Sony ICF-C773 Operating Instructions - Page 2
To Doze for a Few More - am fm clock radio
View all Sony ICF-C773 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
BAND RADIO ON RADIO OFF ALARM RESET NAP P LIGHT SLEE SLEEP LIGHT ON/OFF TUNE/TIME SET ENTER UNE MODE T LIGHT STANDBY BRIGHTNESS ALARM MODE ALARM A ALARM B D.T.S./ CLOCK LIGHT CONTROL HIGH LOW VOLUME * AC power cord NAP FM RADIO SLEEP AM PM STANDBY LIGHT SLEEP MHzkHz RADIO A SOUND WAKE UP PRESET RADIO B SOUND *There is a tactile dot beside VOLUME to show the direction to turn up the volume. Setting the Clock 1 Plug in the clock radio. "AM 12:00" flashes on the display. 2 Hold down D.S.T./CLOCK for a few seconds until a beep sounds. The hour starts to flash on the display. 3 Press TUNE/TIME SET + or - until the correct hour appears. To set the current time rapidly, hold down TUNE/ TIME SET+ or -. 4 Press ENTER/TUNE MODE once. 5 Repeat steps 3 and 4 to set the minute. Two short beeps sound, and the counting of the seconds starts. If you quit during the clock setting, after about 65 seconds the previous display will return. To set the current time from zero seconds, press ENTER/TUNE MODE with the time signal in step 5. To change the display to the daylight saving time (summer time) indication Press D.S.T./CLOCK. " " is displayed and the time indication changes to summer time. To deactivate the summer time function, press D.S.T./CLOCK again. Setting the Brightness of the Backlight Press BRIGHTNESS to select high, middle or low for the display according to your preferences. Changing AM Channel Step The AM channel step differs depending on areas. The channel step of this unit is factory-set to 9 kHz or 10 kHz. Change the settings as shown below to be able to listen to the radio. Area North and South America Other countries/regions Channel step 10 kHz 9 kHz 1 Hold down RADIO OFF/ALARM RESET to turn off the power. 2 While holding down SNOOZE/SLEEP OFF, keep pressing ALARM MODE for more than 5 seconds. Two short beeps sound, and the AM channel step will be changed. If you proceed to step 2 again, the channel step changes again. Notes • When the AM channel step is changed, the preset stations will be initialized. • When the AM channel step is changed, the FM channel step is also changed. Playing the Radio -Manual Tuning 1 Press RADIO ON•BAND to turn on the radio. The display shows the band and frequency for 10 seconds and then changes back to the current time. 2 Press RADIO ON•BAND to select the band. Each press changes the band as follows: AM FM 3 Press ENTER/TUNE MODE so that "PRESET" goes off. 4 Press TUNE/TIME SET+ or - to tune into the desired station. The FM channel step is set to 0.1 MHz and the AM channel step is set to 10 kHz (North and South American model). The FM channel step is set to 0.05 MHz*, the AM channel step is set to 9 kHz (Other models). * The FM frequency display is raised or lowered by a step of 0.1 MHz. For example, frequency 88.00 and 88.05 MHz is displayed as "88.0 MHz." Two short beeps sound when the minimum frequency of each band is received during tuning. 5 Adjust volume using VOLUME. To turn off the radio, press RADIO OFF/ALARM RESET. To check the station being received Press TUNE/TIME SET+ or - lightly. The display shows the band and frequency for 10 seconds and then returns to the previous display. Improving the Reception FM: The AC power cord functions as an FM antenna. Extend the AC power cord fully to increase reception sensitivity. AM: Rotate the unit horizontally for optimum reception. A ferrite bar is built into the unit. Do not operate the unit over a steel desk or metal surface, as this may lead to interference of reception. Presetting Your Favorite Station -Preset Tuning You can preset up to 10 stations in FM, and 5 stations in AM. Presetting a Station 1 Follow steps 1 to 4 in "Piaying the Radio" and manually tune in to the station you wish to preset. 