Singer Heavy Duty 6800C User Manual - Page 16

Wind the Bobbin, Remove the bobbin cover A by pushing the small button

Get Singer Heavy Duty 6800C PDF manuals and user guides View all Singer Heavy Duty 6800C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Wind the Bobbin A C B 1. Place the thread spool on the spool pin. Slide a spool cap firmly against the spool. 2. Place the thread into the thread guide (A) from front to the back. Bring the thread clockwise around the bobbin winding tension disc, making sure that the thread is pulled snuggly between the discs. 3. Thread through the hole in the bobbin (C) from the inside to the outside. 4. Place the bobbin on the bobbin winding spindle. Make sure the bobbin is pushed down firmly. 5. Push the bobbin winding spindle to the right. Hold the thread end, and press the foot control to start winding. After a few turns, take your foot off the foot control to stop winding. Cut the excess thread tail above the bobbin, making sure to trim it close to the bobbin. Step on the foot control to resume winding. When the bobbin is full, the bobbin winding will slow down and stop automatically. Note: You can also start the winding by long pressing the start/stop button. When the winding spindle is pushed to the right, a bobbin winding icon is shown on the display (D). 6. Push the bobbin winding spindle to the left. Remove the bobbin and cut the thread. Note: When the bobbin winding spindle is pushed to the right, the machine will not sew. Make sure to push the bobbin spindle back to the sewing position (left) before sewing. Insert the Bobbin Note: Make sure that the needle is fully raised and the 1 machine is turned off before inserting or removing the bobbin. 1. Remove the bobbin cover (A) by pushing the small button to the right of the cover (B) towards the right. 2. Insert the bobbin in the bobbin case with the thread running in a counterclockwise direction. 3 3. With the tip of your finger on the bobbin, pull the thread slightly to the right and under the guide (C) then towards the left. Continue guiding the thread up toward the left and around the curve (D). Bring it down the channel toward the front and into the bobbin thread knife (E). 4. Replace the bobbin cover and pull the thread to the right to 5 cut off the excess thread. 2 A B 4 C D E 12 - Preparations English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Wind the Bobbin
A
B
C
1.
Place the thread spool on the spool pin. Slide a spool cap
firmly against the spool.
2.
Place the thread into the thread guide (A) from front to the
back. Bring the thread clockwise around the bobbin
winding tension disc, making sure that the thread is pulled
snuggly between the discs.
3.
Thread through the hole in the bobbin (C) from the inside
to the outside.
4.
Place the bobbin on the bobbin winding spindle. Make sure
the bobbin is pushed down firmly.
5.
Push the bobbin winding spindle to the right. Hold the
thread end, and press the foot control to start winding.
After a few turns, take your foot off the foot control to stop
winding. Cut the excess thread tail above the bobbin,
making sure to trim it close to the bobbin. Step on the foot
control to resume winding. When the bobbin is full, the
bobbin winding will slow down and stop automatically.
Note: You can also start the winding by long pressing the
start/stop button.
When the winding spindle is pushed to the right, a bobbin
winding icon is shown on the display (D).
6.
Push the bobbin winding spindle to the left. Remove the
bobbin and cut the thread.
Note: When the bobbin winding spindle is pushed to the right, the machine will not sew. Make sure to push the bobbin spindle back
to the sewing position (left) before sewing.
Insert the Bobbin
A
B
1
2
3
C
D
4
5
E
Note: Make sure that the needle is fully raised and the
machine is turned off before inserting or removing the bobbin.
1.
Remove the bobbin cover (A) by pushing the small button
to the right of the cover (B) towards the right.
2.
Insert the bobbin in the bobbin case with the thread
running in a counterclockwise direction.
3.
With the tip of your finger on the bobbin, pull the thread
slightly to the right and under the guide (C) then towards
the left. Continue guiding the thread up toward the left and
around the curve (D). Bring it down the channel toward the
front and into the bobbin thread knife (E).
4.
Replace the bobbin cover and pull the thread to the right to
cut off the excess thread.
12 – Preparations
English