Sony MDX-C6500FP Operating Instructions - Page 28

No Mag, No Disc, Ng Discs, Error, Blank, Reset, No Ready, Hi Temp

Page 28 highlights

Radio reception Problem Cause/Solution Preset tuning is not possible. •Store the correct frequency in the memory. •The broadcast signal is too weak. The stations cannot be received. Connect a power antenna control lead (blue) or accessory The sound is hampered by power supply lead (red) to the power supply lead of a car's noises. antenna booster. (Only when your car has built-in FM/AM antenna in the rear/side glass.) Automatic tuning is not possible. The broadcast signal is too weak. t Use manual tuning. The "ST" indication flashes. •Tune in the frequency accurately. •The broadcast signal is too weak. t Set to the MONO mode (page 16). Interference occurs during FM The WIDE mode is selected. reception. t Set the IF mode to IF AUTO (page 16). Error displays (when an optional CD/MD unit is connected) The following indications will flash for about five seconds, and an alarm sound will be heard. Display Cause Solution NO MAG The disc magazine is not inserted in Insert the magazine in the CD/MD the CD/MD unit. unit. NO DISC No disc is inserted in the CD/MD unit. Insert discs in the CD/MD unit. NG DISCS A CD/MD cannot play because of some problem. ERROR*1 A CD is dirty or inserted upside down.*2 An MD does not playback because of some problem.*2 Insert another CD/MD. Clean or insert the CD correctly. Insert another MD. BLANK*1 RESET No tracks have been recorded on an MD.*2 The CD/MD unit cannot be operated because of some problem. Play an MD with recorded tracks on it. Press the reset button on the unit. NO READY The lid of the MD unit is open or the Close the lid or insert the MDs MDs are not inserted properly. properly. HI TEMP The ambient temperature is more than Wait until the temperature goes 50°C (122°F). down below 50°C (122°F). *1 When an error occurs during playback of an MD or CD, the disc number of the MD or CD does not appear in the display. *2 The disc number of the disc causing the error appears in the display. If the above-mentioned solutions do not help improve the situation, consult your nearest Sony dealer. 28Sony Corporation Printed in Korea

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

Error displays
(when an optional CD/MD unit is connected)
The following indications will flash for about five seconds, and an alarm sound will be heard.
Solution
Insert the magazine in the CD/MD
unit.
Insert discs in the CD/MD unit.
Insert another CD/MD.
Clean or insert the CD correctly.
Insert another MD.
Play an MD with recorded tracks
on it.
Press the reset button on the unit.
Close the lid or insert the MDs
properly.
Wait until the temperature goes
down below 50°C (122°F).
Display
NO MAG
NO DISC
NG DISCS
ERROR
BLANK
RESET
NO READY
HI TEMP
Cause
The disc magazine is not inserted in
the CD/MD unit.
No disc is inserted in the CD/MD
unit.
A CD/MD cannot play because of
some problem.
A CD is dirty or inserted upside
down.
*
2
An MD does not playback because of
some problem.
*
2
No tracks have been recorded on an
MD.
*
2
The CD/MD unit cannot be operated
because of some problem.
The lid of the MD unit is open or the
MDs are not inserted properly.
The ambient temperature is more than
50°C (122°F).
*
1
*
1
When an error occurs during playback of an MD or CD, the disc number of the MD or CD does not
appear in the display.
*
2
The disc number of the disc causing the error appears in the display.
If the above-mentioned solutions do not help improve the situation, consult your nearest Sony
dealer.
*
1
Sony Corporation
Printed in Korea
Radio reception
Cause/Solution
•Store the correct frequency in the memory.
•The broadcast signal is too weak.
Connect a power antenna control lead (blue) or accessory
power supply lead (red) to the power supply lead of a car’s
antenna booster. (Only when your car has built-in FM/AM
antenna in the rear/side glass.)
The broadcast signal is too weak.
t
Use manual tuning.
•Tune in the frequency accurately.
•The broadcast signal is too weak.
t
Set to the MONO mode (page 16).
The WIDE mode is selected.
t
Set the IF mode to IF AUTO (page 16).
Problem
Preset tuning is not possible.
The stations cannot be received.
The sound is hampered by
noises.
Automatic tuning is not
possible.
The “ST” indication flashes.
Interference occurs during FM
reception.