Sony ICF-M88B Operating Instructions - Page 2
Changing AM Channel Step - manual
UPC - 027242636286
View all Sony ICF-M88B manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
RADIO POWER LIGHT ENTER/SELECT TUNE MODE BAND/SET FREEZE PRESET FM MHz kHz AM MPH km/h inch AM mm MPH PM km/h mile CLOCK ODO DIST RT AVG MAX RADIO POWER LIGHT ENTER/SELECT TUNE MODE BAND/SET VOL Jog lever RADIO POWER LIGHT ENTER/SELECT TUNE MODE BAND/SET VOL FM SENS DX/LOCAL FM antenna VOL* * There is a tactile dot beside VOL to show the direction to turn up the volume. For the initial setting (with the radio off) The cycle-computer needs initial set up before using. If the wheel size you set into the cycle-computer is not suitable for using actual wheel size, it is not possible to measure speed and distance correctly. 1 Press and hold BAND/SET for a few seconds to select "mile" or "km". "mile" flashes in the display. Each press of the ENTER/SELECT toggles between "mile" and "km". The unit of speed is "MPH" for miles, and "km/h" for kilometers. Select and show the desirred unit. 2 Press BAND/SET to set a wheel size. The wheel size flashes. Press ENTER/SELECT repeatedly to select your wheel size (inches). Each press changes the display as follows. 26 27 28 12 14 24 22 20 18 16 Note The "mm" values shown on the display are approximate. Adjust the accurate size of the wheel using Jog lever + or - after measuring diameter of your wheel. It is recommend to set the wheel size in "mm" because the cycle-computer calculates in "mm". If you set the wheel size in "mm", the range is from 300 to 750 mm. Push and hold Jog lever to change the value rapidly. 3 Press BAND/SET. "ODO" appears in the display, and the last digit of the total distance (odometer) flashes. If you do not change the odometer, jump to step 4. To change the total distance You can change the default setting of the total distance (odometer) using Jog lever + or - (to increase or decrease) and ENTER/SELECT (to select another digit). 4 Press BAND/SET again. The initial setting is completed. Tips • When you choose the "mile", the range is from 0.0 to 99 999.9 miles. • When you choose the "km", the range is from 0.0 to 159 999.9 kilometers. And the maximum digit range is from 0 to 15. Notes • If you do not make any selections, for within about 65 seconds, or do press TUNE/MODE button during the initial setting mode, the setting mode will be canceled and the unit returns to the previous mode. • If you press the LIGHT button for within about 65 seconds during the initial setting mode, the setting mode will be extended. • If you cancel during initial setting mode, the value of the unit, wheel size and total distance entered will be erased. The unit will revert to the previous setting. • The cycle-computer will not activate during the initial setting mode. • If you press RADIO POWER to turn on the unit during the initial setting mode, the mode is canceled and the radio will activate. • If you change the unit in the initial setting mode, the values showed in the total distance (odometer) setting mode will be automatically converted into the new setting unit. However, when you convert the unit from miles to kilometers, any value over 159 999.9km is shown as 159 999.9km. Displaying data While cycling, current speed is always displayed and updated every second. The highest speed that can be displayed is 124.2 MPH (199.9 km/h) and remains displayed beyond that speed. Below 2.5 MPH (4.0 km/h), 0.0 is displayed. Displaying the odometer Press MODE/FREEZE repeatedly until "ODO" appears. The current total distance is displayed. Note If 99 999.9 miles (160 934.3 km) is exceeded, the odometer returns to zero. Displaying trip distance Press MODE/FREEZE repeatedly until "DIST" appears. At the point you want to start calculating the distance, perform the zero reset operation. For details on how to perform the zero reset operation, refer to "Performing the zero reset." Note If 9 999.9 miles (16 093.3 km) is exceeded, the trip distance returns to zero. Displaying riding time Press MODE/FREEZE repeatedly until "RT" appears. The "Hour: Minute: Second" is indicated in the display. At the point you want to start calculating riding time, perform the zero reset operation. For details on how to perform the zero reset operation, refer to "Performing the zero reset." Riding time is updated every second. When one wheel