Sony CDX-GT08 Operating Instructions (CDXGT08) - Page 1

4-108-817-11(1) FM/AM Compact Disc Player Owner's Record The model and serial numbers are located on the bottom of the unit. Record the serial number in the space provided below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. CDX-GT08 Serial No. To cancel the demonstration (DEMO) display, see "Adjusting setup items - SET." Para cancelar la pantalla de demostración (DEMO), consulte "Definición de los elementos de configuración - SET". Operating Instructions Manual de instrucciones CDX-GT08 ©2008 Sony Corporation Printed in China For installation and connections, see the supplied installation/connections manual. Warning This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. CAUTION The use of optical instruments with this product will increase eye hazard. For the state of california, USA only Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Perchlorate Material: Lithium battery contains perchlorate Microsoft, Windows Media, and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries. Warning if your car's ignition has no ACC position Be sure to set the Auto Off function. The unit will shut off completely and automatically in the set time after the unit is turned off, which prevents battery drain. If you do not set the Auto Off function, press and hold until the display disappears each time you turn the ignition off. Welcome ! Thank you for purchasing this Sony Compact Disc Player. You can enjoy your drive with the following functions. • CD playback You can play CD-DA (also containing CD TEXT) and CD-R/CD-RW (MP3/WMA files). Type of discs Label on the disc CD-DA MP3 WMA Getting Started Preparing the card remote commander Before using the card remote commander for the first time, remove the insulation film. Tip For how to replace the battery, see "Replacing the lithium battery of the card remote commander." Setting the clock The clock uses a 12-hour digital indication. 1 Press and hold the select button. The setup display appears. 2 Press the select button repeatedly until "CLOCK-ADJ" appears. 3 Press The hour indication flashes. 4 Rotate the volume control dial to set the hour and minute. To move the digital indication, press 5 Press the select button. The setup is complete and the clock starts. To display the clock, press Press again to return to the previous display. Detaching the front panel You can detach the front panel of this unit to prevent theft. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The alarm will only sound if the built-in amplifier is used. 1 Press The unit is turned off. 2 Press , then pull it off towards you. Notes • Do not drop or put excessive pressure on the front panel and display window. • Do not subject the front panel to heat/high temperature or moisture. Avoid leaving it in a parked car or on a dashboard/rear tray. Attaching the front panel Engage part  of the front panel with part  of the unit, as illustrated, and push the left side into position until it clicks. A B • Radio reception - You can store up to 6 stations per band (FM1, FM2, FM3, AM1 and AM2). - BTM (Best Tuning Memory): The unit selects strong signal stations and stores them. • Sound adjustment EQ stage2: You can choose any one of 7 preset equalizer curves. • Auxiliary equipment connection An AUX input jack on the front of the unit allows connection of a portable audio device. Note Do not put anything on the inner surface of the front panel. Location of controls and basic operations Main unit 12 3 4 56 78 OFF EQ3 SEEK SCRL DSPL PUSH SELECT SOURCE SEEK MODE BTM ALBUM 1 2 REP 3 SHUF 4 PAUSE 5 6 9 q; qa qs qd This section contains instructions on the location of controls and basic operations.  OFF button To power off; stop the source.  EQ3 (equalizer) button To select an equalizer type (XPLOD, VOCAL, EDGE, CRUISE, SPACE, GRAVITY, CUSTOM or OFF).  Volume control dial/select button To adjust volume (rotate); select setup items (press and rotate).  SOURCE button To power on; change the source (Radio/CD/ AUX).  Disc slot To insert the disc (label side up), playback starts.  Display window  AUX input jack To connect a portable audio device.   (eject) button To eject the disc.  (front panel release) button  DSPL (display)/SCRL (scroll) button To change display items (press); scroll the display item (press and hold). qf qg  SEEK -/+ buttons CD: To skip tracks (press); skip tracks continuously (press, then press again within about 1 second and hold); reverse/fastforward a track (press and hold). Radio: To tune in stations automatically (press); find a station manually (press and hold).  MODE button To select the radio band (FM/AM).  BTM button To start the BTM function (press and hold).  Number buttons CD ALBUM -/+ (during MP3/ WMA playback) To skip albums (press); skip albums continuously (press and hold REP : SHUF : PAUSE To pause playback. To cancel, press again. Radio: To receive stored stations (press); store stations (press and hold).  Receptor for the card remote commander Card remote commander RM-X151 1 4 qh qj qk OFF ATT SOURCE SEL MODE + - DSPL SCRL 1 2 3 4 5 6 + VOL - ql w; qs wa ws wd The following buttons on the card remote commander have also different buttons/ functions from the unit. Remove the insulation film before use. buttons To control CD/radio, the same as on the unit. Setup, sound setting, etc., can be operated by  .  DSPL (display) button To change display items.  VOL (volume) +/- button To adjust volume.  ATT (attenuate) button To attenuate the sound. To cancel, press again.  SEL (select) button To same as the select button on the unit. buttons To control CD, the same as ALBUM -/+) on the unit. Setup, sound setting, etc., can be operated by  .  SCRL (scroll) button To scroll the display item.  Number buttons To receive stored stations (press); store stations (press and hold). Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless on the unit is pressed, or a disc is inserted to activate the unit first. CD Display items Track number/Elapsed playing time, Disc/artist name, Album number*1, Album name, Track name, Text information*2, Clock *1 Album number is displayed only when the album is changed. *2 When playing an MP3, ID3 tag is displayed, and when playing a WMA, WMA tag is displayed. To change display items, press Tip Displayed items will differ, depending on the disc type, recorded format and settings. For details on MP3/ WMA, see "About MP3 files" and "About WMA files." Repeat and shuffle play 1 During playback, press  (REP) or  (SHUF) repeatedly until the desired setting appears. Select TRACK ALBUM* SHUF ALBUM* SHUF DISC To play track repeatedly. album repeatedly. album in random order. disc in random order. * When an MP3/WMA is played. To return to normal play mode, select " OFF" or "SHUF OFF." Radio Storing and receiving stations Caution When tuning in stations while driving, use Best Tuning Memory (BTM) to prevent an accident. Storing automatically - BTM 1 Press repeatedly until "TUNER" appears. To change the band, press repeatedly. You can select from FM1, FM2, FM3, AM1 or AM2. 2 Press and hold until "BTM" flashes. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored. Storing manually 1 While receiving the station that you want to store, press and hold a number button ( to ) until "MEMORY" appears. Note If you try to store another station on the same number button, the previous stored station will be replaced. Receiving the stored stations 1 Select the band, then press a number button ( to ). Tuning automatically 1 Select the band, then press to search for the station. Scanning stops when the unit receives a station. Repeat this procedure until the desired station is received. Tip If you know the frequency of the station you want to listen to, press and hold to locate the approximate frequency, then press repeatedly to fine adjust to the desired frequency (manual tuning). Other functions Changing the sound settings Adjusting the sound characteristics - BAL/FAD/SUB You can adjust the balance, fader, and subwoofer volume. 1 Press the select button repeatedly until "BAL," "FAD" or "SUB" appears. The item changes as follows: LOW*1  MID*1  HI*1  BAL (left-right)  FAD (front-rear)  SUB (subwoofer volume)*2  AUX*3 *1 When EQ3 is activated. *2 When the audio output is set to "SUB." "ATT" is displayed at the lowest setting, and can be adjusted up to 21 steps. *3 When AUX source is activated. 2 Rotate the volume control dial to adjust the selected item. