods require installation of the appropriate options.) (Page 1-11) ● [Property change] : Change the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 172
ALL FILES CUSTOM FOLDER SEARCH BACK USER NAME Yamada Sato Akata DATE 1 3 2006/10/20 2006/10/20 2006/10/20 BATCH P. (4) (1) When a file is touched, the job setting screen appears. (2) [File Name] key, [User Name] key, [Date] key Use these keys to change the order of display of the file - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 173
two-sided printing, the optional duplex module is necessary. (4) [TANDEM PRINT] key If the conditions for tandem printing are met (page 5-10), touch this key to enable tandem printing. See page 5-10 for more information. When printing a file that was saved in copy mode, this key changes to the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 174
a password, go to the next step. 5 To set the number of copies, touch the [CHANGE PRT.NO.] key. CHANGE PRT.NO. If you wish to use the number of copies stored with each file, go to step 9. NT AND DELETE THE DATA 3 Touch the user name of the files that you wish to print by batch printing - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 175
you will return to the file list screen. NOTES ● If "Auditing mode" is enabled in the administrator settings for copy mode, print mode, or document filing mode, it will not be possible to perform batch printing of [ALL FILES]. ● To display the job tab of a mode for which "Auditing mode" is enabled - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 176
ADDRESS ENTRY ADDRESS BOOK ADDRESS REVIEW SEND SETTINGS SPECIAL MODES SEND (7) (8) (9) (10) (1) [RESOLUTION] key Use this key to set the resolution. (2) [FILE FORMAT] key The [FILE FORMAT] key appears in scan mode (Scan to E-mail, Scan to FTP, or Scan to Network Folder). Touch this key to - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 177
. Touch this key to set the subject and file name. In scanner mode, the sender name can also be set. (12) [SUB ADDRESS] key or [ADDRESS ENTRY] key ● Touch this key to directly enter the destination for a Scan to E-mail, Scan to FTP, Scan to Network Folder or Internet fax transmission. ● Touch this - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 178
SHARING] and [CONFIDENTIAL] files can be moved. A [PROTECT] file can be moved by first using [PROPERTY CHANGE] to change the attribute to [SHARING] or [CONFIDENTIAL]. JOB SETTINGS / MOVE Basic specifications Yamada Taro SELECT THE FOLDER THE FILE IS MOVED TO. FILE NAME Basic specifications 8A1 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 179
09 00 touch the key or COPY 13:27 12/09 00 key to change screens. The touched key is highlighted. DETAIL OF COPY FILE NAME: SIZE:81/2x11 COPY_20041021_153050 RESOLUTION:600x600dpi DATE:2004/10/10 15:30 PAGES:10 OK CALL 1/2 DETAIL OF COPY FILE NAME COPY_20041021_153050 DATA SIZE: 21,987 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 180
CONTROL] key. TOTAL COUNT DEFAULT SETTINGS ADDRESS CONTROL SENDER CONTROL DOCUMENT FILING CONTROL ADMINISTRATOR USER NAME REGISTRATION CUSTOM FOLDER REGISTRATION AMEND/DELETE USER NAME AMEND/DELETE CUSTOM FOLDER (3) (4) (1) [USER NAME REGISTRATION] key Program a user name. (See the next - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 181
. PASSWORD SELECT THE DEFAULT FOLDER THE FIL STORED TO: 4 Set a password for the user name (enter a 5-digit password with the numeric keys). This will be the password for CANCEL the user name entered in step 1. ENTER PASSWORD VIA THE 10-KEY PAD. As each digit is entered, "-" changes to - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 182
NOTE When a user name is changed, the change is not updated to any previously saved data (files or folders). After entering the password, the following screen will appear. USER NAME / AMEND/DELETE No.001 USER NAME Yamada DELETE EXIT INITIAL Yamada PASSWORD SELECT THE DEFAULT FOLDER THE FILE - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 183
be omitted. If you are omitting a INITIAL PASSWORD password, go to step 6. USER NAME 4 Set a password for the folder (enter a 5digit password with the numeric keys). This will be the password CANCEL for the folder name entered in step 1. ENTER PASSWORD VIA THE 10-KEY PAD. 5 Touch the [OK] key - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 184
the [NEXT] key, a new folder SWORD screen will appear. Repeat steps 1 to 10 to create a new folder. ■ Editing/deleting a custom folder To edit a previously created folder (change the folder name, initial, password, or user name), or to delete a folder, follow steps 1 and 2 on page 7-24 and - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 185