revolution takes over a second, riding time is updated when the magnet passes the sensor. If the interval at which the magnet passes the sensor is more than 1 minute, the calculation is canceled. Note If the displayed "99:59:59" is exceeded, riding time returns to zero. Displaying average speed Press MODE/FREEZE repeatedly until "AVG" appears. Average speed is calculated according to trip distance and riding time. Displaying maximum speed Press MODE/FREEZE repeatedly until "MAX" appears. The maximum speed recorded to date is displayed. Note If either trip distance or riding time returns to zero, trip distance, riding time and average speed simultaneously return to zero. Performing the zero reset The zero reset operation of trip distance, riding time and average speed are performed simultaneously and cannot reset individually. 1 Press MODE/FREEZE to display either "DIST," "RT" or "AVG." 2 Press and hold RESET for a few seconds. "DIST," "RT" and "AVG" flash. 3 Press RESET again. The zero reset operation is completed, and "DIST," "RT" and "AVG" are set to zero. You can reset maximum speed only. Select "MAX" in step 1, followed by step 2 and 3. Setting Freeze mode You can deactivate odometer calculation, trip distance, riding time, average time, and maximum speed (except for current speed) with the Freeze mode. 1 Press and hold MODE/FREEZE for a few seconds. "FREEZE" lights up, and the cycle-computer enters Freeze mode. To cancel Freeze mode, press and hold MODE/FREEZE for a few seconds. ("FREEZE" is no longer displayed.) Standby mode When your bicycle is stopped with the radio off, and no button is pressed for more than 10 minutes, the cycle-computer enters Standby mode, and only the current time is displayed. To cancel Standby mode When the unit is attached to the Mount At the point where you start and the magnet passes the sensor, or you press any active button, Standby mode is canceled. (The display returns to the previous one before entering Standby mode.) When the unit is not attached to the Mount When you attach the unit to the Mount or press any active button, Standby mode is canceled. Note If the cycle-computer enters Standby mode with Freeze mode activated, Freeze mode is not canceled. Using the Backlight Press LIGHT. The backlight will light for 10 seconds. If any buttons are pressed while the backlight is on, the backlight will turn off 10 seconds after pressing the button. Setting the Clock The clock time display of this unit is a 12-hour system. When the batteries are first installed, "AM 12:00" flashes and "CLOCK" turns on in the display. 1 Press RADIO POWER to turn off the power. 2 Press MODE/FREEZE repeatedly until "CLOCK" appears. 3 Hold down ENTER/SELECT for more than 2 seconds until "AM 12" starts flashing. 4 Push the Jog lever towards + or - to adjust the hour, then press ENTER/SELECT. The beep sounds and the minute setting starts to flash. If you hold down the Jog lever towards + or -, the digit changes rapidly. Midnight is indicated as "AM 12:00" and Noon is indicated by "PM 12:00." g 5 Repeat step 4 above to adjust the minutes. ":" starts flashing and the clock starts operating. To set the current time exactly to the second, adjust the minute setting and then press ENTER/SELECT to synchronize it with a time signal (such as the telephone time signal). Note If you do not push the Jog lever towards + or -, or ENTER/SELECT within about 65 seconds, the clock setting mode will be canceled. Changing AM Channel Step The AM channel step differs depending on area. The channel step of this unit is factory-set to 10 kHz. Change the settings as shown below to be able to listen to the radio. Area North and South American countries Other countries/regions Channel step 10 kHz 9 kHz Note When the AM channel step is changed, only the preset stations on the AM band will be initialized. 1 Press RADIO POWER to turn off the power. 2 While holding down ENTER/SELECT, keep pressing RADIO POWER for more than 5 seconds. Two short beeps sound, and the AM channel step will change and "9" kHz (or "10" kHz) will light up for about 2 seconds in the display. If you proceed to step 2 again, the channel step changes again. Playing the Radio - Manual Tuning 1 Press RADIO POWER to turn on the power. 