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. Customizing the equalizer curve - EQ3 "CUSTOM" of EQ3 allows you to make your own equalizer settings. 1 Select a source, then press repeatedly to select "CUSTOM." 2 Press the select button repeatedly until "LOW," "MID" or "HI" appears. 3 Rotate the volume control dial to adjust the selected item. The volume level is adjustable in 1 dB steps, from -10 dB to +10 dB. Repeat steps 2 and 3 to adjust the equalizer curve. To restore the factory-set equalizer curve, press and hold the select button before the setting is complete. After 3 seconds, the setting is complete and the display returns to normal play/reception mode. Tip Other equalizer types are also adjustable. Adjusting setup items - SET 1 Press and hold the select button. The setup display appears. 2 Press the select button repeatedly until the desired item appears. 3 Rotate the volume control dial to select the setting (example "ON" or "OFF"). 4 Press and hold the select button. The setup is complete and the display returns to normal play/reception mode. Note Displayed items will differ, depending on the source and setting. The following items can be set: "" indicates the default settings. CLOCK-ADJ (Clock Adjust) BEEP To set "BEEP-ON" () or "BEEP-OFF." AUX-A*1 (AUX Audio) To turn the AUX source display "AUX-A-ON" () or "AUX-A-OFF." A.OFF (Auto Off) To shut off automatically after a desired time when the unit is turned off: "A.OFF-NO" (), "A.OFF-30S (Seconds)," "A.OFF-30M (Minutes)" or "A.OFF-60M (Minutes)." SUB/REAR*1 To switch the audio output. - "SUB-OUT" (): to output to a subwoofer. - "REAR-OUT": to output to a power amplifier. DEMO (Demonstration) To set "DEMO-ON" () or "DEMO-OFF." DIM (Dimmer) To change the brightness of the display. - "DIM-ON": to dim the display. - "DIM-OFF" (): to deactivate the dimmer. M.DSPL (Motion Display) - "M.DSPL-ON" (): to show moving patterns. - "M.DSPL-OFF": to deactivate the Motion Display. A.SCRL (Auto Scroll) To scroll long displayed item automatically when the album/track is changed. - "A.SCRL-ON" (): to scroll. - "A.SCRL-OFF": to not scroll. LOCAL (Local Seek Mode) - "LOCAL-ON": to only tune into stations with stronger signals. - "LOCAL-OFF" (): to tune normal reception. MONO*2 (Monaural Mode) To improve poor FM reception, select monaural reception mode. - "MONO-ON" : to hear stereo broadcast in monaural. - "MONO-OFF" (): to hear stereo broadcast in stereo. LPF*3 (Low Pass Filter) To select the subwoofer cut-off frequency: "LPF OFF" (), "LPF125Hz" or "LPF 78Hz." LOUD (Loudness) To allow you to listen clearly at low volume levels. - "LOUD -ON" : to reinforce bass and treble. - "LOUD -OFF" (): to not reinforce bass and treble. BTM *1 When the unit is turned off. *2 When FM is received. *3 When the audio output is set to "SUB." Using optional equipment Auxiliary audio equipment By connecting an optional portable audio device to the AUX input jack (stereo mini jack) on the unit and then simply selecting the source, you can listen on your car speakers. The volume level is adjustable for any difference between the unit and the portable audio device. Follow the procedure below: Connecting the portable audio device 1 Turn off the portable audio device. 2 Turn down the volume on the unit. 3 Connect to the unit. AUX Connecting cord Adjusting the volume level Be sure to adjust the volume for each connected audio device before playback. 1 Turn down the volume on the unit. 2 Press repeatedly until "FRONT IN" appears. 3 Start playback of the portable audio device at a moderate volume. 4 Set your usual listening volume on the unit. 5 Press the select button repeatedly until "AUX" appears, and rotate the volume control dial to adjust the input level (-8 dB to +18 dB). Additional Information Precautions • If your car has been parked in direct sunlight, allow the unit to cool off before operating it. • Power antenna (aerial) will extend automatically while the unit is operating. Moisture condensation On a rainy day or in a very damp area, moisture condensation may occur inside the lenses and display of the unit. Should this occur, the unit will not operate properly. