Smeg STFABURD-1 Instruction Manual 2 - Page 16

is visualized at the end of the cycle that comes, however

Get Smeg STFABURD-1 PDF manuals and user guides View all Smeg STFABURD-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

EN USER INSTRUCTIONS FAULT E6 E7 E8 E9 E11 Light off DESCRIPTION Water pump-out malfunction The appliance does not pump out the water or does so incorrectly. Make sure the drain hose is not kinked or crushed and that the siphon and filters are not clogged. If the problem persists, contact the technical assistance service. Turbine flow-regulator malfunction (only for models fitted with this feature) The appliance is unable to precisely measure the quantity of incoming water. Interrupt the current program and switch off the dishwasher. Switch it back on again, program a new cycle and press start. If the problem persists, contact the technical assistance service. Alternate washing system malfunction Interrupt the current program and switch off the dishwasher. Switch it back on again, program a new cycle and press start. If the problem persists, contact the technical assistance service. Water intake system malfunction Contact the technical assistance service. Wash motor pump does not work Tab. 4-01a Light on Light flashing If an alarm occurs the appliance interrupts the program in progress and signals a fault. • Alarms E1, E2, E3, E4, E8 and E9 interrupt the current program immediately. • The E5, E6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program. • The alarm E7 is visualized at the end of the cycle that comes, however, brought to the end since the operation of the dishwasher is not harmed. • E11: Contact the after-sales service. To "reset" an alarm is necessary: Open and close the door, or turn off and on the machine. At this point is possible to program the dishwasher again. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
16
USER INSTRUCTIONS
EN
FAULT
DESCRIPTION
E6
Water pump-out malfunction
The appliance does not pump out the water or
does so incorrectly. Make sure the drain hose is
not kinked or crushed and that the siphon and
filters are not clogged.
If the problem persists, contact the technical as-
sistance service.
E7
Turbine flow-regulator malfunction
(only for models fitted with this feature)
The appliance is unable to precisely measure the
quantity of incoming water. Interrupt the current
program and switch off the dishwasher. Switch it
back on again, program a new cycle and press start.
If the problem persists, contact the technical assis-
tance service.
E8
Alternate washing system malfunction
Interrupt
the
current
program
and
switch
off
the dishwasher. Switch it back on again, program
a new cycle and press start. If the problem per-
sists, contact the technical assistance service.
E9
Water intake system malfunction
Contact the technical assistance service.
E11
Wash motor pump does not work
Tab. 4-01a
Light off
Light on
Light flashing
If an alarm occurs the appliance interrupts the program in progress and
signals a fault.
• Alarms
E1
,
E2
,
E3
,
E4
,
E8
and
E9
interrupt the current program immediately.
• The
E5
,
E6
alarms interrupts the running program once the cause is
resolved, it
will bring bach the execution of the program.
• The alarm
E7
is visualized at the end of the cycle that comes, however,
brought to
the end since the operation of the dishwasher is not harmed.
•
E11
: Contact the after-sales service.
To “reset” an alarm is necessary:
Open and close the door, or turn off and on the machine. At this point is
possible to program the dishwasher again.