Sony SAL1635Z Operating Instructions - Page 1
Sony SAL1635Z - 16-35mm f/2.8 ZA Lens Manual
UPC - 027242714267
View all Sony SAL1635Z manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
4-115-113-01(1) 12 3 7 Lens for Digital Single Lens Reflex Camera/Objectif pour appareil photo numérique reflex à objectifs interchangeables/ 4 6 5 8 Operating Instructions/Mode d'emploi/Manual de instrucciones/ Vario-Sonnar T 16-35mm F2.8 ZA SSM Vario-Sonnar T 24-70mm F2.8 ZA SSM SAL1635Z/SAL2470Z -1 ©2008 Sony Corporation (1) (2) -2 Printed in Japan པ͢Δɻ Γ·͢ɻ Vario-Sonnar T 24-70mm F2.8 ZA SSMͷΈ)ɻ KK-CA 1 2 3 4 5 6 7 8 1 1)ɺ(2)ͷ2 2 2 ͍ͩ͞ɻ Δɻ AF MF Γସ͑ AF MF AF AFʹ͠ ઃఆ͕MFͷ߹ɺMFʹͳΓ·͢ɻ AF·ͨMF • MF AF/MF • AF࣌ʹMF AFͷͱ͖ ʹɺAF/MF • MF࣌ʹAF MF AFͷ ͱ͖ʹɺAF/MF DMF) AF AF-A AF(AF-S DMF͕࡞ DMF AF(AF-C AF-A 2 MF MF Γ͍ͩ͘͞ɻ ͍ɻ 1ؒͰ͢ɻ English This manual is for use with several different lenses. This lens is designed for Sony cameras. This lens was developed jointly by Carl Zeiss and Sony Corporation and designed for Sony mount cameras. This lens is produced according to the strict standards and quality assurance system of Carl Zeiss. WARNING To reduce fire or shock hazard, do not expose the unit to rain or moisture. Do not directly look at the sun through this lens. Doing so might harm your eyes or cause loss of eyesight. Keep the lens out of reach of small children. There is danger of accident or injury. For the customers in the U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. For the customers in Canada This Class B digital apparatus complies with Canadian ICES-003. For the customers in Europe Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems) This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product. Notice for the customers in the countries applying EU Directives The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minatoku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents. Notes on use • Do not leave the lens in direct sunlight. If sunlight is focused onto a nearby object, it may cause a fire. If circumstances necessitate leaving the lens in direct sunlight, be sure to attach the lens cap. • Be careful not to subject the lens to mechanical shock while attaching it. • Always place the lens caps on the lens when storing. • Do not keep the lens in a very humid place for a long period of time to prevent mold. • Hold both the camera and lens, when you carry the camera with the lens attached. • Do not hold the camera by the lens part extended for zooming (For Vario-Sonnar T 24-70mm F2.8 ZA SSM only). • Do not touch the lens contacts. If dirt, etc., gets on the lens contacts, it may interfere or prevent the sending and receiving of signals between the lens and the camera, resulting in operational malfunction. Precaution for flash use When using a built-in camera flash, make sure to remove the lens hood. With certain of lens/flash combinations, the lens may partially block the light of the flash, resulting in a shadow at the bottom of the picture. Vignetting When you use lens, the corners of the screen become darker than the center. To reduce this phenomena (called vignetting), close the aperture by several stops. Condensation If your lens is brought directly from a cold place to a warm place, condensation may appear on the lens. To avoid this, place the lens in a plastic bag or something similar. When the air temperature inside the bag reaches the surrounding temperature, take the lens out. Cleaning the lens • Do not touch the surface of the lens directly. • If the lens gets dirty, brush off dust with a lens blower and wipe with a soft, clean cloth (Cleaning Cloth KK-CA (optional) is recommended). • Do not use any organic solvent, such as thinner or benzine, to clean the lens or the camera cone. Names of parts 1···Focusing ring 2···Distance index 3···Zooming ring 4···Lens contacts 5···Mounting index 6···Distance scale 7···Focus-hold button 8···Focus-mode switch Attaching/detaching the lens To attach the lens (See illustration -.) 1 Remove the rear and front lens caps and the camera body cap. • You can attach/detach the front lens cap in two ways, (1) and (2). When you attach/detach the lens cap with the lens hood attached, use method (2). 