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. To maintain high sound quality Be careful not to splash juice or other soft drinks onto the unit or discs. Notes on discs • To keep a disc clean, do not touch its surface. Handle the disc by its edge. • Keep your discs in their cases or disc magazines when not in use. • Do not subject discs to heat/high temperature. Avoid leaving them in a parked car or on a dashboard/rear tray. • Do not attach labels, or use discs with sticky ink/residue. Such discs may stop spinning when used, causing a malfunction, or may ruin the disc. • Do not use any discs with labels or stickers attached. The following malfunctions may result from using such discs: - Inability to eject a disc (due to a label or sticker peeling off and jamming the eject mechanism). - Inability to read audio data correctly (e.g., playback skipping, or no playback) due to heat shrinking of a sticker or label causing a disc to warp. • Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this unit. Attempting to do so may damage the unit. Do not use such discs. • You cannot play 8 cm (3 1/4 in) CDs. • Before playing, clean the discs with a commercially available cleaning cloth. Wipe each disc from the center out. Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog discs. Notes on CD-R/CD-RW discs • Some CD-Rs/CD-RWs (depending on the equipment used for its recording or the condition of the disc) may not play on this unit. • You cannot play a CD-R/a CD-RW that is not finalized. • The unit is compatible with the ISO 9660 level 1/ level 2 format, Joliet/Romeo in the expansion format, and Multi Session. • The maximum number of: - folders (albums): 150 (including root and empty folders). - files (tracks) and folders contained in a disc: 300 (if a folder/file names contain many characters, this number may become less than 300). - displayable characters for a folder/file name is 32 (Joliet), or 64 (Romeo). • When the disc is recorded in Multi Session, only the first track of the first session format is recognized and played (any other format is skipped). The priority of the format is CD-DA and MP3/WMA. - When the first track is a CD-DA, only CD-DA of the first session is played. - When the first track is not a CD-DA, the MP3/ WMA session is played. If the disc has no data in any of these formats, "NO MUSIC" is displayed. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do not conform to the CD standard and may not be playable by this product. Note on DualDiscs A DualDisc is a two sided disc product which mates DVD recorded material on one side with digital audio material on the other side. However, since the audio material side does not conform to the Compact Disc (CD) standard, playback on this product is not guaranteed. Playback order of MP3/WMA files MP3/WMA Folder (album) MP3/WMA file (track) About MP3 files • MP3, which stands for MPEG-1 Audio Layer-3, is a music file compression format standard. It compresses audio CD data to approximately 1/10 of its original size. • ID3 tag versions 1.0, 1.1, 2.2, 2.3 and 2.4 apply to MP3 only. ID3 tag is 15/30 characters (1.0 and 1.1), or 63/126 characters (2.2, 2.3 and 2.4). • When naming an MP3 file, be sure to add the file extension ".mp3" to the file name. • During playback or fast-forward/reverse of a VBR (variable bit rate) MP3 file, elapsed playing time may not display accurately. Note If you play a high-bit-rate MP3, such as 320 kbps, sound may be intermittent. About WMA files • WMA, which stands for Windows Media Audio, is a music file compression format standard. It compresses audio CD data to approximately 1/22* of its original size. • WMA tag is 63 characters. • When naming a WMA file, be sure to add the file extension ".wma" to the file name. • During playback or fast-forward/reverse of a VBR (variable bit rate) WMA file, elapsed playing time may not display accurately. * only for 64 kbps Note Playback of the following WMA files is not supported. - lossless compression - copyright-protected If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Maintenance Replacing the lithium battery of the card remote commander Under normal conditions, the battery will last approximately 1 year. (The service life may be shorter, depending on the conditions of use.) When the battery becomes weak, the range of the card remote commander becomes shorter. Replace the battery with a new CR2025 