Sony BDV-E190 Operating Instructions - Page 42

[Audio Settings

Get Sony BDV-E190 PDF manuals and user guides View all Sony BDV-E190 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

[Frame]: The picture, including subjects that do not move dynamically, is output in high resolution. [Audio Settings] x [BD Audio MIX Setting] [On]: Outputs the audio obtained by mixing the interactive audio and secondary audio to the primary audio. [Off]: Outputs the primary audio only. x [Audio DRC] You can compress the dynamic range of the sound track. [Auto]: Performs playback at the dynamic range specified by the disc (BD-ROM only). [On]: The system reproduces the sound track with the kind of dynamic range that the recording engineer intended. [Off]: No compression of dynamic range. x [Attenuate - AUDIO] Distortion may occur when you listen to a component connected to the AUDIO (AUDIO IN L/R) jacks. You can prevent distortion by attenuating the input level on the unit. [On]: Attenuates the input level. The output level will decrease at this setting. [Off]: Normal input level. x [Audio Output] You can select the output method where the audio signal is output. [Speaker]: Outputs multi-channel sound from the system's speakers only. [Speaker + HDMI]: Outputs multi-channel sound from the system's speakers and 2-channel linear PCM signals from the HDMI (OUT) jack. [HDMI]: Outputs sound from the HDMI (OUT) jack only. Sound format depends on the connected component. • When [Control for HDMI] is set to [On] (page 44), [Audio Output] is set to [Speaker + HDMI] automatically and this setting cannot be changed. • When [Audio Output] is set to [HDMI], the output signal format for the "TV" function is 2-channel linear PCM. x [Sound Effect] You can set the system's sound effects (SOUND MODE setting (page 24)) on/off. For a 2-channel source, you can select [Dolby Pro Logic], [DTS Neo:6 Cinema], or [DTS Neo:6 Music] to simulate surround sound. [Sound Mode On]: Enables the surround effect of the sound mode (page 24). The sampling frequency upper limit is set to 48 kHz. [Dolby Pro Logic]: The system simulates surround sound from 2-channel sources and outputs sound from all the 5.1 channel speakers (Dolby Pro Logic decoding). [DTS Neo:6 Cinema]/[DTS Neo:6 Music]: The system simulates surround sound from 2-channel sources and produces 6.1 channel sound (DTS Neo:6 Cinema/DTS Neo:6 Music mode decoding). [Off]: The sound effects are disabled. You can hear sound as it is recorded. x [Speaker Settings] To obtain the best possible surround sound, set the speakers. For details, see "Setting the Speakers" (page 35). 42US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
42
US
[Frame]: The picture, including subjects that do
not move dynamically, is output in high
resolution.
[Audio Settings]
x
[BD Audio MIX Setting]
[On]
: Outputs the audio obtained by mixing the
interactive audio and secondary audio to the
primary audio.
[Off]: Outputs the primary audio only.
x
[Audio DRC]
You can compress the dynamic range of the
sound track.
[Auto]
: Performs playback at the dynamic range
specified by the disc (BD-ROM only).
[On]: The system reproduces the sound track
with the kind of dynamic range that the
recording engineer intended.
[Off]: No compression of dynamic range.
x
[Attenuate - AUDIO]
Distortion may occur when you listen to a
component connected to the AUDIO (AUDIO
IN L/R) jacks. You can prevent distortion by
attenuating the input level on the unit.
[On]
: Attenuates the input level. The output
level will decrease at this setting.
[Off]: Normal input level.
x
[Audio Output]
You can select the output method where the
audio signal is output.
[Speaker]: Outputs multi-channel sound from
the system’s speakers only.
[Speaker + HDMI]
: Outputs multi-channel
sound from the system’s speakers and 2-channel
linear PCM signals from the HDMI (OUT) jack.
[HDMI]: Outputs sound from the HDMI (OUT)
jack only. Sound format depends on the
connected component.
• When [Control for HDMI] is set to [On] (page 44),
[Audio Output] is set to [Speaker + HDMI]
automatically and this setting cannot be changed.
• When [Audio Output] is set to [HDMI], the output
signal format for the “TV” function is 2-channel
linear PCM.
x
[Sound Effect]
You can set the system’s sound effects (SOUND
MODE setting
(page 24))
on/off.
For a 2-channel source, you can select [Dolby
Pro Logic], [DTS Neo:6 Cinema], or [DTS
Neo:6 Music] to simulate surround sound.
[Sound Mode On]
: Enables the surround effect
of the sound mode (page 24). The sampling
frequency upper limit is set to 48 kHz.
[Dolby Pro Logic]: The system simulates
surround sound from 2-channel sources and
outputs sound from all the 5.1 channel speakers
(Dolby Pro Logic decoding).
[DTS Neo:6 Cinema]/[DTS Neo:6 Music]: The
system simulates surround sound from
2-channel sources and produces 6.1 channel
sound (DTS Neo:6 Cinema/DTS Neo:6 Music
mode decoding).
[Off]: The sound effects are disabled. You can
hear sound as it is recorded.
x
[Speaker Settings]
To obtain the best possible surround sound, set
the speakers. For details, see “Setting the
Speakers” (page 35).