or edit characters in setting screens such as auto dial key programming screens, follow the steps below. Characters that can be entered are alphabetical characters, special characters, numbers, and symbols. ■ Entering alphabetical characters (Example: Sharp äÄ) 1 Touch the [S] key. 5 Touch - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 186
, it may not be possible to use spaces and the symbols indicated below. For example, hyperlinks will not operate correctly or nonsense characters may appear. Change screens by touching the key or key displayed in the screen. If you make a mistake, touch the key to move the cursor ( ) back one - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 187
problems, fax problems, and network scanner problems, please see the troubleshooting sections of the appropriate manuals. Problem Check Cause and solution A saved file has Was the file called up and then printed by A file that is printed using the [PRINT AND disappeared. touching the [PRINT - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 188
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 189
CHAPTER 8 SPECIFICATIONS This chapter contains useful information about the machine. Page SPECIFICATIONS 8-2 LIST OF COMBINATION OF PERIPHERAL DEVICES 8-4 INDEX ...8-5 8-1 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 190
or 8 mm (leading edge and trailing edge in total), max. 21/64" or 8 mm (along all other edges in total) 80 seconds or less MX-M350N/MX-M350U : 4.9 seconds or less* MX-M450N/MX-M450U : 4.4 seconds or less* * Conditions: The document glass is used and A4 size paper is fed horizontally from the machine - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 191
) MX-M350N/MX-M350U MX-M450N/MX-M450U Copy paper size 100% / Reduced / Enlarged 11" x 17" (A3) 17 copies/min. 20 copies/min. 8-1/2" x 14" (B4) 20 copies/min. 22 copies/min. 8-1/2" x 11" (A4) 35 copies/min. 45 copies/min. 8-1/2" x 11"R (A4R) 25 copies/min. 30 copies/min. 7-1/4" x 10 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 192
functional and some cannot be installed together (A). (B) Multi purpose drawer Stand/3 x 500 sheet paper drawer Stand/MPD & 2000 sheet Duplex module/bypass tray Duplex module Saddle stitch finisher Finisher Mail-bin stacker Exit tray Upper exit tray extension Punch unit (A) Related to paper feed - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 193
-Setting originals 4-3 -User maintenance 6-2 Automatic exposure adjustment 4-14 Automatic selection 4-15 Automatic two-sided copying -Automatic document feeder 4-10 -Document glass 4-13 Automatic two-sided printing 2-4 ■B B/W reverse 1-6, 5-2, 5-29 Barcode font kit 1-12 Binding change 4-10 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 194
2-17 Installation requirements 0-3 Interior 1-10 Internet fax expansion kit 1-12 [INTERNET-FAX] key 1-16 Interrupting a copy Network expansion kit 1-12 Network scanner expansion kit 1-12 Non-standard sizes 2-3, 2-5, 2-6, 4-5 Number of pages printed 1-18 number of pages transmitted (scanned - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 195
Printer test page 2-14 [PRIORITY] key 1-16 Proper storage 2-16 Protect 7-3 PS3 expansion kit 1-12 Punch module 3-15 [PUNCH] key 3-18 ■Q Quick File folder 7-3 [QUICK FILE FOLDER] key 7-5 [READ-END] key 4-12 ■R Reduction 4-15 Reduction/Enlargement 1-4, 4-15 Replacing the toner cartridges - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 196
2-23, 6-3 Toner cartridge 1-10, 2-15 Top cover 3-5, 3-7, 3-14 Top tray 3-5, 3-7 Total count 2-14 Total number of originals 4-2 Touch panel 1-13, 1-14, 7-4, 7-5 Transparency film 2-3, 2-4, 2-10, 4-20, 5-23 Transparency inserts 1-5, 5-2, 5-23 Tray 1-9 Troubleshooting -Copier operation - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 197
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 198
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 199
DEALER ABOUT THE WARRANTY THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of warranty protection, Sharp extends a limited warranty to each of its authorized dealers and, in turn, requires each of its authorized dealers to extend its own warranty to you - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 200
MX-M350U/MX-M450U/MX-M350N/MX-M450N OPERATION MANUAL (for general information and copier operation) SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-1163. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 This manual has - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 201
