Sony SLV-669HF Operating Instructions - Page 9

A/V hookup, Getting Started

Get Sony SLV-669HF PDF manuals and user guides View all Sony SLV-669HF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Getting Started t t A/V hookup: VCR setup After you've connected your TV and completed antenna or cable hookup, use the following procedure to set up the VCR. Press MENU and select ADVANCED OPTIONS. TIMER SET/CHECK SETTINGS ADVANCED OPTIONS , Set AUTO ANT SELECT to OFF and press OK. ADVANCED OPTIONS AUTO ANT SELECT AUTO STEREO TUNER AUDIO APC TAPE SELECT AUTO TAPE SPEED SHARPNESS 3RETURN ON OFF ON AUTO ON L H t t SELECT : SET : O K QUIT : MENU SELECT : SET : O K QUIT : MENU For details, see page 54. Caution Connections between the VCR's VHF/UHF connector and the antenna terminals of the TV receiver should be made only as shown in the following instructions. Failure to do so may result in operation that violates the regulations of the Federal Communications Commission regarding the use and operation of RF devices. Never connect the output of the VCR to an antenna or make simultaneous (parallel) antenna and VCR connections at the antenna terminals of your receiver. Note to CATV system installer (in USA) This reminder is provided to call the CATV system installer's attention to Article 82040 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. continued Getting Started 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
9
Getting Started
Getting Started
A/V hookup:
VCR setup
After you’ve connected your TV and completed antenna or cable hookup,
use the following procedure to set up the VCR.
Caution
Connections between the VCR’s VHF/UHF connector and the antenna terminals of
the TV receiver should be made only as shown in the following instructions. Failure to
do so may result in operation that violates the regulations of the Federal
Communications Commission regarding the use and operation of RF devices.
Never
connect the output of the VCR to an antenna or make simultaneous (parallel) antenna
and VCR connections at the antenna terminals of your receiver.
Note to CATV system installer (in USA)
This reminder is provided to call the CATV system installer’s attention to Article 820-
40 of the NEC that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
continued
Press MENU and select
ADVANCED OPTIONS.
Set AUTO ANT SELECT
to OFF and press OK.
For details, see page 54.
SELECT
SET
QUIT
:
:
:
TIMER
SET/CHECK
SETTINGS
ADVANCED
OPTIONS
O K
MENU
t
t
,
SELECT
SET
QUIT
:
:
:
ADVANCED
OPTIONS
O K
MENU
t
t
3
RETURN
AUTO
ANT
SELECT
AUTO
STEREO
TUNER
AUDIO
TAPE
SELECT
AUTO
TAPE
SPEED
SHARPNESS
APC
ON
OFF
ON
AUTO
ON
L
H