Singer Fashion Mate 3342 Instruction Manual and Troubleshooting Guide - Page 12

Winding the Bobbin

Get Singer Fashion Mate 3342 PDF manuals and user guides View all Singer Fashion Mate 3342 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

2 GETTING READY TO SEW Winding the Bobbin ¤ This machine uses SINGER® Class 15 transparent bobbins. Use only this style of bobbin when purchasing additional bobbins for your machine. Do not substitute with metal bobbins. 4 1. Place thread spool and corresponding size spool holder onto spool pin. Spool holder should be large enough to cover the end of the thread spool so thread unreels smoothly. For smaller, narrower spools, use the small spool cap, which can be found in the removable storage compartment. A C 2. (A) Snap thread into guide at top of machine. (B) Place thread snuggly around bobbin winding tension disk to ensure that thread winds onto bobbin smoothly and consistently. (C) Thread bobbin as shown, then place it onto the bobbin winding spindle. B A B 3. &KHFNWKDWEREELQLVSXVKHGGRZQ¿UPO\ $  If it is not, the thread could begin winding under the bobbin. Push the bobbin and spindle ¿UPO\WRWKHULJKW %  4. Hold the thread end to get ready to wind. Step on the foot control gently as you hold the thread end. Allow it to wind a few revolutions slowly, then remove your foot from the foot control to stop. 5. Trim the thread end close to the top of the bobbin, then resume winding by stepping on the foot control. A B 6. The bobbin will stop winding when it is full. Lift your foot off the foot control. Push the bobbin to the left (A), then trim the thread and remove the bobbin from the spindle (B). 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
GETTING READY TO SEW
2
2
12
Winding the Bobbin
A
B
C
B
A
A
B
¤
This machine uses
SINGER
®
Class 15 transparent bobbins.
Use only this style of bobbin when purchasing additional bobbins for your machine.
Do not substitute
with metal bobbins.
1. Place thread spool and corresponding size
spool holder onto spool pin. Spool holder
should be large enough to cover the end of the
thread spool so thread unreels smoothly.
For
smaller, narrower spools, use the small spool
cap, which can be found in the removable
storage compartment.
2.
(A) Snap thread into guide at top of machine.
(B) Place thread snuggly around bobbin
winding tension disk to ensure that thread
winds onto bobbin smoothly and consistently.
(C) Thread bobbin as shown, then place it onto
the bobbin winding spindle.
3.
&KHFN WKDW EREELQ LV SXVKHG GRZQ ¿UPO\ ³$¶±
If it is not, the thread could begin winding
under the bobbin. Push the bobbin and spindle
¿UPO\ WR WKH ULJKW ³%¶±
4.
Hold the thread end to get ready to wind.
Step on the foot control gently as you hold the
thread end. Allow it to wind a few revolutions
slowly, then remove your foot from the foot
control to stop.
5.
Trim the thread end close to the top of the
bobbin, then resume winding by stepping on
the foot control.
6.
The bobbin will stop winding when it is full. Lift
your foot off the foot control. Push the bobbin
to the left (A), then trim the thread and remove
the bobbin from the spindle (B).
4