Sony CDX-F5705X Installation/Connections Instructions - Page 1
Sony CDX-F5705X - Fm/am Compact Disc Player Manual
View all Sony CDX-F5705X manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
3-263-701-11 (1) FM/AM Compact Disc Player Installation/Connections Installation/Connexions 2 A SUB OUT (MONO) AUDIO OUT FRONT AUDIO OUT REAR B BUS AUDIO IN BUS CONTROL IN CDX-F5705X © 2004 Sony Corporation Printed in Thailand 1 1 2 3 × 4 4 5 × 2 Equipment used in illustrations (not supplied) Appareils utilisés dans les illustrations (non fournis) Front speaker Haut-parleur avant Power amplifier Amplificateur de puissance Rear speaker Haut-parleur arrière Active subwoofer Caisson de graves actif CD/MD changer Changeur de CD/MD Rotary commander RM-X4S Satellite de commande RM-X4S BUS AUDIO IN Source selector* Sélecteur de source* XA-C30 BUS CONTROL IN * not supplied non fourni Cautions • This unit is designed for negative ground 12 V DC operation only. • Do not get the leads under a screw, or caught in moving parts (e.g. seat railing). • Before making connections, turn the car ignition off to avoid short circuits. • Connect the yellow and red power input leads only after all other leads have been connected. • Run all ground leads to a common ground point. • Be sure to insulate any loose unconnected leads with electrical tape for safety. • The use of optical instruments with this product will increase eye hazard. Notes on the power supply lead (yellow) • When connecting this unit in combination with other stereo components, the connected car circuit's rating must be higher than the sum of each component's fuse. • When no car circuits are rated high enough, connect the unit directly to the battery. Parts Iist (1) • The numbers in the list are keyed to those in the instructions. • The bracket 1 and the protection collar 3 are attached to the unit before shipping. Before mounting the unit, use the release keys 5 to remove the bracket 1 and the protection collar 3 from the unit. For details, see "Removing the protection collar and the bracket (4)" on the reverse side of the sheet. • Keep the release keys 5 for future use as they are also necessary if you remove the unit from your car. Caution Handle the bracket 1 carefully to avoid injuring your fingers. 1 Note Catch Before installing, make sure that the catches on both sides of the bracket 1 are bent inwards 2 mm (3/32 in). If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Connection example (2) Notes (2-A) • Be sure to connect the ground lead before connecting the amplifier. • If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B- ) For connecting two or more CD/MD changers, the source selector XA-C30 (optional) is necessary. Connection diagram (3) 1 To a metal surface of the car First connect the black ground lead, then connect the yellow and red power input leads. 2 To the power antenna control lead or power supply lead of antenna booster amplifier Notes • It is not necessary to connect this lead if there is no power antenna or antenna booster, or with a manually-operated telescopic antenna. • When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes on the control and power supply leads." 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Connecting any other system may damage the unit. 4 To the interface cable of a car telephone 5 To a car's illumination signal Be sure to connect the black ground lead to a metal surface of the car first. 6 To the +12 V power terminal which is energized in the accessory position of the ignition key switch Notes • If there is no accessory position, connect to the +12 V power (battery) terminal which is energized at all times. Be sure to connect the black ground lead to a metal surface of the car first. • When your car has a built-in FM/AM antenna in the rear/side glass, see "Notes on the control and power supply leads." 7 To the +12 V power terminal which is energized at all times Be sure to connect the black ground lead to a metal surface of the car first.