ADMINISTRATOR SETTINGS GUIDE LASER PRINTER This manual explains settings for use by the administrator of the machine. Page • PURPOSE OF THE ADMINISTRATOR SETTINGS 1 • ADMINISTRATOR SETTINGS LIST 3 • USING THE ADMINISTRATOR SETTINGS 4 • GENERAL SETTINGS 7 • COPY SETTINGS 16 • - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 202
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 203
●Printer Operation manual (for printer), chapter 6 ●Fax Operation manual (for facsimile), chapter 8 ●Network scanner / Internet fax Operation manual (for image send), chapter 8 To access the administrator settings, the administrator password must be entered. * Can only be used on the MX-M350N/MX - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 204
scan-saved image file pages that can be printed. Setting an administrator password The administrator password is a 5-digit number that must be entered in order to access the key operator programs. The administrator of the machine should change the factory default administrator password that was set - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 205
IPsec 14 List print 14 Sharp OSA settings Default display setting 14 External account setting 14 Change admin password 14 Product key PS3 expansion kit 15 Network scanner expansion kit 15 Internet fax expansion kit 15 E-mail alert and status 15 Network expansion kit 15 Data - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 206
is entered, the dashes (-) ADMINISTRATOR PASSWORD in the display will change to asterisks ( ). The factory default setting for the key operator code number is 00000. 4 Touch the [CHANGE ADMIN PASSWORD] key . NGS PRINTER SETTINGS CHANGE ADMIN PASSWORD If you wish to configure a different - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 207
screens that require the entry of numerical values. OK 20 (1 999) A ORIGINAL SIZE DETECTOR SETTING DISABLING OF DOCUMENT 1/2 FEEDER DISABLING OF DUPLEX DISABLING OF LARGE CAPACITY CASSETTE C B DISABLING OF STAPLER DISABLING OF PUNCH D E A When a key that appears in the form XXX - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 208
TANDEM SETTING PING COMMAND SSL SETTING ENABLE IPsec LIST PRINT Sharp OSA SETTINGS DEFAULT DISPLAY SETTING EXTERNAL ACCOUNT SETTING CHANGE ADMIN PASSWORD PRODUCT KEY PS3 EXPANSION KIT DATA SECURITY KIT NETWORK SCANNER EXPANSION KIT APPLICATION INTEGRATION MODULE INTERNET FAX EXPANSION KIT - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 209
per account This setting is used to display or print the total number of pages printed by each account. Misfed paper is not counted. When using the network scanner feature and fax feature, the number of transmitted pages can also be displayed or printed. (Touch the [IMAGE SEND] key to change screens - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 210
, touch the [IMAGE SEND] key and then enter limits for fax send, scanner and Internet fax send. If you enter the number of an account that already has a limit set, the limit will appear in the limit display. Press the [C] key to change the limit to a hyphen (-), and then enter a new limit. When - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 211
without use of the dedicated printer driver. If the printer driver is used, the printer driver setting will override this setting.) Print data Example of print in the toner save mode Toner save in copy mode This setting is used to save toner in copy mode. This setting functions the same way as - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 212
screen of copy mode Exposure adjustment screen in main screen of fax, Internet fax, Exposure level3 and network scanner modes (middle level) Exposure adjustment screen in [SCAN TO HDD] in main screen of document filing mode Auto clear setting If the machine is not used for a certain duration of - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 213
, scanning can still be performed using the document glass. Disabling of duplex This setting is used to disable duplex printing when the duplex module malfunctions. When this settings is enabled, only one-sided printing can be performed. Disabling of stapler This setting is used to disable stapling - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 214
plug is unplugged while optimization is in progress, the hard drive may be damaged and stored data or received data may be lost. NOTES ● About stopped jobs Printing of received faxes and Internet-Faxes and transmission of stored fax jobs will automatically resume after the machine restarts. For - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 215
