Sony DRN-XM01H2 Accessory Kit Installation Guide - Page 1
Sony DRN-XM01H2 Manual
View all Sony DRN-XM01H2 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
3-245-381-11(1) Digital Audio Receiver Accessory Kit Installation Guide OWNER'S RECORD The model number is located on the bottom and serial number also on the bottom. Record the serial number in the space provide below. Refer to these numbers whenever you call upon your Sony dealer regarding this product. Model No. Serial No. DRN-XM01C2/DRN-XM01R2/ DRN-XM01H2/ DRN-XM01CK2/ DRN-XM01HK2 Sony Corporation © 2002 Printed in Japan Printed on 100% recycled paper using VOC (Volatile Organic Compound)-free vegetable oil based ink. LIM(IPToErDtaWbleAARuRdAiNo)TY For customers in the USA Please register this product on line at http://www.sony.com/ productregistration. Proper registration will enable us to send you periodic mailings about new products, services, and other important announcements. Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification. Thank you. For DRN-XM01H2/XM01HK2 Customers WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. INFORMATION This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. For All Models Caution • Do not operate the unit in a way that might divert your attention from driving safely. As a driver, you alone are responsible for safely operating your vehicle in accordance with traffic safety laws at all times. • Do not install the unit where it may obstruct your view through the windshield or your view of your vehicle's indicator displays. • Do not install the unit where it may hinder the function of safety devices such as an air-bag. Doing so may prevent the air-bag from functioning properly in the event of an accident. • The installation and use suggestions contained in this manual are subject to any restrictions or limitations that may be imposed by applicable law- purchaser should check applicable law for any restrictions or limitations before installing and/or operating this product. • Failure to follow these safety instructions and warnings may result in a serious accident. Parts for Installation and Connection for DRN-XM01C2 Remote commander (1) Car cradle (1) Car stand (1) Screw (5) Cover (1) Ferrite core (2) Car battery cord (1) Car connecting pack (1) for DRN-XM01R2 Remote commander (1) Car cradle (1) Car stand (1) Screw (5) Cover (1) Ferrite core (6) RF modulator (1) for DRN-XM01CK2 Remote XM antenna (1) commander (1) Car cradle (1) Car stand (1) Screw (5) Cover (1) Ferrite core (2) Water proof cushion (1) Cable guide (3) Cord clamp (4) Cushion with the double-sided adhesive tape (1) Seal (1) Car battery cord (1) Car connecting pack (1) for DRN-XM01H2/XM01HK2 Remote XM antenna (1) Ferrite core (2) commander (1) Home cradle (1) Home stand (1) Audio cord (1) AC power adaptor (1) For DRN-XM01C2/XM01CK2/XM01R2 Installing the Cradle in your Car Install the cradle with the supplied car stand. 1 Choose the mounting position, then shape the base of the stand to match the mounting surface. Note Bend the base gently so there are no gaps between the base and the mounting surface. 2 Clean the mounting surface well. 3 Peel off the protective film from the base of the stand and attach the base to the mounting surface. Make sure the base attaches to the mounting surface completely. Notes • The double-sided tape will not stick firmly if the mounting surface temperature is lower than 20°C (68°F). Use a hairdryer, etc. to warm up the mounting surface before mounting. • Consider the mounting position carefully beforehand. If you change the position after mounting the double-sided tape will weaken. • When removing the stand, preheat the mounting surface with a hairdryer then slowly pull up to remove, or use a commercially available solvent to remove the seal. 4 Fix the stand with the supplied screws. Note Before drilling holes in the mounting surface, make sure there is nothing behind the mounting surface. 5 Remove the knob. 6 Attach the supplied cover over the base of the stand as shown below. 3 2 1 7 Attach the cradle to the stand. To the stand receptacle at the bottom of the cradle 8 Adjust the angle. You can also adjust the angle after installing the main unit into the cradle. Notes • Do not install the unit in a location where it may be subjected to extremely high or low temperatures as the cabinet may become deformed or damaged. After parking your car, the temperature inside the car may raise considerably. Therefore, cover the cradle and the main unit with a white cloth or remove it from the cradle to avoid the direct sunlight. • Do not install the cradle, the main unit and RF modulator in the following places: - Underneath the driver's seat: There may be a danger of the unit getting lodged under the brake pedal. - On the door or ceiling: There may be a danger of the unit falling down or obscuring the driver's view while driving. For All Models Affixing the ferrite cores You must affix the cores (supplied with the model you purchased) in order to comply with Part 15 of the FCC Rules. Wind the cord around the ferrite core once or twice, and then fasten the catch. Make sure that each ferrite core should be attached to the appropriate position as shown in the diagram below. Cord Wind once or twice. Fasten the catch. Affixing the ferrite core to the RF modulator Wind the cord around the RFC-8 ferrite core once, then fasten the catch. Wind the black and red cords around the RFC8 ferrite core twice, then fasten the catch. RFC-8 Approx. 10 mm (13/32 inches) Approx. 