Sony MHC-GX20 Operating Instructions - Page 14

Setting presets through, manual tuning, Other Operations, Presetting radio stations continued

Get Sony MHC-GX20 - Mini Stereo PDF manuals and user guides View all Sony MHC-GX20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Presetting radio stations (continued) Setting presets through manual tuning 1 Press TUNER/BAND repeatedly to select "FM" or "AM". 2 Press m or M (or TUNING - or + on the remote) repeatedly to tune in the desired station. 3 Press TUNER MEMORY on the remote. A preset number appears in the display. The stations are stored from preset number 1. 4 Press . or > (or PRESET - or + on the remote) repeatedly to select the desired preset number. 5 Press ENTER on the remote. 6 Repeat steps 1 to 5 to store other stations. Other Operations To Do this Tune in a station Follow the procedure described in with a weak "Setting presets through manual signal tuning". Set another station to an existing preset number Start over from step 1. After step 3, press . or > (or PRESET - or + on the remote) repeatedly to select the preset number you want to store the other station. To change the AM tuning interval (except for the European and Middle Eastern models) The AM tuning interval is factory-set to 9 kHz (10 kHz in some areas). To change the AM tuning interval, tune in any AM station first, then turn off the system. While holding down TUNER/BAND, turn the system back on. When you change the interval, all the AM preset stations are erased. To reset the interval, repeat the same procedure. Note You cannot change the AM tuning interval in the Power Saving Mode. Tips • The preset stations are retained for half a day even if you disconnect the mains lead or if a power failure occurs. • To improve broadcast reception, reorient or move the supplied antenna near a window or outdoors. 14GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
14
GB
Setting presets through
manual tuning
1
Press TUNER/BAND repeatedly to
select “FM” or “AM”.
2
Press
m
or
M
(or TUNING – or + on
the remote) repeatedly to tune in the
desired station.
3
Press TUNER MEMORY on the remote.
A preset number appears in the display.
The stations are stored from preset number
1.
4
Press
.
or
>
(or PRESET –
or +
on the remote) repeatedly to select the
desired preset number.
5
Press ENTER on the remote.
6
Repeat steps 1 to 5 to store other
stations.
Presetting radio stations (continued)
Other Operations
To
Do this
Follow the procedure described in
“Setting presets through manual
tuning”.
Start over from step 1. After step
3, press
.
or
>
(or PRESET
– or + on the remote) repeatedly to
select the preset number you want
to store the other station.
To change the AM tuning interval
(except for the European and Middle
Eastern models)
The AM tuning interval is factory-set to 9 kHz
(10 kHz in some areas). To change the AM
tuning interval, tune in any AM station first,
then turn off the system. While holding down
TUNER/BAND, turn the system back on.
When you change the interval, all the AM
preset stations are erased. To reset the interval,
repeat the same procedure.
Note
You cannot change the AM tuning interval in the
Power Saving Mode.
Tips
•
The preset stations are retained for half a day even
if you disconnect the mains lead or if a power
failure occurs.
•
To improve broadcast reception, reorient or move
the supplied antenna near a window or outdoors.
Tune in a station
with a weak
signal
Set another
station to an
existing preset
number