Sony HDR-PJ30V Handycam® Handbook - Page 15

To remove the battery pack, To use a wall outlet wall socket as a power source

Get Sony HDR-PJ30V PDF manuals and user guides
UPC - 027242820074
View all Sony HDR-PJ30V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Table of Contents Enjoy Useful Functions  The charging times shown in the table above are measured when charging the camcorder at a temperature of 25 C (77 °F). It is recommended that you charge the battery in a temperature range of 10 C to 30 C (50 °F to 86 °F). * The charging times are measured without using the USB Connection support cable.  Tips  When your camcorder is on, you can check the approximate amount of remaining battery power with the remaining battery indicator at the upper right on the LCD screen. To remove the battery pack Close the LCD screen. Slide the BATT (battery) release lever () and remove the battery pack (). To use a wall outlet (wall socket) as a power source Make the same connections as "Step 1: Charging the battery pack" (p. 13). Even if the battery pack is attached, the battery pack is not discharged. Charging the battery pack abroad You can charge the battery pack in any countries/regions using the AC Adaptor supplied with your camcorder within the AC 100 V - 240 V, 50 Hz/60 Hz range.  Notes  Do not use an electronic voltage transformer. Notes on the battery pack  When you remove the battery pack or disconnect the AC Adaptor, turn the camcorder off and make sure that the (Movie)/ (Photo) lamps (p. 24), the access lamp (p. 22) are turned off.  The CHG (charge) lamp or the /CHG (flash/charge) lamp flashes during charging under the following conditions:  The battery pack is not attached correctly.  The battery pack is damaged.  The temperature of the battery pack is low. Remove the battery pack from your camcorder and put it in a warm place.  The temperature of the battery pack is high. Remove the battery pack from your camcorder and put it in a cool place.  We do not recommend using an NP-FV30, which only allows short recording and playback times, with your camcorder.  In the default setting, the power turns off automatically if you leave your camcorder without any operation for about 5 minutes, to save battery power ([A. Shut Off], p. 92). US 15 Index

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
1´
Table of Contents
Enjoy Useful Functions
Index
US
The charging times shown in the table above are measured when charging the camcorder at a
temperature of 25
C (77 °F). It is recommended that you charge the battery in a temperature range of 10
C to 30
C (50 °F to 86 °F).
*
The charging times are measured without using the USB Connection support cable.
Tips
When your camcorder is on, you can check the approximate amount of remaining battery power with the
remaining battery indicator at the upper right on the LCD screen.
To remove the battery pack
Close the LCD screen. Slide the BATT (battery) release lever (
) and remove the battery
pack (
).
To use a wall outlet (wall socket) as a power source
Make the same connections as “Step 1: Charging the battery pack” (p. 13). Even if the battery
pack is attached, the battery pack is not discharged.
Charging the battery pack abroad
You can charge the battery pack in any countries/regions using the AC Adaptor supplied with
your camcorder within the AC 100 V - 240 V, 50 Hz/60 Hz range.
Notes
Do not use an electronic voltage transformer.
Notes on the battery pack
When you remove the battery pack or disconnect the AC Adaptor, turn the camcorder off and make sure
that the
(Movie)/
(Photo) lamps (p. 24), the access lamp (p. 22) are turned off.
The CHG (charge) lamp or the
/CHG (flash/charge) lamp flashes during charging under the following
conditions:
The battery pack is not attached correctly.
The battery pack is damaged.
The temperature of the battery pack is low.
Remove the battery pack from your camcorder and put it in a warm place.
The temperature of the battery pack is high.
Remove the battery pack from your camcorder and put it in a cool place.
We do not recommend using an NP-FV30, which only allows short recording and playback times, with
your camcorder.
In the default setting, the power turns off automatically if you leave your camcorder without any
operation for about 5 minutes, to save battery power ([A. Shut Off], p. 92).