Sony MDR-RF995RK Operating Instructions - Page 2
Tips for sound effect - wireless stereo headphone system
View all Sony MDR-RF995RK manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
If you cannot receive a clear audio signal First change the radio frequency with the CHANNEL selector switch on the transmitter, then briefly press the AUTO TUNING button on the headphones. Noise Reduction process The transmitter compresses the audio signal and converts it to RF signal. The headphones convert the received RF signal to an audio signal and decompresses it. This process reduces noise picked up during transmission. Transmitter unit input signal RF transmission Headphones unit output signal dynamic range 2 34 noise level (low) 1 compression decompression 5 The transmitter compresses the audio signals dynamic range, then converts it to RF signal. Noise may occur due to long distance transmission, etc. The headphones convert the RF signal to an audio signal. Noise may occur during conversion. Decompression of the audio signals dynamic range reduces the noise level and improves the S/N (signal-to-noise) ratio. Tips for charging Charge supplied battery first The supplied rechargeable nickel-metal hydride battery is not charged from the first time you use it. Be sure to charge them before use. About auto charge function Placing the headphones on the transmitter automatically turns them off, then charging starts. This eliminates the need for turning on/off every time you wear and take off the headphones. If CHARGE/RED indicator does not light up red --Check if the right and left headphones are rested on the transmitter correctly. Take off the headphones and place them on the transmitter again so that the headphones' contact points meet the transmitter's contact pins. --Charging may not be completed if the transmitter's contact pin and headphones' contact point are dusty. Wipe them with a cotton bud, etc. Charging and usage time Approx. charging time 7 hours2) Maximum usage time1) 20 hours3) 1) at 1 kHz, 0.1 mW + 0.1 mW output 2) hours required to fully charge an empty battery 3) Time may vary, depending on the temperature or conditions of use. To recharge supplied battery after use Place the headphones on the transmitter after use. The CHARGE/RED indicator lights up red, then charging starts. When charging is complete, there is no need to remove the headphones from the transmitter. Remaining battery To check the remaining battery charge of the headphones, turn on the POWER switch and check the POWER indicator. The battery is still serviceable when the indicator lights up green. Charge the headphones if the POWER indicator turns off, dims, flashes, or the sound becomes distorted or noisy. Notes --Insert the AC adaptor plug firmly. --Be sure to use the supplied AC adaptor. Using AC adaptors with different plug polarity or other characteristics can cause product failure. Unified polarity plug --The battery capacity may decrease if the headphones are turned on and placed on the transmitter with the AC adaptor disconnected. --The transmitter automatically turns off while charging the headphones. --This system is designed to charge only the supplied rechargeable battery BP-HP800-11 for safety. Note that other types of rechargeable battery cannot be charged with this system. --If dry batteries are installed, they cannot be charged. --Do not attempt to use the supplied rechargeable battery BP-HP800-11 for other components. It is for use with this system only. --Charge in an environmental temperature of between 5 °C and 35 °C (between 41 °F and 95 °F). --When the battery life reduces to half, this may be the end of battery lifetime. The supplied rechargeable battery BP-HP800-11 is not commercially available. You can order the battery from the store where you purchased this system, or at your nearest Sony dealer. --Do not touch the contact pins of the transmitter. If the contact pins become dirty, charging may not be possible. --Charging may not be completed if the transmitter's contact pins and headphones' contact points are dusty. Wipe them with a cotton bud, etc. Using the headphones with separately-sold dry batteries Commercially available (LR03 (size AAA)) dry batteries can also be used to power the headphones. Install two batteries in the same manner as described in step 1 of "How to use." If you attempt to charge the headphones with dry batteries installed, the CHARGE/RED indicator lights up red for 15 seconds, then turns off. The battery charge function is not activated. Battery life Battery Sony alkaline battery LR03 (size AAA) Approx. usage time1) 24 hours2) 1) at 1 kHz, 0.1 mW + 0.1 mW output 2) Time may vary, depending on the