Sony SRS-ZP1000 Operating Instructions - Page 1
Sony SRS-ZP1000 Manual
View all Sony SRS-ZP1000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
2-318-426-12(1) Active Speaker System Operating Instructions Manual de instrucciones SRS-ZP1000 2005 Sony Corporation Printed in Malaysia Owner's Record The model number and the serial number are located on the rear of the left speaker. Record the model number and the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. SRS-ZP1000 Serial No. A Right speaker (rear) Left speaker (rear) Rch IN Be sure to match the + (red) and - (black) wires and connectors for the left and right speakers. Rch OUT B Right speaker (rear) Left speaker (rear) To LINE OUT or to headphones jack (stereo mini jack) to INPUT2 jack CD/MD Walkman*, etc Connecting cord (not supplied) CD/MD player, etc. to wall outlet to INPUT1 jack To LINE OUT or to headphones jack (stereo mini jack) Connecting cord (supplied) PC, etc. About the INPUT 1 and INPUT 2 jacks Connect to a CD/MD Walkman* and PC etc., with a headphones jack or LINE OUT jack. When the component has both a headphones jack and a LINE OUT jack, connect to the LINE OUT jack of this system. If you connect to the headphones jack of this system, turn down the connected component volume level to prevent audio distortion. * "WALKMAN" is a registered trademark of Sony Corporation to represent Headphone Stereo products. C Left speaker (front) PC, CD or MD Walkman, etc. Right speaker (front) D Left speaker (front) MOVIE MUSIC MIN MAX MIN MAX POWER SOUND MODE BASS VOLUME PHONES POWER SOUND MODE BASS VOLUME PHONES English Before operating the unit, please read this manual thoroughly and retain it for future reference. WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. To prevent fire, do not Cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. Do not place lighted candles on the apparatus. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the apparatus. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. CAUTION You are cautioned that any changes or modification not expressly approved in this manual could void your authority to operate this equipment. NOTICE FOR THE CUSTOMERS IN THE USA This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Precautions On safety The nameplate indicating operating voltage, power consumption, etc., is located on the rear exterior. • Before operating the system, be sure that the operating voltage of the system is identical with that of your local power supply. Where purchased U.S.A./Canada European countries Other countries Operating voltage 120 V AC, 60 Hz 220 - 230 V AC, 50 Hz • 110 - 120 V AC, 50/60 Hz • 220 - 230 V AC, 50 Hz • The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. • Unplug the system from the wall outlet if it is not to be used for an extended period of time. To disconnect the cord, pull the cord by grasping the plug. Never pull the cord itself. • Should any liquid or solid object fall into the system, unplug the system's power cord and have the system checked by qualified personnel before operating it any further. • The AC power cord should be changed only at a qualified service shop. • For efficient heat dissipation, ensure there is sufficient space to the rear of the left speaker. Also, avoid placing objects on the unit. • Do not insert your hand or any objects into the hole of speaker. On operation • Do not drive the speaker system with a continuous wattage exceeding the maximum input power of the system. • Before connecting, turn off the Speaker system, the PC and the audio component to avoid damaging the speaker system. • The volume level should not be turned up to the point of distortion. • Although this system is magnetically shielded, do not leave recorded tapes, watches, personal credit cards or floppy disks using magnetic coding in front of the system for an extended period of time. If the TV picture or monitor display is magnetically distorted Although this system is magnetically shielded, there may be cases that the picture on some TV sets/personal computers may become magnetically distorted. In such a case, turn off the power of the TV set/personal computer once, and after 15 to 30 minutes turn it on again. In the case of a personal computer, take appropriate measures, such as data storage, before turning it off. When there seems to be no improvement, locate the system farther away from the TV set/personal computer. Furthermore, be sure not to place objects in which magnets are attached or used near the TV set/personal