Sony ICF-C05iP Operating Instructions - Page 2

FM wire antenna AC power adaptor The iPod & iPhone  and VOLUME + buttons have a tactile dot. Setting the clock 1 Plug in the unit. 2 Press and hold CLOCK until the hour flashes in the display. The hour starts to flash in the display. 3 Press ALARM/CLOCK + or - repeatedly to set the hour. 4 Press CLOCK. 5 Repeat steps 3 and 4 to set the minute, and then press CLOCK. The seconds start incrementing from zero. Notes  If you do not press any button for about 1 minute while setting the clock, the clock setting will be canceled.  When pressing any of the rear buttons, hold the unit firmly to prevent slippage. To change the display to the daylight saving time (summer time) indication Change the daylight saving time (summer time) adjustment setting according to the following procedures. Press DST/SUMMER TIME. " " appears in the display and the time indication changes to the daylight saving time (summer time). To deactivate the daylight saving time (summer time) adjustment, press DST/SUMMER TIME again. " " disappears. Setting the brightness of the display Four levels of brightness are available by pres­­sing SNOOZE/BRIGHTNESS. Playing the radio There are two ways to tune. To switch between the two tuning methods (manual tuning or preset), press TUNE MODE/ ENTER MEMORY. Preset tuning You can preset 20 stations for FM. 1 Press FM to turn on the radio. 2 Press and hold FM until "AP" appears in the display. 3 Press TUNE MODE/ENTER MEMORY. The unit automatically presets the available channels in order. If a station cannot be preset automatically You need to preset a station with a weak signal manually. Check that the manual mode is selected. 1 Follow steps 1 and 2 in "Manual tuning" to tune the frequency you wish to preset. 2 Press and hold TUNE MODE/ENTER MEMORY for preset number until the flashes. 3 Press TUNE/PRESET  or  to select the preset number, then press TUNE MODE/ENTER MEMORY. The frequency is stored with the selected preset number. Example: The following display appears when you preset FM 105.7 MHz to preset number 2 for FM. Tuning in to a preset station Check that the preset mode is selected. 1 Press FM to turn on the radio. 2 Press TUNE/PRESET  or  to select the desired preset number. 3 Adjust the volume using VOLUME + or -. Manual tuning Check that the manual mode is selected. 1 Press FM to turn on the radio. 2 Press TUNE/PRESET  or  to tune in to a desired frequency. 3 Adjust the volume using VOLUME + or -. Tuning in to a station The unit automatically scan FM stations. Check that the manual mode is selected. 1 Press FM to turn on the radio. 2 Press and hold TUNE/PRESET  or .  : scans upward through the frequency bands.  : scans downwards through the frequency bands. Scanning starts from the currently-tuned frequency. When a station is received, scanning stops. 3 Adjust the volume using VOLUME + or -. Improving the reception FM: E xtend the FM wire antenna fully to increase reception sensitivity. Notes on radio reception  Keep digital music players or mobile phones away from the FM antenna, as this may lead to reception interference.  When you are listening to the radio with an iPhone connected to the unit, interference with radio reception may occur.  When you are listening to the radio while charging an iPod, interference with radio reception may occur.  Do not place the FM anttena close to the AC power adaptor as noise may result. Playing an iPod You can enjoy iPod audio by connecting to this unit. To use an iPod, refer to the user's guide of your iPod. If you are using an iPhone or iPhone 3G, attach the supplied universal dock adaptor for iPhone or iPhone 3G before inserting into the connector. The adaptor number,  or , is shown on the bottom-rear of the supplied universal dock adaptors.  is for the iPhone, and  is for the iPhone 3G. Check the adaptor number before use. Universal dock adaptor    Notes  When inserting an iPod into the unit, be sure to use the universal dock adaptor supplied with your iPod or commercially available from Apple Inc.  The connector of the unit is exclusively for use with an iPod.  Sony cannot accept responsibility in the event that data recorded on an iPod is lost or damaged when using an iPod connected to this unit.  For details of environmental conditions for operating your iPod, check the website of Apple Inc. 1 Attach the adaptor for your iPod/iPhone. 2 Insert your iPod/iPhone into the connector of the unit. 3 Press iPod & iPhone . The iPod begins to play automatically. You can operate the connected iPod by this unit or the iPod buttons. 4 Adjust the volume using VOLUME + or -. To Turn off the iPod Pause playback Go to the next track Go back to the previous track Locate a point while listening to the sound Locate a point while observing the display Press OFF, or press and hold iPod & iPhone  iPod & iPhone  To resume play, press it again.  *  (forward) or  (backward) while playing and hold it until you find the point.  (forward) or  (backward) in pause and hold it until you find the point. * During playback, this operation goes back to the beginning of the current track. To go back to the previous track, press twice. Notes  When placing or removing the iPod, hold the iPod at the same angle as that of the connector on this unit, and do not twist or bend the iPod as connector damage may result.  Do not carry the unit with an iPod set on the connector. Doing so may cause a malfunction.  When placing or removing the iPod, hold the iPod firmly so as not to topple the unit.  