Sony SRG-A40 Remote Camera System Guide - Page 20

Precautions, From TOP MENU, select AUTO IP SETUP >SETUP IP.

Get Sony SRG-A40 PDF manuals and user guides View all Sony SRG-A40 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

0200 Chapter 2: Connection & Basic Settings:  Auto IP address setting from RM-IP500 4. After setting the IP address, subnet mask, and default gateway, change [APPLY] >[NOT EXEC] to [EXEC], then press the VALUE button. The RM-IP500 connection mode is set to IP connection. 5. After confirming that the camera is turned on, press the RM MENU button. 6. From TOP MENU, select AUTO IP SETUP >SETUP IP. The following screen appears. 7. After specifying the range of IP addresses assigned to the camera, change [SETUP IP] >[NOT EXEC] to [EXEC], then press the VALUE button. 8. Change [CONFIRM: NO] displayed on the screen to [YES], then press the VALUE button. After completing IP address settings, "COMPLETE DONE" is displayed on the screen. The RM-IP500 camera selection block CAMERA button assigned by the camera is lit blue. 9. Press the CANCEL button to return to the TOP MENU and confirm that the selected camera can be controlled. The set IP address can be checked in AUTO IP SETUP >CAMERA TABLE. Precautions ˎˎBRBK-IP10 control card (sold separately) is required to control BRC-H900 via IP. ˎˎAt factory default settings, the IP address of RM-IP500 is 192.168.0.10, and the IP address of the IP control card is 192.168.0.100. If you do not know the IP address of the camera or IP control card, press the network reset switch on the back of each device to reset network settings. ˎˎSee the RM-IP500 operation manual for other advanced settings.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
000
Chapter 2: Connection & Basic Settings:
 Auto IP address setting from RM-IP500
20
4.
After setting the IP address, subnet mask, and default gateway, change [APPLY] >[NOT EXEC] to
[EXEC], then press the VALUE button.
The RM-IP500 connection mode is set to IP connection.
5.
After confirming that the camera is turned on, press the RM MENU button.
6.
From TOP MENU, select AUTO IP SETUP >SETUP IP.
The following screen appears.
7.
After specifying the range of IP addresses assigned to the camera, change [SETUP IP] >[NOT EXEC]
to [EXEC], then press the VALUE button.
8.
Change [CONFIRM: NO] displayed on the screen to [YES], then press the VALUE button.
After completing IP address settings, “COMPLETE DONE” is displayed on the screen.
The RM-IP500 camera selection block CAMERA button assigned by the camera is lit blue.
9.
Press the CANCEL button to return to the TOP MENU and confirm that the selected camera can be
controlled.
The set IP address can be checked in AUTO IP SETUP >CAMERA TABLE.
Precautions
ˎ
BRBK-IP10 control card (sold separately) is required to control BRC-H900 via IP.
ˎ
At factory default settings, the IP address of RM-IP500 is 192.168.0.10, and the IP address of the IP
control card is 192.168.0.100. If you do not know the IP address of the camera or IP control card, press
the network reset switch on the back of each device to reset network settings.
ˎ
See the RM-IP500 operation manual for other advanced settings.