Sony ICD-ST10VTP Operating Instructions (primary manual) - Page 58

Troubleshooting continued, Symptom, Remedy

Get Sony ICD-ST10VTP - Icd Recorder PDF manuals and user guides View all Sony ICD-ST10VTP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Troubleshooting (continued) Symptom Remedy You cannot erase a message. •The message or the folder which contains the message is set to "Read-only" in the computer. Display the message using Windows Explorer and remove the check for "Read-only" under "Properties". You cannot •The remaining memory is too short. The add a recording or an overwritten part will be deleted after the overwrite recording. overwriting part finishes recording. Therefore, you can only overwrite within the remaining recording time. •At a factory setting, REC-OP is set to OFF. Display the menu and set the REC-OP to ON (page 50) . Recording is interrupted. •The advanced VOR function (page 14) is activated. Set the VOR to OFF. Noise is heard. •An object, such as your finger, etc., accidentally rubbed or scratched the unit during recording so that noise was recorded. •The unit was placed near an AC power source, a fluorescent lamp or a mobile phone during recording or playback. •Plug of the connected microphone was dirty when recording. Clean the plug. •The i (headphones) plug is dirty. Clean the plug. Recording level is low. •SENS (microphone sensitivity) is set to L. Display the menu and set SENS to H or M (page 52). Recording level is •This unit is designed to automatically adjust unstable (when the recording level when recording meetings, recording music, etc.). etc., and is not suitable for music recording. Recording is interrupted (when recording from an external device). •If you use a connecting cable without register to connect the sound source to the IC recorder, sound may be recorded interrupted. Make sure to use a registered connecting cable. 58GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
58
GB
Symptom
You cannot erase a
message.
You cannot
add a recording or an
overwrite recording.
Recording is
interrupted.
Noise is heard.
Recording level is
low.
Recording level is
unstable (when
recording music, etc.).
Recording is
interrupted (when
recording from an
external device).
Remedy
•
The message or the folder which contains the
message is set to
“
Read-only
“
in the computer.
Display the message using Windows Explorer
and remove the check for
“
Read-only
“
under
“
Properties
“
.
•
The remaining memory is too short. The
overwritten part will be deleted after the
overwriting part finishes recording. Therefore,
you can only overwrite within the remaining
recording time.
•
At a factory setting, REC-OP is set to OFF.
Display the menu and set the REC-OP to ON
(page 50) .
•
The advanced VOR function (page 14) is
activated.
Set the VOR to OFF.
•
An object, such as your finger, etc., accidentally
rubbed or scratched the unit during recording
so that noise was recorded.
•
The unit was placed near an AC power source,
a fluorescent lamp or a mobile phone during
recording or playback.
•
Plug of the connected microphone was dirty
when recording. Clean the plug.
•
The
i
(headphones) plug is dirty. Clean the
plug.
•
SENS (microphone sensitivity) is set to L.
Display the menu and set SENS to H or M
(page 52).
•
This unit is designed to automatically adjust
the recording level when recording meetings,
etc., and is not suitable for music recording.
•
If you use a connecting cable without register
to connect the sound source to the IC recorder,
sound may be recorded interrupted. Make
sure to use a registered connecting cable.
Troubleshooting (continued)