Sony SA-VE315 Operating Instructions - Page 11

Specifications, Troubleshooting

Page 11 highlights

Troubleshooting Specifications Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. • Make sure all the connections have been correctly made. • Make sure the volume on the amplifier has been turned up properly. • Make sure the program source selector on the amplifier is set to the proper source. • Check if headphones are connected. If they are, disconnect them. There is distortion in the subwoofer sound output. • Check if any sound-enhancing functions have been activated on the amplifier. If they have, turn them off. There is hum or noise in the speaker output. • Make sure all the connections have been correctly made. • Make sure none of the audio components are positioned too close to the TV set. The sound has suddenly stopped. • Make sure all the connections have been correctly made. Contact between bare speaker wires at the speaker terminals may cause a short-circuit. SA-VE315/VE312 For the U.S. model AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: with 6 ohm loads both channels driven, from 20 - 150 Hz; rated 75 watts per channel minimum RMS power, with no more than 0.8% total harmonic distortion from 250 milliwatts to rated output. SS-V315 (front and rear speakers) Speaker system Full range, magnetically shielded Speaker units 5 × 10 cm (2 × 4 in.), cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 100 watts Sensitivity level 87 dB (1 W, 1 m) Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 68 × 150 × 125 mm (2 3/4 × 6 × 5 in.), including front grille Mass European model: Approx. 640 g (1 lb 7 oz) each Other models: Approx. 740 g (1 lb 10 oz) each SS-CN315 (center speaker) Speaker system Full range × 2, magnetically shielded Speaker units 5 × 10 cm (2 × 4 in.), cone type Enclosure type Bass reflex Rated impedance 8 ohms Power handling capacity Maximum input power: 120 watts Sensitivity level 89 dB (1 W, 1 m) Frequency range 90 Hz - 20,000 Hz Dimensions (w/h/d) Approx. 301 × 68 × 125 mm (11 7/8 × 2 3/4 × 5 in.), including front grille Mass European model: Approx. 1.4 kg (3 lb 1 oz) Other models: Approx. 1.5 kg (3 lb 5 oz) continued 11GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

11
GB
Specifications
SA-VE315/VE312
For the U.S. model
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
with 6 ohm loads both channels driven, from
20 - 150 Hz; rated 75 watts per channel
minimum RMS power, with no more than
0.8% total harmonic distortion from
250 milliwatts to rated output.
SS-V315 (front and rear speakers)
Speaker system
Full range, magnetically
shielded
Speaker units
5
×
10 cm (2
×
4 in.),
cone type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
100 watts
Sensitivity level
87 dB (1 W, 1 m)
Frequency range
90 Hz - 20,000 Hz
Dimensions (w/h/d)
Approx. 68
×
150
×
125 mm (2
3
/
4
×
6
×
5 in.),
including front grille
Mass
European model:
Approx. 640 g (1 lb 7 oz)
each
Other models:
Approx. 740 g (1 lb 10 oz)
each
SS-CN315 (center speaker)
Speaker system
Full range
×
2,
magnetically shielded
Speaker units
5
×
10 cm (2
×
4 in.),
cone type
Enclosure type
Bass reflex
Rated impedance
8 ohms
Power handling capacity
Maximum input power:
120 watts
Sensitivity level
89 dB (1 W, 1 m)
Frequency range
90 Hz - 20,000 Hz
Dimensions (w/h/d)
Approx. 301
×
68
×
125 mm (11
7
/
8
×
2
3
/
4
×
5 in.), including front
grille
Mass
European model:
Approx. 1.4 kg (3 lb 1 oz)
Other models:
Approx. 1.5 kg (3 lb 5 oz)
Troubleshooting
Should you encounter a problem with your
speaker system, check the following list and
take the indicated measures.
If the problem
persists, consult your nearest Sony dealer.
There is no sound from the speaker
system.
Make sure all the connections have been
correctly made.
Make sure the volume on the amplifier
has been turned up properly.
Make sure the program source selector on
the amplifier is set to the proper source.
Check if headphones are connected.
If
they are, disconnect them.
There is distortion in the subwoofer sound
output.
Check if any sound-enhancing functions
have been activated on the amplifier.
If
they have, turn them off.
There is hum or noise in the speaker
output.
Make sure all the connections have been
correctly made.
Make sure none of the audio components
are positioned too close to the TV set.
The sound has suddenly stopped.
Make sure all the connections have been
correctly made.
Contact between bare
speaker wires at the speaker terminals
may cause a short-circuit.
continued