2 If "PRESET" is displayed, press TUNE MODE so that "PRESET" disappears. Pressing TUNE MODE will switch over between manual tuning mode and preset tuning mode. 3 Press BAND/SET to select the band. Each press changes the band. 4 Push the Jog lever towards + or - to select the desired frequency. If you hold down the Jog lever towards + or -, the frequency changes rapidly. When the frequency matches the broadcast frequency, the broadcast will be received. 5 Adjust the volume using VOL. To turn off the radio, press RADIO POWER. Improving Radio Reception FM: Set FM SENS to LOCAL if interference is prevalent when radio wave intensity is dramatically stronger. Under normal conditions, set to DX. FM SELNOSCDAXL Presetting your Favorite Stations - Preset Tuning You can preset up to 5 AM stations, and 10 FM stations. You can also delete a preset station, whether factory-set or preset yourself. Presetting a Station 1 Follow steps 1 to 5 in "Playing the Radio" and manually tune in to the station you wish to preset. 2 Hold down ENTER/SELECT until the preset number flashes. A preset number with no station will flash. When all preset numbers have assigned stations (factory-set), "1" flashes and "PRESET" appears. 3 Push the Jog lever towards + or - to select the number you wish to preset, then press ENTER/SELECT. If a preset number you select with the Jog lever has an assigned preset station, "PRESET" appears; if no station is assigned, only the number flashes. When you press ENTER/SELECT, the selected preset number lights up in the display. Example: Preset number 2, FM 90.0 MHz To preset another station, repeat the above steps. To change a preset station, preset a new station. The previous station will be canceled. Note If you do not perform a preset operation for about 65 seconds, presetting mode will be canceled. Tuning in to a Preset Station 1 Press RADIO POWER to turn on the power. 2 Press BAND/SET to select the band. 3 Press TUNE/MODE so that "PRESET" and preset number appear. 4 Push the Jog lever towards + or - to select the desired preset number. 5 Adjust the volume using VOL. To turn off the radio, press RADIO POWER. Note If you hold down TUNE/MODE for more than 2 seconds, the unit enters the preset station deleting mode. Press TUNE/MODE again to return to the previous mode. Deleting a Preset Station 1 Follow steps 1 and 3 in "Tuning in to a Preset Station". 2 Push the Jog lever towards + or - to select the preset number to be deleted. 3 Hold down TUNE/MODE for more than 2 seconds until "PRESET", " " and the preset number flash. preset number to be deleted 4 While the letters and the preset number are flashing, press ENTER/SELECT. The station set to the preset number just before the deleted station will be displayed. To delete other stations, repeat steps 2 to 4. If all the preset stations are deleted, "PRESET -" appears in the display. To cancel deleting, press TUNE/MODE while "PRESET", " preset number are flashing. " and the Playing the Radio on the Mount When the current speed is displayed (for example, after having installed the unit on the Mount), pressing a button or the Jog lever (to perform a radio operation) only displays the station frequency and/or current preset number. From this display, press the BAND/SET, TUNE/MODE or Jog lever + or - to perform the desired radio operation. Holding down Jog lever + or -, ENTER/SELECT or TUNE/MODE while the current speed is displayed Jog lever + or - : Pushing the Jog lever displays the current frequency. Pushing and holding the Jog lever changes the frequency or preset number. ENTER/SELECT : Pressing this button displays the current frequency. Pressing and holding selects the Station-presetting mode. TUNE/MODE : Pressing this button displays the current frequency. Pressing and holding selects preset station deleting mode in preset tuning mode. In manual tuning mode, holding down has no effect. Notes • If you perform a radio operation once in the current speed display and do not operate the radio again within 5 seconds, the display automatically returns to the current speed indication. • When the radio is turned off, the current speed display appears. When the radio is turned on, the current frequency is displayed. If you do not perform any operation within 5 seconds, the display returns to the current speed. • While presetting mode or deleting mode, the current speed display will not appear. After completing or canceling the presetting/deleting mode, the current speed display appears after 5 seconds.