2 Hold down ENTER/TUNE MODE until "PRESET 1" appears and flashes. 3 Press TUNE/TIME SET+ or - to select the number you wish to preset, then press ENTER/TUNE MODE. Example: Display window when you preset FM 90.0 MHz in preset number 2. To preset another station, repeat these steps. To cancel the presetting mode, press RADIO OFF/ALARM RESET. Notes • If you do not press TUNE/TINE SET+ or -, or ENTER/TUNE MODE within 65 seconds, the preset tuning mode will be canceled. • To change the preset station, follow steps 2 and 3. The new station will replace the previous station. Tuning into a Preset Station 1 Press RADIO ON•BAND to turn on the radio. 2 Press RADIO ON•BAND to select the band. 3 Press ENTER/TUNE MODE to display "PRESET". 4 Press TUNE/TIME SET+ or - to tune in to the desired preset station. 5 Adjust the volume using VOLUME. After 10 seconds, the display will return to the current time but the preset number will remain. Tip Press TUNE/TIME SET+ or - repeatedly until the desired mode is selected. Each time of PRESET changes as follows. Example: AM PRESET 1 2 3 4 5 Two short beeps sound when the display returns to "PRESET 1". Setting the Light You can change the setting of the light on the side exterior. The operates as follows: LIGHT ON/OFF: Each time you press LIGHT ON/OFF, the light turns on or off. LIGHT STANDBY: The light turns on when the radio is turned on. The light flashes when ALARM A or B, or NAP timer sound comes on. The light goes out when the radio, the sound alarm or the NAP timer sound is turned off. Press LIGHT ON/OFF to turn on or off the light during the LIGHT STANDBY mode. To turn off LIGHT STANDBY mode, press LIGHT STANDBY again. LIGHT SLEEP: You can enjoy falling asleep to the light using the built-in sleep timer that turns off the light automatically after a preset duration. Press LIGHT SLEEP. The light turns on. You can set the sleep timer to durations of 90, 60, 30, or 15 minutes. Each press changes the display as follows: OFF 90 60 15 30 Two short beeps sound when the display returns to "90". "LIGHT SLEEP" will appear in the display when the duration time is set. The light will turn on for the time you set, then shut off. To turn off the light before the preset time, press LIGHT ON/OFF. LIGHT CONTROL: Changing the Brightness of the light. Turn the variable LIGHT CONTROL to adjust the brightness of the light. Setting the Alarm You can set two types of alarms, radio and sound. The alarm will come on at the same time everyday. Before setting the alarm, make sure to set the clock. (See "Setting the Clock".) Notes • The factory setting alarm time for radio and sound is "PM 12:00". • If you quit during the alarm setting, after about 65 seconds the previous display will return. To Set the Radio Alarm 1 Hold down ALARM A (ALARM B) for a few seconds until a beep sounds. "A (B)" and the hour flash on the display. 2 Press TUNE/TIME SET+ or - to set the desired hour. 3 Press ENTER/TUNE MODE. 4 Repeat steps 2 and 3 to set the minute. 5 Repeat steps 2 and 3 to select the Radio Alarm "RADIO A (RADIO B)" A beep sounds to confirm the setting of time. " " appears and the preset number flashes on the display. 6 Press TUNE/TIME SET+ or - to select the station you last listened or a preset station as "wake up station". Each press of + changes "wake up station" as follows: PRESET (last station) AM PRESET 1 to 5 FM PRESET 1 to 10 Pressing - changes "wake up station" in reverse order. 7 Press ENTER/TUNE MODE again. Two beeps sound to confirm the setting. To use the Radio ALARM, set the alarm mode. (See "Setting the Alarm Mode".) When the alarm comes on at the preset time, RADIO A (RADIO B) flashes on the display and "wake up station" (the station selected in step 5) comes on. The radio is turned off automatically after about 60 minutes. To check the alarm setting Press ALARM A (ALARM B) once. The display shows the preset time. If you press ALARM A (ALARM B) again, the display shows "wake up station". After 4 seconds, the display will return to the current time. To Set the Sound Alarm 1 Follow steps 1 to 5 in "To set the Radio Alarm". 