you wish to have two machines (which are used as TCP/IP network printers) print in tandem. The factory default setting for the port number is [50001]. Unless you experience difficulty with this setting, it does not need to be changed. The tandem function can also be prohibited, or the reception of - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 216
, printer, fax/image send, document filing, general, security, all administrator settings lists • Touch a key other than the [ADMINISTRATOR SETTINGS LIST] key to begin printing a list or report. Sharp OSA settings The following settings are related to Sharp OSA. Touch the [Sharp OSA SETTINGS] key - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 217
to be used as a PostScript compatible printer). Ask your dealer for the product key. Network scanner expansion kit This setting is used to enter the product key for the network scanner expansion kit. Ask your dealer for the product key. Internet fax expansion kit This setting is used to enter the - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 218
changed default settings to the initial factory default settings. Defaults for the following copy settings can be changed: Paper tray/Exposure tray/Copy ratio/2-sided copy/Out put (auto, sort, staple sort, group, output tray) NOTE If this setting is used to change the default setting for the duplex - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 219
widths are normally set to 1/2" (10 mm). Card shot settings This setting is used to set the initial set to 999. Disabling deletion of job programs This setting is used to prohibit the deletion and changing of copy settings stored in job programs. Disabling of bypass-tray in duplex copy This setting - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 220
cannot be printed from the [JOB SETTINGS] screen. • Similarly, the [SCAN SEND], [FAX SEND], and [I-FAX SEND] keys control the corresponding transmission operations in the [JOB SETTINGS] transmission screen. Administrator authority setting When a password has been established for a file, user name or - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 221
to change the default exposure level for "SCAN TO HDD" of the document filing function. The default exposure is initially set to "AUTO". If changed to "MANUAL", the exposure level can be adjusted to five levels. Level 1 is the lightest level and level 5 is the darkest level. Batch print settings - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 222
20 - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 223
Contact at: ✂ Information that the administrator of the machine requires is printed on the back of this page. (Separate this page from the manual and keep it in a safe place. In addition, fill in the name of the administrator and the administrator's contact information in the left hand margin.) - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 224
in the Web pages. A person who logs in as a "User" can only configure certain settings. The factory default passwords are shown below. User Administrator Factory default account user admin Factory default password Sharp Sharp Forwarding all transmitted and received data to the administrator - Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 225
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 226
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 227
- Sharp MX-450U | MX-M350U | MX-M450U | MX-M350N | MX-M450N Operation Manual - Page 228
MX-M350U/MX-M450U/MX-M350N/MX-M450N ADMINISTRATOR SETTINGS GUIDE SHARP ELECTRONICS CORPORATION 1 Sharp Plaza, Mahwah, New Jersey 07430-1164. www.sharpusa.com SHARP ELECTRONICS OF CANADA LTD. 335 Britannia Road East, Mississauga, Ontario, L4Z 1W9 This manual has been printed using a vegetable-based
![](/manual_guide/products/sharp-mx450u-mxm350u-mxm450u-mxm350n-mxm450n-operation-manual-9522b59/1.png)
PART 1: GENERAL INFORMATION
•
BEFORE USING
THE PRODUCT
•
MANAGING THE MACHINE
•
PERIPHERAL DEVICES
PART 2: COPIER OPERATION
•
MAKING COPIES
•
CONVENIENT COPY
FUNCTIONS
•
MACHINE MAINTENANCE
(FOR COPYING)
•
DOCUMENT FILING
FUNCTION
•
SPECIFICATIONS
1-1
2-1
3-1
4-1
5-1
6-1
7-1
8-1
Page
OPERATION MANUAL
(for general information and copier operation)
MODEL
MX-M350U
MX-M450U
MX-M350N
MX-M450N
LASER PRINTER
Be sure to become thoroughly familiar with this manual to
gain
the
maximum
benefit
from
the
product.
Before installing this product, be sure to read the
installation requirements and cautions sections.
Be sure to keep all operation manuals handy for reference
including this manual, the "Operation manual (for general
information and copier operation)" and operation manuals
for any optional equipment which has been installed.