Sony CPD-220GS Operating Instructions (primary manual) - Page 6

Setup, Selecting, screen, Display, Language

Get Sony CPD-220GS PDF manuals and user guides View all Sony CPD-220GS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

e mg Started Setup Before using this monitor, check that the following items are included in your carton: • Monitor (1) • Power cord (1) • Macintosh adapter (1) • Windows® Monitor Information Disk (1) • Warranty card (1) • These operating instructions (1) • Audio miniplug cord (1) This monitor works with any IBM or compatible system equipped with VGA or greater graphics capability. Although this monitor works with other platforms running at horizontal frequencies between 30 and 85 kHz including Macintosh and Power Macintosh systems, a cable adapter is required. Please consult your dealer for advice on which adapter is suitable for your needs. c...4111.711.; t About the supplied Macintosh adapter The supplied Macintosh adapter is compatible with Macintosh LC, Performa, Quadra and Power Macintosh series computers. Macintosh II series and some older versions of Power Book models may need an adapter with micro switches (not supplied). Note Do not short the pins of the video signal cable. With the monitor switched off, connect one end of the power cord to the monitor and the other end to a power outlet. to a power outlet to AC IN Power cord (supplied) Connecting to an IBM PC/AT, Macintosh or compatible computer With the computer switched off, connect the video signal cable to the computer's video output. BM PC/AT or compatible computer 4 to video output Macintosh or compatible computer 000 t to video output Macintosh adapter (supplied) LI? •1c-; I I fill- The installation of your monitor is complete. Note If "OUT OF SCAN RANGE" or "NO INPUT SIGNAL" appears on the screen, see "Warning Messages" on page 18. For customers using Windows® 95/98 Install the new model information from the "Windows® Monitor Information Disk" into your PC. Selecting the On-screen Display Language If you need to change the OSD language, see "Selecting the on-screen display language" on page 15. The default setting is English. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
e
mg
Started
Setup
Before
using
this
monitor,
check
that
the
following
items
are
included
in
your
carton:
•
Monitor
(1)
•
Power
cord
(1)
•
Macintosh
adapter
(1)
•
Windows®
Monitor
Information
Disk
(1)
•
Warranty
card
(1)
•
These
operating
instructions
(1)
•
Audio
miniplug
cord
(1)
This
monitor
works
with
any
IBM
or
compatible
system
equipped
with
VGA
or
greater
graphics
capability.
Although
this
monitor
works
with
other
platforms
running
at
horizontal
frequencies
between
30
and
85
kHz
including
Macintosh
and
Power
Macintosh
systems,
a
cable
adapter
is
required.
Please
consult
your
dealer
for
advice
on
which
adapter
is
suitable
for
your
needs.
c
.
...4111
.711.;
t
Connecting
to
an
IBM
PC/AT,
Macintosh
or
compatible
computer
With
the
computer
switched
off,
connect
the
video
signal
cable
to
the
computer's
video
output.
BM
PC/AT
or
compatible
computer
4
Macintosh
or
compatible
computer
0 0 0
t
to
video
output
to
video
output
Macintosh
adapter
(supplied)
About
the
supplied
Macintosh
adapter
The
supplied
Macintosh
adapter
is
compatible
with
Macintosh
LC,
Performa,
Quadra
and
Power
Macintosh
series
computers.
Macintosh
II
series
and
some
older
versions
of
Power
Book
models
may
need
an
adapter
with
micro
switches
(not
supplied).
Note
Do
not
short
the
pins
of
the
video
signal
cable.
With
the
monitor
switched
off,
connect
one
end
of
the
power
cord
to
the
monitor
and
the
other
end
to
a
power
outlet.
to
a
power
outlet
to
AC
IN
Power
cord
(supplied)
•1c-;
I
I
fill
-
LI?
The
installation
of
your
monitor
is
complete.
Note
If
"OUT
OF
SCAN
RANGE"
or
"NO
INPUT
SIGNAL"
appears
on
the
screen,
see
"Warning
Messages"
on
page
18.
For
customers
using
Windows®
95/98
Install
the
new
model
information
from
the
"Windows®
Monitor
Information
Disk"
into
your
PC.
Selecting
the
On
-screen
Display
Language
If
you
need
to
change
the
OSD
language,
see
"Selecting
the
on
-screen
display
language"
on
page
15.
The
default
setting
is
English.
6