Sony SNC-CS20 Installation Manual - Page 2
Installation, Connection, Specifications - specifications
View all Sony SNC-CS20 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
1 Shoulder screw NETWORK POWER IRIS CLASS 2 Fall-prevention wire rope 2 Focus assist indicator 1 2 SEE INSTRUCTION MANUAL LAN 12 3456 Network cable (straight, not supplied) CLASS 2 WIRING - 1 DC 12V AC 24V + 2 10BASE-T/ 100BASE-TX Router or hub Installation Caution Request for an expert to install it to the ceiling. Attaching the fall-prevention wire rope When you install the camera on a ceiling or a high position, be sure to attach the supplied fall-prevention wire rope to prevent the camera from falling. Attach the fall-prevention wire rope to the screw hole on the rear of the camera, as in the illustration. Note Take care not to short-circuit the power terminal or the cable with the wire rope when you attach it. 1 Secure the wire rope to the junction box on the ceiling. Use a screw to match the screw hole of your junction box (not supplied). 2 Secure the wire rope to the wire rope mounting screw hole on the rear of the camera using the supplied shoulder screw. Caution Use the supplied screws for installation. If not, the wire rope may not function properly. Focus Assist Function 1 Select the camera operation mode to match the video monitor in use with the VIDEO OUT selector. 2 Set the iris to open with the IRIS selector. The IRIS OPEN indicator and the focus assist indicator appear on the monitor screen. The length of bar varies according to the degree of focus adjustment. Bar indicates the peak hold value. 3 Turn the focus ring until bar reaches the peak hold value . Release the lens connector 1 Remove the screw. 2 Pull out the lens connector cover as shown to release the lens connector and then tighten the screw. Connection Connecting to the Network Connect the LAN cable of the camera to a router or hub in the network using the network cable (straight, not supplied). To connect to a computer Connect the LAN cable of the camera to the network connector of a computer using the network cable (cross, not supplied). Connecting the Power Source There are three ways to supply power to this camera, as follows. 12 V DC 24 V AC Power supply equipment pursuant to IEEE802.3af (PoE* system) *PoE means Power over Ethernet. Note If the power is supplied from the power input cable and LAN cable at the same time, the power from the LAN cable has priority over the other. Connecting to 12 V DC or 24 V AC source Connect the power input cable of the camera to a 12 V DC or 24 V AC source. Use a 12 V DC or 24 V AC source isolated from 100 to 240 V AC. The acceptable voltage ranges for each are as follows. 12 V DC: 10.8 V to 13.2 V 24 V AC: 21.6 V to 26.4 V Use UL cable (VW-1 style 1007) for these connections. Connecting to the power supply equipment pursuant to IEEE802.3af The power supply equipment pursuant to IEEE802.3af supplies the power through the LAN cable. For details, refer to the Instruction Manual of the equipment. Connecting the I/O Cable Connect the wires of the I/O cable as follows: Wiring diagram for sensor input Mechanical switch/open collector output device Camera inside 3.3 V 2.2 kohms Outside 6 (Sensor In +) 5 (GND) GND Mechanical switch or Open collector output device Wiring diagram for alarm output Camera inside 2 or 4 (Alarm Output +) Magnet relay 24 V AC/24 V DC, 1 A or less 1 or 3 (Alarm Output -) Outside 5 V Circuit example R GND Specifications Compression Video compression format Audio compression format Maximum frame rate JPEG/MPEG4 G.711/G.726 (40, 32, 24, 16 kbps) 30 fps Camera SNC-CM120 Signal system NTSC color system/PAL color system (switchable) Image device 1/3 type interline transfer (ExwavePRO) CCD Total picture elements: Approx. 1,320,000 Effective picture elements: Approx. 1,250,000 Synchronization Internal synchronization Horizontal resolution 600 TV lines (analog video) Video S/N (AGC 0 dB) 50 dB or more Minimum illumination (F1.3, 50 IRE) 0.6 lx (AGC 30 dB, normal readout), 0.1 lx (AGC 36 dB, Light funnel ON) Camera SNC-CS20 Signal system NTSC color system/PAL color system (switchable) Image device 1/4 type interline transfer (ExwavePRO) CCD Total picture elements: Approx. 350,000 Effective picture elements: Approx. 330,000 Synchronization Internal synchronization Horizontal resolution 400 TV lines (analog video) Video S/N (AGC 0 dB) 50 dB or more Minimum illumination (AGC 36 dB, F1.0, 50 IRE) 0.2 lx Lens (standard equipment of SNC-CM120) Focal length 2.8 to 6 mm Maximum relative aperture F1.3 View angle Vertical: 74.2° to 35.2° Horizontal: 101.2° to 47.0° Minimum object distance 300 mm (11 7/8 inches) Lens (standard equipment of SNC-CS20) Focal length 3 mm to 8 mm Maximum relative aperture F1.0 View angle Vertical: 49.3° to 20.2° Horizontal: 66.6° to 27.0° Minimum object distance 200mm (7 7/8 inches) Interface LAN port 10BASE-T/100BASE-TX, auto negotiation (RJ-45) I/O port Sensor input : × 1, make contact, break contact Alarm output : × 2, 24 V AC/DC, 1 A (mechanical relay outputs electrically isolated from the camera) Video output VIDEO OUT: BNC, 1.0 Vp-p, 75 ohms, unbalanced, sync negative Microphone input* Minijack (monaural) Plug-in-power supported (rated voltage: 2.5 V DC) Line input* Minijack (monaural) * The microphone input and the line input are switchable with a selector. Line output Minijack (monaural), Maximum output level: 1 Vrms Others Power supply Power consumption Operating temperature Storage temperature Operating humidity Storage humidity Dimensions (w/h/d) Mass Supplied accessories 12 V DC ± 10% 24 V AC ± 10%, 50/60 Hz IEEE802.3af compliant (PoE system) SNC-CM120: 9W max. SNC-CS20: 7.5W max. -10 °C to +50 °C (22 °F to 122 °F) -20 °C to +60 °C (-4 °F to +140 °F) 20 to 80 % 20 to 95 % 82.5 × 63 × 135 mm (3 1/4 × 2 1/2 × 5 3/10 inches), not including the projecting parts Approx. 610 g (1 lb 5 1/2 oz) (SNC-CM120),with lens not including the accessories Approx. 600 g (1 lb 5 oz) (SNC-CS20),with lens not including the accessories CD-ROM (Users Guides, Easy Setup Guides and supplied programs) (1) Fall-prevention wire rope (1) Shoulder screw M4 (1) Installation Manual (this document) (1) B&P Warranty Booklet (1) Warranty Sheet (1) Design and specifications are subject to change without notice. 63 (2 1/2) 62 (2 1/2) 63 (2 1/2) 62 (2 1/2) Front (SNC-CM120) 82.5 (3 1/4) Front (SNC-CS20) 82.5 (3 1/4) Side (SNC-CM120) 52.3 (2 1/8) 135 (5 3/8) 67 (2 3/4) Unit: mm (inches) 67 (2 3/4) Side (SNC-CS20) 42 (1 5/8) 135 (5 3/8) 67 (2 3/4) 67 (2 3/4) Unit: mm (inches)