Sony SNCEP520 Installation Guide (SNC-ER/EP Install Manual) - Page 2

 ø130 (5 1/8) 3-Screw hole  Camera (When installing the ceiling bracket) ø147.4 (5 7/8) 190.9 (7 5/8) (When installing the bracket) 190 (7 1/2) (Camera unit only) 132 (5 1/4) (When installing the bracket) 120° 45° 9 /32) 83.5 (3 120° 120°  How to install 1 Hook Align the triangular mark with the front side of the camera when using a junction box. ø40 (1 5/8) Cable hole Unit: mm (inches) Celing bracket Ceiling bracket Ceiling Built-in wire rope 45° 85.7 (3 3/8) 83.5 (3 9/32) Unit: mm (inches) 85.7 (3 3/8) 83.5 (3 9/32) Hole 13-ø4.5 (3/16) ø130 1 (5 /8) 120° Unit: mm (inches) 2 Align the triangular mark on the camera with the diamondshaped mark on the ceiling bracket.  Ceiling bracket Ceiling Screw (supplied) LAN 24 V AC I/O cable SD memory card Mic Audio Input Output 10BASE-T/ 100BASE-TX Network cable (straight, not supplied) Hub Network Install a hub compatible with HPoE when using an HPoE system. Installation Notes  Do not grasp the camera head when carrying the camera.  Do not turn the camera head manually. Doing so will likely result in the camera malfunctioning.  Turn off the power of the camera before installing it. Install the camera to a horizontal place. If you have to install the camera to an incline, make sure the incline is within ±15° to the horizontal level to ensure the turning performance of the camera. Installing the Camera on a Ceiling  Use the supplied ceiling bracket to install the camera. The ceiling bracket is attached to the camera unit. Remove it before installing. Warning  If you attach the camera in a high location such as wall or ceiling, etc., entrust the installation to an experienced contractor or installer.  If you install the camera in a high location, ensure that the ceiling is strong enough to withstand the weight of the camera plus mounting brackets and screws, and then install the camera securely. If the ceiling is not strong enough, the camera may fall and cause serious injury.  To prevent the camera from falling, make sure to attach the built-in wire rope.  If you attach the camera to the ceiling, check periodically, at least once a year, to ensure that the connection has not loosened. If conditions warrant, make this periodic check more frequently. Before installation  Decide the direction in which the camera will shoot, before making holes for wiring and screw holes.  Push down the perforated tab to bundle the cables from the side of the camera. (For details, see " Cable cover" in "Location and Function of Part.") Installing directly on a ceiling Using the supplied template, make a hole for the wiring (ø40 mm (1 5/8 inches)). Determine the location of the three screw holes for attaching the ceiling bracket. () Using the existing junction box Attach the ceiling bracket to the junction box. Screws for this operation are not supplied. Attach the ceiling bracket in a manner that the triangular mark faces the front side of the camera. Fixing screws Required screws (not supplied) vary in accordance with the location or material of the installation. For steel: Fix with M4 screws and nuts. For wood: Fix with tapping screws (nominal diameter 4). A material thickness of 15 mm (19/32 inches) or more is necessary. For a concrete wall: Fix with dry bit or plug bolts. For a junction box: Fix with screws that accommodate the screw holes in the junction box. Warning Use the appropriate screws in accordance with the condition and material of the location site. Otherwise, the ceiling unit may fall and cause serious injury. How to install 1 Put the built-in wire rope on the hook in the ceiling bracket. (-1) 2 Connect the cables. Note Although you can connect the cables while the camera unit is hanging from the ceiling bracket with the help of the rope, be sure not to put additional pressure on the unit. 3 Align the triangular mark on the camera with the diamond-shaped mark on the ceiling bracket, and then attach the camera unit into the bracket. (-2) 4 Rotate the camera unit in a clockwise direction. 5 Attach the camera unit to the ceiling bracket by fixing two screws at both sides of the unit. 6 Attach the cable cover. Note Use the supplied screws to install the unit. Using other screws may cause damage inside the unit. How to remove the camera 1 Loosen and remove the two screws on both sides of the camera unit. 2 Rotate the camera unit in a counterclockwise direction, and remove it from the ceiling bracket. 3 Disconnect the cables. Note Although you can disconnect the cables while the camera unit is hanging from the ceiling bracket with the help of the rope, be sure not to put additional pressure on the unit. 4 Unhook the built-in wire rope from the ceiling bracket, and dismount the camera unit. Note Always hold the camera when you dismount the camera unit. This will prevent any risk of the camera falling. Install the camera with its head facing upward Follow the same steps as in "Installing the Camera on a Ceiling" when installing or removing the camera. Be sure to place the camera securely to prevent it from falling. Note By default, the images from the camera are displayed normally when the camera is installed on the ceiling. To display the images from the camera in correct way when you place the camera on the desk top, use the E.flip function.  