10 mm (13/32 inches) POWER ANT DC OUT AUDIO RFC-8 Wind the cord around the RFC-8 ferrite core twice, then fasten the catch. RFC-8 Wind the cord around the RFC-8 ferrite core twice, then fasten the catch. Approx. 5 mm (7/32 inches) RFC-8 RFC-8 Approx. 10 mm (13/32 inches) Affixing the ferrite core to the XM antenna Wind the cord around the RFC8 ferrite core once, then fasten the catch. Approx. 135 mm (5 3/8 inches) Affixing the ferrite core to the AC power adaptor (AC-E60A) Wind the cord around the RFC-8 ferrite core twice, then fasten the catch. Approx. 5 mm (7/32 inches) Affixing the ferrite core to the car battery cord (DCC-E260) Wind the cord around the RFC-8 ferrite core twice, then fasten the catch. Approx. 5 mm (7/32 inches) For DRN-XM01CK2 Installing the XM Antenna to your Car The bottom surface of the XM antenna is made of a magnet. Install the antenna horizontally in a location where the radio wave from the satellite is not interrupted by the body of the car (E.g., roof or trunk lid). Notes on installing the antenna to your car Place the antenna on a flat surface as far away as possible from the edges of the trunk lid or the rear window. • Before mounting the antenna, be sure to attach the supplied seal to the body of the car where the antenna will be mounted, then mount the antenna gently so that it does not damage the body of the car. • Do not leave the cord slackened outside of the car. • Use the cord clamp when fixing the cord, if required. • When removing the antenna, do not pull it by the cord. This may cause the cord to come off the antenna due to the powerful magnet. • The antenna cord is charged with the XM signal and the power supply to the antenna. When wiring the antenna, be careful not to pinch the cord in the moving parts of the car. The damaged cable may cause a malfunction of the antenna and the main unit. • When washing the car in an automatic car wash, remove the antenna. Otherwise, it may damage the body of the car. Installing the antenna to an aluminum or plastic body The antenna cannot be installed on an aluminum or plastic body with the magnet. In this case, use the supplied seal. Painting the antenna The antenna can be painted according to the body color of the car, however, do not use paint that contains metal powder. This may cause deterioration or inability of reception. Do not disassemble the antenna when painting. Placement of the car antenna Place the antenna on a flat and even surface on your car roof. The angle from the ground to the satellite should be about 20 - 60 degrees. If you place the antenna on the trunk lid, make sure your car roof does not block the satellite signal. Depending on where you live, you may be able to receive radio waves that are retransmitted by ground repeaters. Installing the Antenna on the Roof (recommended) Figure of the top Water proof cushion Inside of the trunk Cord clamp** Rubber packing Put the water proof cushion parallel on the rubber packing using the double-sided adhesive tape. Seal XM antenna* Cable guide*** Cable guide*** Figure of the back Water proof cushion Rubber packing Cord clamp** Double-sided adhesive tape Cord clamp** Figure of the side Water proof cushion Rubber packing Double-sided Cord clamp** adhesive tape Put the water proof cushion on the rubber packing with the flat surface downward using the double-sided adhesive tape. * Be sure to install the antenna firmly on a flat surface. Do not install on the corner of the roof. ** • Be sure to install the cord clamp in a lower position where the water proof cushion is mounted. Otherwise, it will cause a water leak into the trunk. • Clean the mounting surface before installing the cord clamp. • Leave the installed cord clamp for 24 hours before installing the cord. Otherwise, the cord clamp may come off due to weak attachment. • To install the cord, insert it into the cord clamp, then press the top of the cord clamp downward so that the cord is securely installed inside the cord clamp. ***• Cut the cable guide, if required. • It is difficult to attach the cable guide to a body or window which has fluorine resin coating. Leading the antenna cord into the car through the space between the door and body When installing the antenna on the roof, you can also lead the antenna cord into the car through the space between door and body. Cord clamp* Antenna cord Cord clamp* Water proof cushion * • Clean the mounting surface before installing the cord clamp. • Leave the installed cord clamp for 24 hours before installing the cord. Otherwise, the cord clamp may come off due to weak attachment. • To install the cord, insert it into the cord clamp, then press the top of the cord clamp downward so that the cord is securely installed inside the cord clamp. Mounting the Antenna with the Supplied Seal and Cushion with the Double-sided Adhesive Tape 2 Attach to the antenna. Cushion with the double-sided 3 adhesive tape Seal 1 Attach to the trunk lid. Note When removing the seal, preheat the mounting surface with a hairdryer then pull up slowly to remove, or use a commercially available solvent to remove the seal. Installing the Antenna on the Trunk Lid 1 Mount the antenna on the trunk lid. Clean the mounting surface before mounting. Seal 20° or less Cable guide 2 Mount the water proof cushion on the right or left side of the trunk lid. To prevent rain water leakage inside the car along the cord, mount the water proof cushion above the rubber packing when the trunk lid is closed. Cable guide* Water proof Seal cushion Trunk lid Rubber packing * • Cut the cable guide, if required. • It is difficult to attach the cable guide to a body or window which has fluorine resin coating.