lithium battery. Use of any other battery may present a risk of fire or explosion. + side up 2  1 Notes on the lithium battery • Keep the lithium battery out of the reach of children. Should the battery be swallowed, immediately consult a doctor. • Wipe the battery with a dry cloth to assure a good contact. • Be sure to observe the correct polarity when installing the battery. • Do not hold the battery with metallic tweezers, otherwise a short-circuit may occur. WARNING Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Fuse (10 A) Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, detach the front panel and clean the connectors with a cotton swab. Do not apply too much force. Otherwise, the connectors may be damaged. Main unit Back of the front panel Notes • For safety, turn off the ignition before cleaning the connectors, and remove the key from the ignition switch. • Never touch the connectors directly with your fingers or with any metal device. Removing the unit 1 Remove the protection collar.  Detach the front panel.  Pinch both edges of the protection collar, then pull it out.  2 Remove the unit.  Insert both release keys simultaneously until they click. Hook facing inwards.  Pull the release keys to unseat the unit.  Slide the unit out of the mounting. Specifications AUDIO POWER SPECIFICATIONS CEA2006 Standard Power Output: 16 Watts RMS × 4 at 4 Ohms < 1% THD+N SN Ratio: 82 dBA (reference: 1 Watt into 4 Ohms) CD Player section Signal-to-noise ratio: 120 dB Frequency response: 10 - 20,000 Hz Wow and flutter: Below measurable limit Tuner section FM Tuning range: 87.5 - 107.9 MHz Antenna terminal: External antenna (aerial) connector Intermediate frequency: 10.7 MHz/450 kHz Usable sensitivity: 9 dBf Selectivity: 75 dB at 400 kHz Signal-to-noise ratio: 67 dB (stereo), 69 dB (mono) Harmonic distortion at 1 kHz: 0.5 % (stereo), 0.3 % (mono) Separation: 35 dB at 1 kHz Frequency response: 30 - 15,000 Hz AM Tuning range: 530 - 1,710 kHz Antenna (aerial) terminal: External antenna (aerial) connector Intermediate frequency: 10.7 MHz/450 kHz Sensitivity: 30 µV Power amplifier section Outputs: Speaker outputs (sure seal connectors) Speaker impedance: 4 - 8 ohms Maximum power output: 45 W × 4 (at 4 ohms) General Outputs: Audio outputs terminal (sub/rear switchable) Power antenna relay control terminal Power amplifier control terminal Inputs: Antenna (aerial) input terminal AUX input jack (stereo mini jack) Tone controls: Low: ±10 dB at 60 Hz Mid: ±10 dB at 1 kHz (XPLOD) High: ±10 dB at 10 kHz Power requirements: 12 V DC car battery (negative ground) Dimensions: Approx. 178 × 50 × 179 mm (7 1/8 × 2 × 7 1/8 in) (w/h/d) Mounting dimensions: Approx. 182 × 53 × 162 mm (7 1/4 × 2 1/8 × 6 1/2 in) (w/h/d) Mass: Approx. 1.2 kg (2 lb 11 oz) Supplied accessories: Card remote commander: RM-X151 Parts for installation and connections (1 set) Connecting cord MPEG Layer-3 audio coding technology and patents licensed from Fraunhofer IIS and Thomson. Design and specifications are subject to change without notice. • Halogenated flame retardants are not used in the certain printed wiring boards. • Halogenated flame retardants are not used in cabinets. • Packaging cushions are made from paper. Troubleshooting The following checklist will help you remedy problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General No power is being supplied to the unit. • Check the connection. If everything is in order, check the fuse. • If the unit is turned off and the display disappears, it cannot be operated with the remote commander.  Turn on the unit. The power antenna (aerial) does not extend. The power antenna (aerial) does not have a relay box. No sound. • The volume is too low. • The ATT function is activated. • The position of the fader control "FAD" is not set for a 2-speaker system. No beep sound. • The beep sound is canceled. • An optional power amplifier is connected and you are not using the built-in amplifier. The contents of the memory have been erased. • The power supply lead or battery has been disconnected. • The power supply lead is not connected properly. Stored stations and correct time are erased. The fuse has blown. Makes noise when the position of the ignition key is switched. The leads are not matched correctly with the car's accessory power connector. During playback or reception, demonstration mode starts. If no operation is performed for 5 minutes with "DEMO-ON" set, demonstration mode starts.  