Sony CMT-HX7BT Operating Manual - Page 31

Tuner, To change the AM tuning interval, To improve tuner reception

Get Sony CMT-HX7BT - Micro Hi Fi Component System PDF manuals and user guides View all Sony CMT-HX7BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Others Tuner Severe hum or noise, or stations cannot be received. ("TUNED" or "ST" flashes on the display.)  Connect the antenna properly.  Find a location and an orientation that provide good reception, and then set up the antenna again.  Keep the antennas, SiriusConnect Home tuner, and AC adaptor away from the speaker cords and the power cord to avoid picking up noise.  Connect a commercially available external antenna.  Consult your nearest Sony dealer if the supplied AM antenna has come off the plastic stand.  Turn off nearby electrical equipment. The system cannot receive satellite channels at all.  Check that the XM Mini-Tuner and Home Dock or the SiriusConnect Home tuner are connected properly.  The receiving condition is not good. Move the antenna to the place where the condition is good.  Check that you subscribed to the desired satellite radio service (see page 12). To change the AM tuning interval The AM tuning interval is factory-preset to 9 kHz (or 10 kHz, for some areas). Use buttons on the unit to change the AM tuning interval. 1 Tune in any AM station, and then turn off the system. 2 While holding down TUNER/BAND , press All the AM preset stations are erased. To reset the interval to the factory preset, repeat the procedure. To improve tuner reception Turn off CD player power by using the CD power management function. By default, CD power is turned on. 1 Press FUNCTION  repeatedly to select the CD function, and then turn off the system. 2 After "STANDBY" stops flashing, press /  on the unit while holding down /CANCEL  on the unit. "CD POWER OFF" appears. With CD player power turned off, disc access time is increased. To turn on CD player power, repeat the procedure until "CD POWER ON" appears. To reset the system to factory settings If the system still does not operate properly, reset the system to factory settings. Use buttons on the unit to reset the system to its factory default settings. 1 Disconnect and reconnect the power cord, and then turn on the system. 2 Press /CANCEL , DSGX  and /  at the same time. All user-configured settings, such as preset radio stations, SIRIUS Parental Lock password, timer, and the clock, are deleted. 31GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
²1
GB
Others
Tuner
Severe hum or noise, or stations
cannot be received. (“TUNED” or “ST”
flashes on the display.)
Connect the antenna properly.
Find a location and an orientation that
provide good reception, and then set
up the antenna again.
Keep the antennas, SiriusConnect
Home tuner, and AC adaptor away
from the speaker cords and the power
cord to avoid picking up noise.
Connect a commercially available
external antenna.
Consult your nearest Sony dealer if the
supplied AM antenna has come off the
plastic stand.
Turn off nearby electrical equipment.
The system cannot receive satellite
channels at all.
Check that the XM Mini-Tuner and
Home Dock or the SiriusConnect
Home tuner are connected properly.
°e receiving condition is not good.
Move the antenna to the place where
the condition is good.
Check that you subscribed to the
desired satellite radio service (see page
12).
To change the AM tuning interval
°e AM tuning interval is factory-preset
to 9 kHz (or 10 kHz, for some areas).
Use buttons on the unit to change the
AM tuning interval.
1
Tune in any AM station, and then
turn off the system.
2
While holding down TUNER/BAND
, press
/
.
All the AM preset stations are erased.
To reset the interval to the factory
preset, repeat the procedure.
To improve tuner reception
Turn off CD player power by using the
CD power management function. By
default, CD power is turned on.
1
Press FUNCTION
repeatedly to
select the CD function, and then turn
off the system.
2
After “STANDBY” stops flashing, press
/
on the unit while holding
down
/CANCEL
on the unit.
“CD POWER OFF” appears. With CD
player power turned off, disc access
time is increased. To turn on CD
player power, repeat the procedure
until “CD POWER ON” appears.
To reset the system to factory settings
If the system still does not operate
properly, reset the system to factory
settings.
Use buttons on the unit to reset the
system to its factory default settings.
1
Disconnect and reconnect the power
cord, and then turn on the system.
2
Press
/CANCEL
, DSGX
and
/
at the same time.
All user-configured settings, such as
preset radio stations, SIRIUS Parental
Lock password, timer, and the clock,
are deleted.