Before disconnecting the iPod, pause playback. To use the unit as a battery charger You can use the unit as a battery charger. Charging begins when the iPod is connected to the unit. Charging status appears in the iPod display. For details, see the user's guide of your iPod. On copyrights  ­i­Pod is a trademark of Apple Inc., registered in the U.S. and other countries.  iPhone is trademark of Apple Inc., registered in the U.S. and other countries.  All other trademarks and registered trademarks are of their respective holders. In this manual, ™ and ® marks are not specified. Setting the alarm This clock radio is equipped with 3 alarm modes-iPod, radio and buzzer. Before setting the alarm, make sure to set the clock (see "Setting the clock"). To set the alarm 1 Press and hold ALARM SET. "WAKE-UP" appears, and the hour flashes in the display. 2 Press ALARM/CLOCK + or - repeatedly until the desired hour appears. To cycle the hour rapidly, press and hold ALARM/CLOCK + or -. 3 Press ALARM ON/OFF. The minute flashes. 4 Repeat step 2 to set the minute. 5 Press ALARM ON/OFF. The alarm mode setting is entered. 6 Press ALARM/CLOCK + or - repeatedly until the desired alarm mode flashes. You can choose one of 3 settings: "iPod", "FM" or "BUZZER." Set the alarm mode as follows: - iPod: see " Setting the iPod alarm." - FM: see " Setting the radio alarm." - BUZZER: see " Setting the buzzer alarm."  Setting the iPod alarm 1 Perform steps 1 to 6 in "To set the alarm." 2 Press ALARM ON/OFF to select "iPod" alarm mode. "VOL" appears in the display. 3 Press ALARM/CLOCK + or - to adjust the volume. 4 Press ALARM ON/OFF. The setting is entered. 5 If "ALARM" does not appear in the display, press ALARM ON/OFF again. The iPod will sound at the set time. When using an iPod touch/iPhone  To wake up to music stored in an iPod touch/ iPhone, connect the iPod touch/iPhone to the unit first, follow the steps above to set alarm time, and then select the music function.  Even if the iPod alarm setting is complete, if you turn the iPod touch/iPhone power off before the unit, the iPod alarm will not work.  Setting the radio alarm 1 Perform steps 1 to 6 in "To set the alarm." 2 Press ALARM ON/OFF to select "FM" alarm mode. "FM", "PRESET" number or "- -" flashes. "- -" is the last station received. 3 Press ALARM/CLOCK + or - to select the desired preset number or "- -". 4 Press ALARM ON/OFF. "VOL" appears in the display. 5 Press ALARM/CLOCK + or - to adjust the volume. 6 Press ALARM ON/OFF. 7 If "ALARM" does not appear in the display, press ALARM ON/OFF again. The radio will turn on at the set time.  Setting the buzzer alarm 1 Perform steps 1 to 6 in "To set the alarm." 2 Press ALARM ON/OFF to select "BUZZER" alarm mode. The setting is entered. 3 If "ALARM" does not appear in the display, press ALARM ON/OFF again. The buzzer will sound at the set time. Note The volume cannot be set for the buzzer alarm. To confirm an alarm time setting Turn off the "ALARM" indicator in the display, and press the ALARM ON/OFF button once. To change an alarm setting Set the alarm again. To doze for a few more minutes Press SNOOZE/BRIGHTNESS. The sound turns off but will automatically come on again after about 10 minutes. You can change the snooze time by pressing SNOOZE/BRIGHTNESS repeatedly within 4 seconds. The maximum length of the snooze time is 60 minutes. To stop the alarm Press ALARM RESET OFF to turn off the alarm. The alarm will sound again at the same time the next day. To deactivate the alarm Press ALARM ON/OFF to turn off the "ALARM" indicator from the display. Note on the alarm in the event of a power interruption In the event of a power interruption, the alarm will work until the battery is totally discharged. However, certain functions will be affected as follows:  The backlight will not light up.  If the alarm mode is set to iPod or radio, it will change to BUZZER automatically.  If a power interruption occurs while the alarm is sounding, the alarm will stop.  If ALARM RESET OFF is not pressed, the alarm will sound for about 5 minutes.  If "" appears in the display, the alarm will not sound in the event of power interruption. Replace the battery if "" appears.  The snooze function will not work.  During a power interruption, the alarm will sound at the set time only once. Setting the sleep timer You can fall asleep to the music, etc., using the built-in sleep timer that turns off the unit automatically after a preset duration. 1 Press SLEEP while the unit is turned on. "SLEEP" appears and the sleep time flashes in the display. 2 Press SLEEP to set the sleep timer duration. Each time you press SLEEP, the duration (in minutes) changes as follows: 90 60 30 15 OFF The display returns to clock mode for about 4 seconds after you have finished the duration setting and released SLEEP, and then the sleep timer starts. The unit will play for the duration you set, and then shut off. To turn off the unit before the preset time Press ALARM RESET OFF. To change the sleep timer setting You can press SLEEP repeatedly to select the desired sleep timer setting even after the sleep timer has been activated. To deactivate the sleep timer Press SLEEP repeatedly to set the sleep timer to "OFF" in step 2. The display shows the frequency for about 10 seconds, and then returns to the current time. To preset another station, repeat these steps. Note If you try to store another station with the same preset number, the previously stored station will be replaced.