Sony NWZ-W273SBLK Quick Start Guide - Page 1

Quick Start Guide How to Install the Supplied Software How to Use Your "WALKMAN" NWZ-W273S/W274S Access to the online Help Guide (Full version). http://rd1.sony.net/help/dmp/nwzw270s/en/ About the manuals This Quick Start Guide only describes the basic operating instructions and how to install the supplied software. For detailed information and operating instructions, refer to the Help Guide (HTML document) included in the supplied software after installation. Contents Please check the items in the package. ÿÿ"WALKMAN" (1) ÿÿUSB cradle (1) ÿÿEarbuds (1 set) ÿÿSwimming earbuds (1 set) ÿÿAdjustment band (1) ÿÿQuick Start Guide (this manual) ÿÿUsing your Walkman while Swimming About the Operating System Make sure that the OS is Windows XP*1 (Service Pack 3 or later), Windows Vista*2 (Service Pack 2 or later), Windows 7*2 (Service Pack 1 or later), or Windows 8. *1 Excluding 64-bit OS versions. *2 [Compatibility mode] for Windows XP is not supported. For a Mac computer, make sure that the OS is Mac OS X v10.6 or later. Not supported by OSs other than above Attaching Your Walkman to the USB Cradle (Supplied) and Charging the Battery To connect your Walkman to a computer, the Walkman must be attached to the USB cradle correctly. 1 Dry the terminals of your Walkman () using a soft dry cloth if needed. 2 Attach your Walkman to the USB cradle. Make sure that the terminals of your Walkman () and the USB cradle () are in contact with each other. 3 Connect your Walkman to an operating computer using the USB cradle. ˎˎ If a screen appears presenting a choice of actions, click "Cancel." Charging starts. ˎˎ Make sure that the OPR lamp window on the USB cradle lights up in red. OPR lamp Notes on charging by using the computer ˎˎCharge the battery when the OPR lamp blinks in red rapidly. ˎˎWhile the battery is charging, the OPR lamp indicates the charging status of your Walkman. You can see the status of the OPR lamp through the OPR lamp window on the USB cradle. Lights up in red: Being charged Turns off: Charged fully or not being charged ˎˎCharging time is approx. 1.5 hours. When your Walkman has been fully charged, disconnect it from the computer. For a Mac computer, click the eject icon of [WALKMAN] in the sidebar of Finder to disconnect your Walkman. ˎˎThe Walkman will not charge if the computer enters a power saving mode such as Sleep or Hibernate, and will discharge in this case. ˎˎWhen you use your Walkman for the first time, or if you have not used the Walkman for a long time, it may take a few minutes to be recognized by the computer, even if charging has already started (the OPR lamp lights up in red). Check that the computer recognizes your Walkman after you have connected it to the computer for about 5 minutes. How to Install the Supplied Software Installing WALKMAN Guide and Media Go (for Windows) 1 Connect your Walkman to a running computer using the USB cradle (supplied). 2 Select the following order with the computer.  Windows 7 or earlier: Select [Start] - [Computer] or [My Computer] - [WALKMAN] - [Storage Media] - [FOR_WINDOWS].  Windows 8: Select [Desktop] from [Start screen] to open [File Explorer]. In the [Computer] list, select [WALKMAN] - [Storage Media] - [FOR_WINDOWS]. 3 Double-click [Setup.exe]. The install wizard appears. ˎˎ When you execute [Setup.exe], the [Setup.exe] file stored in the [FOR_WINDOWS] folder of your Walkman is copied to your computer for backup, and WALKMAN Guide and Media Go are installed to your computer. ˎˎ If [Setup.exe] does not start, copy the [Setup.exe] file to your desktop, then double-click it. 4 Follow the on-screen instructions. After the install wizard finishes, the WALKMAN Guide and Media Go shortcuts appear on the desktop of your computer. The Help Guide is included in the WALKMAN Guide. Installing the Help Guide and the Content Transfer software (for Mac) 1 Connect your Walkman to a running computer using the USB cradle (supplied). 2 On the computer, select [WALKMAN] in the sidebar of Finder, then open the [FOR_MAC] folder. 3 Double-click the installer icon of the desired software: To install the Help Guide:[Help_Guide_Installer_for_Mac] To install the Content Transfer software: [ContentTransfer. pkg] 4 Follow the on-screen instructions. After the installer finishes, the alias (shortcut) of the installed software (Help Guide or the Content Transfer software) appears on the desktop of your computer.  Hint ˎˎBefore you attempt to delete the software from your Walkman, copy the [FOR_MAC] folder to your Mac computer as a backup if necessary. Parts and Controls  Tactile dot  Terminals  Neckband  OPR (Operation) lamp  Earbud  Power lock switch  Headphone section   (Power) button  P .LIST (Playlist)/ SHUF (Shuffle) button  VOL +*1/- button  Previous button  Next button  RESET button   button*1 *1 There are tactile dots. Use them to help with button operations. ©2013 Sony Corporation Printed in Malaysia 4-476-039-12(1)