2 Press TUNE/TIME SET+ or - to select the Sound Alarm "A SOUND (B SOUND)". 3 Press ENTER/TUNE MODE. 4 Press TUNE/TIME SET+ or - to select the sound number of beep (1) or melodies (2 to 5). 1: Buzzer 2: Green sleeves 3: "For Eliza" Ludwing van Beethoven 4: "Peer Gynt Suite: Morning" Edvard Hagerup Grieg 5: "Four Seasons: Spring" Antonio Lucio Vivaldi When selecting the number, you can hear the sound of the number. 5 Press ENTER/TUNE MODE again. Two beeps sound to confirm the setting. To use the Sound Alarm, set the alarm mode. (See "Setting the Alarm Mode".) When the alarm comes on at the preset time, "A SOUND (B SOUND)" and the selected sound number flash on the display. The sound is turned off automatically after about 60 minutes. To check the alarm setting Press ALARM A (ALARMB) once. The display shows the preset time . If you press ALARM A (ALARMB)again, the display show the selected sound number. After 4 seconds, the display will return to the current time Setting the Alarm Mode Before setting the alarm mode, be sure to set the alarm time. (See "Setting the Alarm".) Press ALARM MODE repeatedly until the desired mode is selected. Each press of ALARM MODE changes the indication on the display as follows: No alarm Indication A B AB If the same alarm time is set for both ALARM A and B, the ALARM A takes priority. To Doze for a Few More Minutes Press SNOOZE/SLEEP OFF. The radio or sound turns off but will automatically come on again after about 10 minutes. Each time you press SNOOZE/SLEEP OFF, the snooze time changes as follows: 10 20 30 40 50 60 The maximum length of the snooze time is 60 minutes. The display shows the snooze time for a few seconds and returns to show the current time. When you press SNOOZE/SLEEP OFF after the current time appeared, the snooze time starts from 10 minutes again. To Stop the Alarm Press RADIO OFF/ALARM RESET to turn off the alarm. The alarm will come on again at the same time the next day. To Deactivate the Alarm Press ALARM MODE repeatedly so that "A" and "B" go off. Using the NAP Timer (Count Down Timer) The NAP timer sounds the buzzer after a preset time duration. Press NAP repeatedly until the desired minutes are displayed. Each press changes the display as follows: OFF 10 20 30 120 90 60 Two short beeps sound when the display returns to "10". " " and the NAP time are displayed for a few seconds. NAP timer starts counting down the NAP time. When selected NAP time has passed, the buzzer comes on, and " " on the display flash. The buzzer is turned off automatically after about 60 minutes. To Stop NAP Timer Press NAP or RADIO OFF/ALARM RESET to turn off the buzzer. To Deactive NAP Timer Press NAP. " " goes off in the display. Setting the Sleep Timer (Radio Sleep Timer) You can enjoy falling asleep to the radio using the built-in sleep timer that turns off the radio automatically after a preset duration. Press SLEEP. The radio turns on. You can set the sleep timer to durations of 90, 60, 30, or 15 minutes. Each press changes the display as follows: OFF 90 60 15 30 Two short beeps sound when the display returns to "90". " " will appear in the display when the duration time is set. The radio will play for the time you set, then shut off. To turn off the radio before the preset time Press SNOOZE/SLEEP OFF or RADIO OFF/ ALARM RESET. To Use Both Sleep Timer and Alarm You can fall asleep to the radio and also be awakened by the radio or sound alarm at the preset time. 1 Set the alarm. (See "Setting the Alarm".) 2 Set the sleep timer. (See "Setting the Sleep Timer".)