temperature or conditions of use. Note Do not carry a dry battery together with coins or other metallic objects. It can generate heat if the positive and negative terminals of the battery are accidentally come into contact with metallic objects. Tips for connection --When you connect the stereo mini cable (stereo mini jack) directly to an earphone jack (monaural mini jack), the audio signal may not be output through the right channel. Tips for volume setting --If you connect the transmitter to the headphone jack of the A/V component, set the volume of the A/V component as high as possible but not so high that the audio signal becomes distorted. --When watching videos, be careful not to raise the volume too high in quiet scenes. You may hurt your ears when a loud scene is played. Tips for sound effect Slide the switch to select the desired sound effect, OFF or VOICE. Position of switch OFF VOICE Sound effect and suitable sound source Normal playback of the headphones. Produces a clearer announcer's voice. Notes --The volume of the headphones may vary, depending on the input signal and the setting of the EFFECT switch. --The sound effect may not be obtained depending on the input sound sources. Tips for better reception Receiving performance This system utilizes very high frequency signals in the 900 MHz band so the receiving performance may deteriorate due to the surroundings. The following examples illustrate conditions that may reduce the reception range or cause interference. --Inside a building with walls containing steel beams --An area with many steel file cabinets, etc. --An area with many electrical appliances capable of generating electromagnetic fields --The transmitter is placed on a metal instrument. --An area facing a roadway --Noise or interfering signals exist in the surroundings due to radio transceivers in trucks, etc. --Noise or interfering signals exist in the surroundings owing to wireless communication systems installed along roadways. Effective area of the transmitter The optimum distance is up to approximately 45 m (150 ft) without the system picking up some interference. However, the distance may vary depending on the surroundings and environment. --If the system picks up some noise within the above mentioned distance, reduce the distance between the transmitter and the headphones, or select another channel. --When you use the headphones inside the effective area of the transmitter, the transmitter can be placed in any direction from the listener. --Even within the signal reception area, there are some spots (dead spots) where the RF signal cannot be received. This characteristic is inherent to RF signals, and does not indicate malfunction. By slightly moving the transmitter, location of the dead spot can be changed. Replacing the earpads The earpads are replaceable. If the earpads become dirty or worn out, replace them as illustrated below. The earpads are not commercially available. You can order replacements from the store where you purchased this system, or at your nearest Sony dealer. 1 Remove the old earpad by pulling it out of the groove on the housing. 2 Fit the new earpad in the groove of the housing. Make sure the earpad is set to the vertical position. Precautions --When this system is not to be used for a long period of time, disconnect the AC adaptor from the AC outlet holding the plug, and remove the battery from the headphones to avoid damage caused by battery leakage and subsequent corrosion. --Do not leave this system in a location subject to direct sunlight, heat or moisture. --You may hear some noise when you disconnect the AC adaptor from the transmitter before taking off the headphones. --Avoid exposure to temperature extremes, direct sunlight, moisture, sand, dust or mechanical shock. --Please note that water does not splash, this product is not waterproof specification. Notes on headphones To reduce the risk of hearing damage Avoid using headphones at high volume. Hearing experts advise against continuous, loud and extended play. If you experience a ringing in your ears, lower the volume or discontinue use. Caring for others Keep the volume at a moderate level. This will allow you to hear outside sounds and to be considerate to the people around you. If you have any questions or problems concerning the system that are not covered in this manual, please consult your nearest Sony dealer. Be sure to bring the headphones and the transmitter to the Sony dealer when requiring repair work. Troubleshooting If you run into any problems using this system, use the following checklist. Should any problem persist, consult your nearest Sony dealer. No sound/Low sound --Check the connection