computer, such as audio racks, TV stands, toys etc. These may cause magnetic distortion to the picture due to their interaction with the system. On placement • Do not set the speakers in an inclined position. • Do not leave the system in a location near heat sources, or in a place subject to direct sunlight, excessive dust, moisture, rain or mechanical shock. On cleaning Do not use alcohol, benzine, or thinner to clean the cabinet. If you have any questions or problems concerning your speaker system, please consult your nearest Sony dealer. Hooking up the system 1 Connect the left speaker to the right speaker with the supplied cable. (see fig. A) Be sure to match the + (red) and - (black) wires and connectors for the left and right speakers. Note Do not connect any other speakers to this system. A malfunction of this system or the connected component may result. The sound will not be produced if you miss-connect the + and - wires and connectors. 2 Connect the left speaker to the source equipment. (see fig. B) When the system is connected to the monaural jack of a radio, etc., the sound may only come through the left speaker. In such a case, use the optional Sony plug adaptor PC-251MS. The sound will come through both speakers. To connect to a stereo phone-type headphones jack Use the optional PC-234HS plug adaptor or RK-G22 connecting cord. Note To switch INPUT1 and INPUT2, use ON/OFF of the device connected to the speakers. 3 Connect the left speaker to the wall outlet. 4 Position the speakers. (see fig. C) Listening to the sound (see fig. D) First, turn down the volume on the left speaker. The volume should be set to minimum before you begin playing the programme source. 1 Press POWER on the left speaker. The POWER indicator lights up. 2 Adjust the VOLUME control. When connecting to the headphone output, also adjust the volume of the connected component. After listening, press the POWER switch (4 OFF). The POWER indicator goes off. To adjust the bass volume level Turn the BASS dial on the left speaker to adjust the bass volume. Set the bass volume to an undistorted level to prevent system damage. On the sound mode You can enjoy the best performance of the source by using the SOUND MODE dial. - MOVIE: enjoy movies or games on the PC with full bass tones and clear high tones. - MUSIC: enjoy music with clear fidelity. The system can recognize strong sounds and change the frequency for each sound mode. You can get the best bass frequency for each sound mode by turning the BASS dial. Sound pressure MUSIC MOVIE BASS control image Frequency 3 Using headphones/earphones Connect headphones/earphones to the PHONES jack. Note Turn off the MEGA BASS or BASS BOOST (Walkman, etc.) function as it may cause audible distortion. Troubleshooting Should you encounter a problem with your speaker system, check the following list and take the indicated measures. If the problem persists, consult your nearest Sony dealer. There is no sound from the speaker system. • Make sure all the connections have been correctly made. • Make sure the volume on the left speaker and the connected component have been turned up properly. • Check if headphones are connected. If they are, disconnect them. The sound is distorted. • Turn down the volume level on the connected component. Or, if the connected component has the bass boost function, set it to off. • Rotate VOLUME on this unit to reduce the volume. There is hum or noise in the speaker output. • Make sure all the connections have been correctly made. • Make sure none of the audio components are positioned too close to the TV set. The sound has suddenly stopped. Make sure all the connections have been correctly made. The brightness of the POWER indicator is unstable. The brightness of the POWER indicator may become unstable when the volume is turned up. This is not malfunction. Specifications Speaker section Speaker system Speaker units Enclosure type Impedance 2 way 10 cm, cone type 2.5 cm, cone type Bass reflex 4 Ω Amplifier section Rated output Input impedance Input 25 W + 25 W (10 % T.H.D., 1 kHz, 4 Ω) 4.7 kΩ (at 1kHz) Stereo mini jack × 2 (INPUT 1, INPUT 2) General Dimensions (w/h/d) Mass Cord length Power consumptions Cord length Approx. 140 × 330 × 203 mm (5 5⁄8 × 13 × 8 in.) Approx. 4,500 g (9 lb. 15 oz.) (L ch), approx. 2,800 g (6 lb. 3 oz.) (R ch) Approx. 1.5 m (L to R) 21 W Approx. 2 m (power cord) Optional accessories Connecting cord RK-G22 Plug adaptor PC-234HS, PC-251MS Design and specifications are subject to change without notice.