Sony CFD-S200 Operating Instructions - Page 2

Location of controls Inserting a cassette With the side you want to play facing you Loading a CD With the labeled side up u* ., > Z PUSH TUNE -, + OPEN/CLOSE * POWER x MEGA BASS SLEEP VOL +*, - RADIO BAND i AUTO PRESET TAPE CD Remote Control POWER FUNCTION u x BAND .,> PRESET -, + VOL -, +* *The button has a tactile dot. OPR/BATT Display D Total track number Display Number buttons MODE Remote sensor DISPLAY ENT MEMORY Total playing time E Programmed track Playing order To turn on/off the power Press POWER. To adjust the volume Press VOL +, -. To listen through headphones Connect the headphones to the i (headphones) jack. Adjusting the sound emphasis To reinforce the bass sound Press MEGA BASS. "MEGA BASS" appears in the display. To return to normal sound, press the button again. Falling asleep to music 1 Play the music source you want. 2 Press SLEEP to display "SLEEP." 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: "60" t "90" t "120" t "OFF" t "10" t "20" t "30". To cancel the sleep function Press POWER to turn off the power. Note When you are playing a tape using this function: If the tape length of one side is longer than the set time, the player will not go off until the tape reaches the end. Playing a CD 1 Press CD (direct power-on). 2 Load a CD in the CD compartment. 3 Press Z PUSH OPEN/CLOSE to close the CD compartment. 4 Press u. The player plays all the tracks once. To stop playback pause playback go to the next track go back to the previous track remove the CD locate a specific track directly* locate a point while listening to the sound locate a point while observing the display Press x u Press the button again to resume play after pause. > . Z PUSH OPEN/CLOSE a number button of the track. > (forward) or . (backward) while playing until you find the point. > (forward) or . (backward) in pause until you find the point. * You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication by pressing x. Tip To locate a track numbered over 10, press >10 first, then the corresponding number buttons. Example:To play track number 23, press >10 first, then 2 and 3. Using the display To check the total track number and playing time Press DISPLAY•ENT•MEMORY in stop mode (see fig. D). To check the remaining time Press DISPLAY•ENT•MEMORY repeatedly while playing a CD. The display changes as follows: t the current track number and playing time r the current track number and the remaining time on the current track* r the number of tracks left and remaining time on the CD * For a track whose number is more than 20, the remaining time appears as "- -:- -" in the display. Selecting the play mode Press MODE until "REP 1" "REP ALL" "SHUF" "SHUF REP" "PGM" "PGM REP" appears in the display. Then proceed as follows: To repeat a single track repeat all tracks shuffle play repeat tracks in random order Select "REP 1" "REP ALL" "SHUF" "SHUF REP" Then do this Press the number button for the track you want to repeat. Press u. Press u. Press u. program play "PGM" repeat programmed tracks "PGM REP" Press the number buttons for the tracks you want to program in the order you want up to 20 tracks (see fig. E). Then press u. Press the number buttons for the tracks you want to program in the order you want up to 20 tracks. Then Press u. To cancel selected play mode Press MODE until the selected mode disappears from the display. To check the programmed track and playing order in the display To check the order of tracks before play, press DISPLAY•ENT•MEMORY. Every time you press the button, the track number appears in the programmed order. To change the current program Press x once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new program following the programming procedure. Tip You can record your own program. After you've created the program, insert a blank tape and press z to start recording. Listening to the radio 1 Press RADIO BAND•AUTO PRESET until the band you want appears in the display (direct power-on). Each time you press the button, the indication changes as follows: "FM" t "AM". 2 Hold down TUNE + or - until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. Tip If the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play in monaural. Presetting radio stations You can store radio stations into the player's memory. You can preset up to 30 radio stations, 20 for FM and 10 for AM in any order. 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Hold down RADIO BAND•AUTO PRESET for 2 seconds until "AUTO" flashes in the display. 3 Press DISPLAY•ENT•MEMORY. The stations are stored in memory from the lower frequencies to the higher ones. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds. To select the preset number over 10, press >10 first, then the corresponding number buttons. You need to hold down the last number button to enter for about 2 seconds. (Example: To select 12, press >10 and 1 first, then hold down 2 for about 2 seconds.) Playing preset radio stations 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Press the number buttons to tune in the stored station. To tune in a preset station over 10, press >10 first, then corresponding number buttons. (Example: To tune in a preset station 12, press >10 and 1 first, and then press 2.) On the remote 1 Press BAND. 2 Press PRESET + or - to tune in the stored station. Playing a tape 1 Press TAPE (direct power-on). 2 Press xZ to open the tape compartment and insert a recorded tape. Close the compartment. Use TYPE I (normal) tape only. 3 Press n. To stop playback Press xZ fast-forward or rewind the tape m or M pause playback X Press the button again to resume play after pause. eject the cassette xZ Recording 1 Press xZ to open the tape compartment and insert a blank tape. Use TYPE I (normal) tape only. 2 Select the program source you want to record. To record from the CD player Press CD and insert a CD (See "Playing a CD"). To record from the radio Press RADIO BAND•AUTO PRESET and tune in the station you want (See "Listening to the radio"). 3 Press z to start recording. (n is depressed automatically.) To stop recording pause recording Press xZ X Press the button again to resume recording. Tips • Adjusting the volume or the audio emphasis will not affect the recording level. • If the AM program makes a whistling sound after you've pressed z in step 3, press MODE to select the position of ISS (Interference Suppress Switch) that most decreases the noise. • For the best results, use the AC power as a power source for recording. • To erase a recording, proceed as follows: 1 Insert a tape with the recording you want to erase. 2 Press TAPE. 3 Press z.