Sony KDL-40Z4100/S Quick Setup Guide - Page 2

HD Basic Connection with A/V Receiver Rear of TV VIDEO IN 1 3 S VIDEO COMPONENT IN PC IN 1 2 Y RGB PB IN DIGITAL 1 OUT (OPTICAL) 3 VIDEO L (MONO) AUDIO R PR L AUDIO R AUDIO (1080p/1080i/720p/480p/480i) 4 AUDIO OUT R AUDIO L L AUDIO R (VAR/FIX) Blu-ray Disc/DVD CABLE / ANTENNA A/V Receiver SAT (dish) HD Cable Box or HD Satellite Receiver Splitter Cable/Antenna HD BRAVIA Sync Basic Connection *Rear of TV VIDEO IN 1 3 S VIDEO COMPONENT IN PC IN 1 2 Y RGB PB IN DIGITAL 1 OUT (OPTICAL) 3 VIDEO L (MONO) AUDIO R PR L AUDIO R AUDIO (1080p/1080i/720p/480p/480i) 4 AUDIO OUT R AUDIO L L AUDIO R (VAR/FIX) CABLE / ANTENNA AM SAT IN DVD IN VIDEO 2/BD IN OUT DIGITAL L L HDMI ANTENNA OPT IN OPT IN COAX IN SAT VIDEO 1 DVD R R AUDIO IN AUDIO IN AUDIO IN SA-CD/CD TV VIDEO 1 DMPORT SPEAKERS *A/V Receiver FRONT R FRONT L SUR R SUR L CENTER SUBWOOFER *Blu-ray Disc AC IN HDMI OUT VIDEO OUT VIDEO COMPONENT VIDEO OUT Y PB/CB DIGITAL OUT PCM/DTS/DOLBY DIGITAL COAXIAL OPTICAL S VIDEO PR/CR AUDIO OUT L 5.1CH OUTPUT FRONT REAR CENTER L R R WOOFER SAT (dish) HD Cable Box or HD Satellite Receiver * Signifies a BRAVIA Sync capable device. Splitter Cable/Antenna HD Basic Connection with Home Theater System Rear of TV VIDEO IN 1 3 S VIDEO COMPONENT IN PC IN 1 2 Y RGB PB IN DIGITAL 1 OUT (OPTICAL) 3 VIDEO L (MONO) AUDIO R PR L AUDIO R AUDIO (1080p/1080i/720p/480p/480i) 4 AUDIO OUT R AUDIO L L AUDIO R (VAR/FIX) CABLE / ANTENNA Blu-ray Disc/DVD Cable/SAT (dish) SD Cable Box or SD Satellite Receiver or HD Antenna Home Theater System Coaxial HDMI HD15 Required Cable Types for Connection DVI-to-HDMI Composite Component Audio (L/R) Mini-Pin Audio Audio (L/R) with Mini-Pin Digital Optical Audio DVI - to - HDMI adapter Notes on Connection: ■ Your TV is equipped with four HDMI inputs and two component inputs. Connect your incoming signal source (HD Cable Box, HD Satellite Receiver, or DVD) with HDMI or component video for the best possible picture quality. ■ If your connecting equipment has DVI output instead of the HDMI output, you must use a DVI-to-HDMI cable for the video and also connect an audio cable for the sound. If this is the case, connect the cable to HDMI IN 4 (input) of your TV. ■ When using a DVI-to-HDMI cable, make sure to connect the DVI side first. ■ P&P/PIP functions require Cable/Antenna connection. ■ When receiving a High-Definition signal by an over-the-air antenna, it is best to use an HD antenna. Basic Connection with SD VCR/DVD Rear of TV VIDEO IN 1 3 S VIDEO COMPONENT IN PC IN 1 2 Y RGB PB IN DIGITAL 1 OUT (OPTICAL) 3 VIDEO L (MONO) AUDIO R PR L AUDIO R AUDIO (1080p/1080i/720p/480p/480i) 4 AUDIO OUT R AUDIO L L AUDIO R (VAR/FIX) CABLE / ANTENNA VCR DVD VCR/DVD Combo Splitter Cable/Antenna PC Connection Notebook PC Rear of TV VIDEO IN 1 3 S VIDEO COMPONENT IN PC IN 1 2 Y RGB PB IN DIGITAL 1 OUT (OPTICAL) 3 VIDEO L (MONO) AUDIO R PR L AUDIO R AUDIO (1080p/1080i/720p/480p/480i) 4 AUDIO OUT R AUDIO L L AUDIO R (VAR/FIX) CABLE / ANTENNA SAT HD Cable Box or PC (dish) HD Satellite Receiver Splitter Cable/Antenna Programming the Remote Control Your remote control can be programmed to use other equipment and is pre-programmed to operate the following Sony equipment. Function Button Sony Equipment Code Number DVD DVD Player 31033 AMP Receiver 52172 DISPLAY LIGHT POWER TV POWER STB Digital Satellite 01639 DVD AMP STB TV FUNCTION PREV REPLAY ADVANCE NEXT 2 Programming Other Equipment Follow the steps below to program your TV remote control. PLAY SYNC MENU PAUSE STOP THEATER SOUND PICTURE WIDE CC FREEZE 1 Look for the code in the Manufacturer's Codes List (see Operating Instructions Manual) that corresponds to the equipment you would like to operate with the Sony remote control. If more than one code is provided, try programming the first code listed. If your equipment's code is not listed, visit http://esupport.sony.com/remotecodes for a more comprehensive list. 2 Press and hold , or simultaneously with the button and release. When in the programming mode, the FUNCTION button blinks for approximately 2 30 seconds until a code is entered. 4 3 Enter the five digit code using  -  while the FUNCTION button is lit. If the code is not entered within 30 seconds, you must repeat step 2. 4 Press or to confirm the code. If successfully programmed, the FUNCTION button will blink twice, if not, it blinks five times. VOL MUTING CH JUMP REC RECPAUSE RECSTOP To Confirm the Programming POWER 3 If you can turn your equipment on and off using the green button, the programming is complete. If not, try the next code listed. Note: 4 ■ In some cases, you may not be able to program your remote control. If this is the case, use your equipment's remote control. ■ Any of the FUNCTION buttons can be programmed to operate other equipment regardless of the labeling. For example, if programmed with the correct code, a Blu-ray Disc player can be operated with the button. This is useful if your equipment does not match any of the labeled buttons. BD/DVD TOP MENU MENU F1 F2