Sony CFD-S22 Operating Instructions - Page 2

Location of controls TONE (CFD-S32/S32L only) RADIO BAND TAPE Tape compartment CD compartment CD AUTO PRESET OPR/BATT PLAY MODE indicator MONO/ST* Z PUSH OPEN/CLOSE Remote Control (CFD-S32/S32L only) SLEEP FUNCTION OPERATE (or POWER) Number buttons MEGA BASS OPERATE (or POWER) SLEEP TUNING -, + ., > x DISPLAY ENT i (headphones) jack u MEMORY Number buttons for VOLUME +,- CD/RADIO DIRECT OPERATION * The name of this button is PLAY MODE•MONO/ST for CFD-S22/S32, PLAY MODE•MONO/ST ISS for CFD-S22L/S32L/922L. MODE* BAND TUNE +, - X N LOOP FLASH VOL +,- x ., > MEGA BASS TONE * MODE on the remote has the same function as PLAY MODE•MONO/ST on the player. Tip To listen through headphones, connect the headphones to the i (headphones) jack. Adjusting the sound emphasis (MEGA BASS/TONE) Reinforcing the bass sound Press MEGA BASS. "MEGA BASS" appears in the display. To return to normal sound, press the button again. Adjusting the tone (CFD-S32/S32L only) Press TONE. To enhance Display the high tone HI the low tone LO Playing a CD 1 Press CD (direct power-on). 2 Press Z PUSH OPEN/CLOSE down to open the CD compartment and place a CD in the CD compartment. c With the labeled side up 3 Close the CD compartment. c 4 Press u (N on the remote, CFD-S32/S32L only). The player plays all the tracks once. Display Track number Playing time To adjust the volume stop playback pause playback go to the next track go back to the previous track remove the CD turn on/off the player Press VOLUME +, - (VOL +, - on the remote, CFD-S32/S32L only) x u (X on the remote, CFD-S32/S32L only) Press the button again to resume play after pause. > . Z PUSH OPEN/CLOSE OPERATE (or POWER) Using the display Checking the total track number and playing time Press DISPLAY ENT•MEMORY in stop mode. Total track number Total playing time Checking the remaining time Press DISPLAY ENT•MEMORY while playing a CD. To display Press DISPLAY ENT•MEMORY the current track number and the remaining time on the current track* once the number of tracks left and remaining time on the CD twice the current track number and playing time three times * For a track whose number is more than 20, the remaining time appears as "- -:- -" in the display. Locating a specific track To locate a specific track directly a point while listening to the sound a point while observing the display Press a number button of the track. > (forward) or . (backward) while playing until you find the point. > (forward) or . (backward) in pause until you find the point. Tip When you locate a track numbered over 10, press >10 first, then the corresponding number buttons. Example:To play track number 23, press >10 first, then 2 and 3. Note You cannot locate a specific track if "SHUF" or "PGM" is lit in the display. Turn off the indication by pressing x. Repeat Play 1 Press CD. 2 Proceed as follows: To repeat a single track all the tracks tracks in random order programmed tracks Do this 1 Press PLAY MODE•MONO/ST until "REP 1" appears. 2 Press the number button for the track you want to repeat. 1 Press PLAY MODE•MONO/ST until "REP ALL" appears. 2 Press u. 1 Press PLAY MODE•MONO/ST until "SHUF REP" appears. 2 Press u. 1 Press PLAY MODE•MONO/ST until "PGM REP" appears. 2 Press the number buttons for the tracks you want to programme in the order you want up to 20 tracks. 3 Press u. To cancel Repeat Play Press PLAY MODE•MONO/ST until "REP" disappears from the display. Shuffle Play 1 Press CD. 2 Press PLAY MODE•MONO/ST until "SHUF" appears in the display. 3 Press u to start shuffle play. To cancel Shuffle Play Press PLAY MODE•MONO/ST until "SHUF" disappears from the display. Programme Play 1 Press CD. 2 Press PLAY MODE•MONO/ST until "PGM" appears in the display. 3 Press the number buttons for the tracks you want to programme in the order you want. You can arrange the playing order of up to 20 tracks. Display Programmed track 4 Press u to start program play. Playing order To cancel Programme Play Press PLAY MODE•MONO/ST until "PGM" disappears from the display. To check the order of tracks before play Press DISPLAY ENT•MEMORY. Every time you press the button, the track number appears in the programed order. To change the current programme Press x once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new programme following the programming procedure. Tips • You can play the same program again, since the program is saved until you open the CD compartment. • You can record your own program. After you've created the programme, insert a blank tape and press z to start recording. Enjoying Sound effects (LOOP/FLASH) (CFD-S32/S32L only) You can repeat part of a CD (LOOP) and can "flash" the CD sound (FLASH) during playback. 1 Play a CD. 2 Press and hold LOOP or FLASH at the point you want to start the function. To repeat a selected part of a CD "flash" the CD sound Press and Hold LOOP on the remote FLASH on the remote To cancel the LOOP or FLASH function Release the button. The player returns to normal play. Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. • Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. • Do not stick paper or sticker on the CD, nor scratch the surface of the CD. • After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. Listening to the radio 1 Press RADIO BAND•AUTO PRESET until the band you want appears in the display (direct power-on). Each time you press the button, the indication changes as follows: CFD-S22/S32: "FM1" n "FM2" n "AM" CFD-S22L/S32L/922L: "FM1" n "FM2" n "MW" n "LW". Display 2 Hold down TUNING + or - (TUNE + or - on the remote, CFD-S32/S32L only) until the frequency digits begin to change in the display. Display The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. To adjust the volume turn on/off the radio Press VOLUME +, - (VOL +, - on the remote, CFD-S32/S32L only) OPERATE (or POWER) To improve broadcast reception Reorient the antenna for FM. Reorient the player itself for AM or MW/LW. FM AM/MW/LW Tips • The "FM1" and "FM2" bands have the same functions. You can store the stations you want separately in "FM1" and "FM2". • If the FM broadcast is noisy, press PLAY MODE•MONO/ST until "Mono" appears in the display and the radio will play in monaural. Presetting radio stations You can store radio stations into the player's memory. You can preset up to 30 radio stations (CFD-S22/S32) or 40 radio stations (CFD-S22L/S32L/ 922L), 10 for each band in any order. 1 Press RADIO BAND•AUTO PRESET to select the band. Display 2 Hold down RADIO BAND•AUTO PRESET for 2 seconds until "AUTO" flashes in the display. Display 3 Press DISPLAY ENT•MEMORY. The stations are stored in memory from the lower frequencies to the higher ones. Tip If you automatically preset the "FM1" or "FM2" band, 10 radio stations are stored in "FM1" band and 10 more radio stations are stored in "FM2" band. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down the number buttons that you want to preset the new station on for about 2 seconds. Display CD/RADIO DIRECT OPERATION c The new station replaces the old one. Playing preset radio stations 1 Press RADIO BAND•AUTO PRESET to select the band. 2 Press the number buttons to tune in the stored station. CD/RADIO DIRECT OPERATION