of the A/V component or the AC adaptor. --Check that the A/V component is turned on. --If you connect the transmitter to an A/V component using the headphone jack, raise the volume level on the connected A/V component within the range where the sound is not distorted. --Change the radio frequency with the CHANNEL selector on the transmitter, then change the radio frequency to that of the transmitter with the AUTO TUNING button on the headphones. --Use the headphones near the transmitter, or change the position of the transmitter. --Charge the supplied rechargeable battery, or replace dry batteries with new ones. If the POWER indicator is still off after charging, take the headphones to a Sony dealer. --Raise the headphone volume. The sound cuts off --The transmitter turns off if no signal or low signal is input for 4 minutes. If you connect the transmitter to an A/V component using the headphone jack, raise the volume level on the connected A/V component within the range where the sound is not distorted. Distorted or intermittent sound (sometimes with noise) --Use the headphones near the transmitter, or change the position of the transmitter. --Do not place the transmitter on a metallic table. --If you connect the transmitter to an A/V component using the headphone jack, lower the volume level on the connected A/V component within the range where the sound is not distorted. --Change the radio frequency with the CHANNEL selector on the transmitter, then change the radio frequency to that of the transmitter with the AUTO TUNING button on the headphones. --Charge the supplied rechargeable battery, or replace dry batteries with new ones. If the POWER indicator is still off after charging, take the headphones to a Sony dealer. Loud background noise --If you connect the transmitter to an A/V component using the headphone jack, raise the volume level on the connected A/V component within the range where the sound is not distorted. --Charge the supplied rechargeable battery, or replace dry batteries with new ones. If the POWER indicator is still off after charging, take the headphones to a Sony dealer. --Do not place the transmitter on a metallic table. --Use the headphones near the transmitter. The POWER/GREEN indicator flashes green --No signal or low signal is input. Start playback of the A/V component, or raise the volume of the connected A/V component within the range where the sound is not distorted, otherwise the transmitter will turn off. If no signal or low signal is input for about 4 minutes, the transmitter turns off automatically. Battery cannot be charged/ CHARGE/RED indicator flashes red, or does not light up red --Check that the right/left of the headphones and transmitter correspond, and put the headphones on the transmitter correctly. --Install the supplied rechargeable nickel-metal hydride battery. Dry batteries and rechargeable batteries other than the supplied cannot be charged. --If the CHARGE/RED indicator does not light up red even though you put the headphones on the transmitter and wait for a while, it may be the end of battery lifetime. You can order the supplied rechargeable battery BP-HP800-11 from the store where you purchased this system, or at your nearest Sony dealer. --Charging may not be completed if the transmitter's contact pin and headphones' contact point are dusty. Wipe them with a cotton bud, etc. Short usage time (the supplied rechargeable battery) --Clean the + and - terminal of the supplied rechargeable battery and the charging terminal of transmitter/ headphone with a dry cloth. --Recharge the supplied rechargeable battery after the fully discharged. Specifications RF stereo transmitter (TMR-RF995R) Modulation FM stereo Carrier frequency 915.5 MHz, 916.0 MHz, 916.5 MHz Channel Ch1, Ch2, Ch3 Transmission distance Approx. 45 m (150 ft) of longest Audio inputs Stereo mini jack Power requirements DC 12 V (from the supplied AC adaptor) Dimensions Approx. 130 mm × 273 mm × 160 mm (5 1/8 × 10 3/4 × 6 3/8 in) (w/h/d) Mass Approx. 265 g (10 oz) Rated power consumption 2.0 W Operating temperature 5°C to 35°C (41°F to 95°F) Wireless stereo headphones (MDR- RF995R) Frequency response 10 Hz - 22,000 Hz Power source Supplied rechargeable nickel-metal hydride battery BP-HP800-11, or commercially available (LR03 (size AAA)) dry batteries Mass Approx. 275 g (10 oz) Operating temperature 5°C to 35°C (41°F to 95°F) Included items RF stereo transmitter TMR-RF995R Wireless stereo headphones MDR-RF995R AC adaptor (12 V) (1) Stereo mini cable (stereo mini plug), 1.5 m (39 3/8 in) (1) Card warranty (1) Operating Instructions (this manual) (1) Design and specifications are subject to change without notice.