2 Align the orange index on the lens barrel with the orange index on the camera (mounting index), then insert the lens into the camera mount and rotate it clockwise until it locks. • Do not press the lens release button on the camera when mounting the lens. • Do not mount the lens at an angle. To remove the lens (See illustration -.) While pressing and holding the lens release button on the camera, rotate the lens counterclockwise until it stops, then detach the lens. Attaching lens hood It is recommended that you use a lens hood to reduce flare and ensure maximum image quality. Align the red line on the lens hood with the red dot on the lens. Turn the hood clockwise until the red dot on the hood meets the red dot on the lens and it clicks into place. • When using a built-in camera flash, make sure to remove the lens hood to avoid blockage of the flash light. • If a marking (red line, red dot, etc.) is provided, attach the lens hood properly. Otherwise, the lens hood may interfere with the desired effect or may appear in pictures. • When storing, turn over the lens hood and place it onto the lens backwards. Zooming Rotate the zooming ring to the desired focal length. Focusing To switch AF (auto focus)/MF (manual focus) The focus mode can be switched between AF and MF on the lens. For AF photography, both the camera and lens should be set to AF. For MF photography, either or both the camera or lens should be set to MF. To set the focus mode on the lens (See illustration -.) Slide the focus-mode switch to the appropriate mode, AF or MF. • In MF, turn the focusing ring to adjust the focus while looking through the viewfinder (See illustration -). The focus signal in the viewfinder indicates the current condition of the focus. To use a camera equipped with an AF/MF control button • Press the AF/MF control button to switch AF to MF when both the camera and lens are set to AF. • Press the AF/MF control button to switch MF to AF when the camera is set to MF and the lens is set to AF. Direct manual focus (DMF) Rotate the focusing ring to set correct DMF when the focus is locked in AF-A (automatic auto focus) or AF-S (single-shot auto focus). • DMF is not available in the following cases: - When the image is out of focus - When AF-C (continuous auto focus) is selected - When the focus is confirmed for the second photo during continuous recording in AF-A Shooting at infinity in MF The focusing mechanism turns slightly past infinity to provide accurate focusing under various operating temperatures. Always confirm the image sharpness through the viewfinder, especially when the lens is focused near infinity. Focus-hold button (See illustration -.) While the focus-hold button is pressed, auto focus function is suspended and the focus is fixed for shooting. • The function of the focus-hold button can be changed on cameras with custom function capability. Refer to the camera manuals for details. ओͳ༷ ໊ Vario-Sonnar T 16-35mm F2.8 ZA SSM (SAL1635Z) Vario-Sonnar T 24-70mm F2.8 ZA SSM (SAL2470Z) 35mm 1 (mm) 24-52.5 36-105 13-17 13-17 ը֯1*2 ը֯2*2 ࠷ 3 (m) (ഒ) ࠷খߜΓ (ܘmm mm) ࣭ྔ(g) 107ƅ-63ƅ 83ƅ-44ƅ 0.28 0.24 F22 77 83ʷ114 860 84ƅ-34ƅ 61ƅ-23ƅ 0.34 0.25 F22 77 83ʷ111 955 *1 ͜͜Ͱͷ35mm APS-C 2 ը֯135mm 2APS-C 3 ADIௐޫʣΛADI ͢ɻ 1 1 1 1 1 Specifications Name (Model name) Equivalent 35mm-format focal length*1 (mm) Lens groupselements Angle of view 1*2 Angle of view 2*2 Minimum focus*3 (m (feet)) Maximum Minimum magnification f-stop (×) Filter diameter (mm) Dimensions (maximum diameter × height) (mm (in.)) Mass (g (oz.)) Vario-Sonnar T 16-35mm F2.8 ZA SSM (SAL1635Z) 24-52.5 13-17 107°-63° 83°-44° 0.28 (0.92) 0.24 f/22 77 Approx. 83×114 Approx. 860 (3 3/8×4 1/2) (30 3/8) Vario-Sonnar T 24-70mm F2.8 ZA SSM (SAL2470Z) 36-105 13-17 84°-34° 61°-23° 0.34 (1.1) 0.25 f/22 77 Approx. 83×111 Approx. 955 (3 3/8×4 3/8) (33 1/4) *1 The value for equivalent 35mm-format focal length is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized image sensor. *2 The value of angle of view 1 is based on 35mm-format cameras, and that of angle of view 2 is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized image sensor. *3 Minimum focus is the shortest distance from the image sensor to the subject. • This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI. • Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused at infinity. Included items: Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Lens case (1), Set of printed documentation Designs and specifications are subject to change without notice. is a trademark of Sony Corporation. Company names and company product names are trademarks or registered trademarks of those companies.