Set "DEMO-OFF." The display disappears from/does not appear in the display window. • The dimmer is set "DIM-ON." • The display disappears if you press and hold  Press and hold on the unit until the display appears. • The connectors are dirty. The Auto Off function does not operate. The unit is turned on. The Auto Off function activates after turning off the unit.  Turn off the unit. Card remote commander operation is not possible. Make sure the insulation film has been removed. CD playback The disc cannot be loaded. • Another disc is already loaded. • The disc has been forcibly inserted upside down or in the wrong way. The disc does not playback. • Defective or dirty disc. • The CD-Rs/CD-RWs are not for audio use. MP3/WMA files cannot be played back. The disc is incompatible with the MP3/WMA format and version. MP3/WMA files take longer to play back than others. The following discs take a longer time to start playback. - a disc recorded with a complicated tree structure. - a disc recorded in Multi Session. - a disc to which data can be added. The display items do not scroll. • For discs with very many characters, those may not scroll. • "A.SCRL" is set to "OFF".  Set "A.SCRL-ON."  Press and hold SCRL). The sound skips. • Installation is not correct.  Install the unit at an angle of less than 45° in a sturdy part of the car. • Defective or dirty disc. The disc will not eject. Press  (eject). Radio reception The stations cannot be received. The sound is hampered by noises. • Connect a power antenna (aerial) control lead (blue) or accessory power supply lead (red) to the power supply lead of a car's antenna (aerial) booster (only when your car has built-in FM/AM antenna (aerial) in the rear/side glass). • Check the connection of the car antenna (aerial). • The auto antenna (aerial) will not go up.  Check the connection of the power antenna (aerial) control lead. • Check the frequency. Preset tuning is not possible. • Store the correct frequency in the memory. • The broadcast signal is too weak. Automatic tuning is not possible. • Setting of the local seek mode is not correct.  Tuning stops too frequently: Set "LOCAL-ON."  Tuning does not stop at a station: Set "MONO-ON." • The broadcast signal is too weak.  Perform manual tuning. During FM reception, the "ST" indication flashes. • Tune in the frequency accurately. • The broadcast signal is too weak.  Set "MONO-ON." An FM program broadcast in stereo is heard in monaural. The unit is in monaural reception mode.  Set "MONO-OFF." Error displays/Messages ERROR • The disc is dirty or inserted upside down.  Clean or insert the disc correctly. • A blank disc has been inserted. • The disc cannot play because of some problem.  Insert another disc. FAILURE The connection of speakers/amplifiers is incorrect.  See the installation/connections manual of this model to check the connection. L. SEEK +/- The local seek mode is on during automatic tuning. NO INFO Text information is not written in the MP3/WMA file. NO MUSIC The disc does not contain a music file.  Insert a music CD. NO NAME An album/track name is not written in the track. OFFSET There may be an internal malfunction.  Check the connection. If the error indication remains on in the display, consult your nearest Sony dealer. PUSH EJT The disc cannot be ejected.  Press  (eject). READ The unit is reading all track and album information on the disc.  Wait until reading is complete and playback starts automatically. Depending on the disc structure, it may take more than a minute. " " or " " During reverse or fast-forward, you have reached the beginning or the end of the disc and you cannot go any further. " " The character cannot be displayed with the unit. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began. If you have any questions/problems regarding this product, try the following: 1 Read Troubleshooting in these Operating Instructions. 2 Reset the unit. (Only for models with a RESET button.) Note: Stored data may be erased. 3 Please contact (U.S.A. only); Call 1-800-222-7669 URL http://www.SONY.com