Sony FW-55BZ30J Wall-Mount Bracket: 3rd Party - Page 6

Attach the Wall-Mount Bracket, Detaching the Table-Top Stand

Page 6 highlights

4 Detaching the Table-Top Stand from the LCD Display. To detach the Table-Top Stand from the LCD Display, remove the screws . Note • Be careful when lifting the LCD Display as the Table- Top Stand is detached, the Table-Top Stand may topple over and cause personal injury. • Take care when removing the Table-Top Stand from the LCD Display to prevent it from falling over and damaging the surface that the LCD Display is sitting on. • Do not remove the Table-Top Stand for any reason other than to install corresponding accessories on the LCD Display. • Be sure the LCD Display is vertical before turning on. To avoid uneven picture uniformity do not power on the LCD Display with the panel facing down. • When attaching the Table-Top Stand again, be sure to fasten the screws (previously removed) to the original holes on the rear of the LCD Display. 2 Attach the Wall-Mount Attachment (supplied with the LCD Display) to the rear of the LCD Display (to make it parallel with the wall). Supplied with the LCD Display VS Wall-Mount Attachment (4) FW-75BU30J / 65BU30J / 55BU30J / 50BU35J / 50BU30J / 43BU35J / 43BU30J / 75BZ30J / 65BZ30J / 55BZ30J / 50BZ35J / 50BZ30J / 43BZ35J / 43BZ30J 1 Remove the screws from the rear of the LCD Display. VS 1.5 N·m {15 kgf·cm} Note • Be sure to fasten the Wall-Mount Attachment when attaching them to the LCD Display. Use only a flat head screwdriver to install the Wall-Mount Attachment. Use of another tool might result in over torqueing the Wall-Mount Attachment and damaging the LCD Display. 3 Attach the Wall-Mount Bracket (not supplied) using the screws (not supplied). Wall-Mount Bracket (not supplied) When using an electric screwdriver, set the torque setting to approximately 1.5 N·m {15 kgf·cm}. Do not lift the Mounting Hook before the screws (two screws each for left/right) are secured. This may distort the Mounting Hook or the LCD Display cabinet. 6 (US) Screw (not supplied) Note • If using an electric screwdriver, set the torque at approximately 1.5 N·m {15 kgf·cm}.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

6
(US)
4
Detaching the Table-Top Stand
from the LCD Display.
To detach the Table-Top Stand from the LCD
Display, remove the screws
.
Note
Be careful when lifting the LCD Display as the Table-
Top Stand is detached, the Table-Top Stand may
topple over and cause personal injury.
Take care when removing the Table-Top Stand from
the LCD Display to prevent it from falling over and
damaging the surface that the LCD Display is sitting
on.
Do not remove the Table-Top Stand for any reason
other than to install corresponding accessories on
the LCD Display.
Be sure the LCD Display is vertical before turning
on. To avoid uneven picture uniformity do not
power on the LCD Display with the panel facing
down.
When attaching the Table-Top Stand again, be sure
to fasten the screws (previously removed) to the
original holes on the rear of the LCD Display.
FW-75BU30J / 65BU30J / 55BU30J / 50BU35J /
50BU30J / 43BU35J / 43BU30J / 75BZ30J /
65BZ30J / 55BZ30J / 50BZ35J / 50BZ30J /
43BZ35J / 43BZ30J
1
Remove the screws from the
rear of the LCD Display.
When using an electric screwdriver, set the torque
setting to approximately 1.5 N·m {15 kgf·cm}.
Do not lift the Mounting Hook before the screws
(two screws each for left/right) are secured. This
may distort the Mounting Hook or the LCD Display
cabinet.
2
Attach the Wall-Mount
Attachment (supplied with the
LCD Display) to the rear of the
LCD Display (to make it parallel
with the wall).
Note
Be sure to fasten the Wall-Mount Attachment when
attaching them to the LCD Display. Use only a flat
head screwdriver to install the Wall-Mount
Attachment. Use of another tool might result in
over torqueing the Wall-Mount Attachment and
damaging the LCD Display.
3
Attach the Wall-Mount Bracket
(not supplied) using the screws
(not supplied).
Note
If using an electric screwdriver, set the torque at
approximately 1.5 N·m {15 kgf·cm}.
VS
VS
Supplied with the
LCD Display
Wall-Mount
Attachment (4)
1.5 N·m
{15 kgf·cm}
Screw (not supplied)
Wall-Mount Bracket
(not supplied)