For the setting of the E.flip function, see the User's Guide stored in the supplied CD-ROM. Connection Connecting to the Network  Connect the LAN port of the camera unit to a router or hub in the network using the network cable (straight, not supplied). To connect to a computer Connect the LAN port of the camera unit to the network connector of a computer using the network cable (cross, not supplied). Connecting the Power Source  The following two methods are available for connecting to a power source.  24 V AC  HPoE Note If you use this camera by feeding power to the LAN port, use the HPoE power feeding device. Connecting to a 24 V AC power source supply Connect the 24 V AC power supply system to the power input terminal of the camera.  Use a 24 V AC power source isolated commercial power supply.  The usable voltage range is as follows: 24 V AC: 21.6 to 26.4 V  Use a UL cable (VW-1 style 10368) for 24 V AC connection. Recommended power cable 24 V AC Cable(AWG) Maximum cable length (m (feet)) #24 11 (36.1) #22 19 (62.3) #20 28 (91.9) Connecting to the power supply equipment pursuant to IEEE802.3at The power supply equipment pursuant to IEEE802.3at supplies the power through the LAN cable. For details, refer to the Instruction Manual of the equipment. Connecting the I/O Cable Wiring diagram for sensor input Mechanical switch/open collector output device Camera inside 3.3 V Outside 10 kohms 2.2 kohms 10 kohms 3 or 1 pin (Alarm Input 1 or 2) 10 kohms Mechanical switch or GND GND GND 2 or 4 pin GND Wiring diagram for alarm output Camera inside Outside 24 V DC Open collector output device R 5 pin (Alarm Output +) Magnet relay 24 V AC 24 V DC, 1 A or less 6 pin (Alarm Output -) Circuit example GND Specifications Compression Video compression format Audio compression format Maximum frame rate Camera Image device Synchronising Minimum illumination JPEG/MPEG4/H.264 G.711/G.726 (40,32,24,16 kbps) 30 fps SNC-EP580/ER580: 1/2.8 type Exmor CMOS SNC-EP550/ER550: 1/4 type Exmor CMOS SNC-EP521/EP520/ER521/ER520: 1/4 type interline transfer CCD Internal SNC-EP580/ER580: 1.7 lx (Shutter speed: 1/30 sec, Exposure: Full auto, 50IRE [IP]) SNC-EP550/ER550: 1.0 lx (Shutter speed: 1/60 sec, Exposure: Full auto, 50IRE [IP]) SNC- EP521/ER521: 1.4 lx (Shutter speed: 1/50 sec, Exposure: Full auto, 50IRE [IP]) SNC- EP520/ER520: 1.4 lx (Shutter speed: 1/60 sec, Exposure: Full auto, 50IRE [IP]) Video S/N 50 dB (Gain 0 dB) Lens Focus length Maximum relative aperture Minimum object distance SNC-EP580/ER580: f=4.7 to 94.0 mm SNC-EP550/ER550: f=3.5 to 98.0 mm SNC-EP521/EP520/ER521/ER520: f=3.4 to 122.4 mm SNC-EP580/ER580: F1.6 to F3.5 SNC-EP550/ER550: F1.35 to F3.7 SNC-EP521/EP520/ER521/ER520: F1.6 to F4.5 320 mm Mechanism Pan Tilt Interface Network port I/O port SD memory card slot Microphone input Line output SNC-EP580/EP550/EP521/EP520: 340° SNC-ER580/ER550/ER521/ER520: 360°, endless rotation Maximum speed: 300°/s SNC-EP580/EP550/EP521/EP520: 105° SNC-ER580/ER550/ER521/ER520: 210° (with auto invert function) Maximum speed: 300°/s 10BASE-T/100BASE-TX, auto negotiation (RJ-45) Sensor input: × 2, make contact Alarm output: × 1, 24 V AC/DC, 1 A (mechanical relay outputs electrically isolated from the camera) Minijack (monaural) Plug-in-power supported (rated voltage: 2.5 V DC) Recommended load impedance 2.2 kohms Minijack (monaural), Maximum output level: 1 Vrms Others Power supply 24 V AC ± 10%, 50 Hz/60 Hz IEEE802.3at compliant (HPoE system) Power consumption Max. 25 W Operating temperature -5°C to +50°C (23°F to 122°F) (activation temperature range: 0°C to 50°C (32°F to 122°F)) Storage temperature -20°C to +60°C (-4°F to +140°F) Operating humidity 20% to 80% Storage humidity 20% to 95% Dimensions (Diameter/Height)  ø147.4 mm × 190.9 mm (ø5 7/8 inches × 7 5/8 inches) (When installing the ceiling bracket, not including the projecting parts) Mass Approx. 1.7 kg (3 lb 12 oz) (including ceiling bracket) Supplied accessories Ceiling bracket (1) Screws (2) Installation manual (1 set) CD-ROM (User's Guide, supplied programs) (1) Template (1) 24 V AC connector (1) I/O connector (1) Design and specifications are subject to change without notice. Recommendation of Periodic Inspections In case using this device over an extended period of time, please have it inspected periodically for safe use. It may appear flawless, but the components may have deteriorated over time, which may cause a malfunction or accident. For details, please consult the store of purchase or an authorized Sony dealer.