Home » Sony Manuals » Home Theater Systems » Sony STR DA5400ES » Manual Viewer

Sony STR DA5400ES Operating Instructions - Page 151

Control for HDMI, Audio Control function.

UPC - 027242732117

Add to My Manuals
Save this manual to your list of manuals

Page 151 highlights

• Make sure you set the tuning interval correctly (when tuning in AM stations with direct tuning). • No stations have been preset or the preset stations have been cleared (when tuning by scanning preset stations). Preset the stations (page 68). • Press DISPLAY so that the frequency appears on the display. The system cannot receive satellite channels at all. (U.S.A./Canadian model only) • The receiving condition is not good. Move the antenna to the place where the condition is good. • Check that you subscribed to the desired satellite radio service (see page 69). RDS does not work. (European model only) • Make sure that you are tuned to an FM RDS station. • Select a stronger FM station. The RDS information that you want does not appear. (European model only) • Contact the radio station and find out whether or not they actually provide the service in question. If so, the service may be temporarily out of order. Control for HDMI The Control for HDMI function does not work. • Check the HDMI connection (page 35). • Make sure "Control for HDMI" is set to "ON" in HDMI settings menu. • Make sure the connected component is compatible with the Control for HDMI function. • Check the Control for HDMI settings on the connected component. See the operating instructions of the connected component. • If you change the HDMI connection, connect/disconnect the AC power cord, or there is a power failure, repeat the procedures of "Preparing for the "BRAVIA" Sync" (page 98). • If you select HDMI B using the HDMI OUTPUT button, after you have selected HDMI A, the Control for HDMI function may not work properly for a while. This is because the component connected to the HDMI A jack must re-recognize the receiver that is equipped with the Control for HDMI function. If the Control for HDMI function does not work properly for a long time, perform the steps given in "Preparing for the "BRAVIA" Sync" (page 98). • When HDMI B is selected, the Control for HDMI function does not work. No sound is output from the receiver and TV speaker while using the System Audio Control function. • Make sure the TV is compatible with the System Audio Control function. • If the TV does not have System Audio Control function, set the "Audio Out" settings in HDMI settings menu to - "TV+AMP" if you want to listen to the sound from the TV speaker and receiver. - "AMP" if you want to listen to the sound from the receiver. • You cannot listen to the sound of a component connected to the receiver while a TV is selected as the input on the receiver. - Change the input of the receiver to HDMI when you want to watch a program on a component connected to the receiver. - Change the TV channel when you want to watch a TV broadcast. - Select the component or input you want to watch when you watch a program on the component connected to the TV. Refer to the operating instructions of the TV on this operation. continued 151GB Additional Information

Section	Page
GB	2
Table of Contents	6
Getting Started	23
1: Installing speakers	23
2: Connecting speakers	25
3: Connecting the monitor	27
4a: Connecting the audio components	29
4b: Connecting the video components	34
5: Connecting the antennas (aerials)	43
6: Preparing the receiver and the remote	44
7: Displaying the GUI menu on the TV screen	45
8: Setting the speakers	46
9: Calibrating the appropriate speaker settings automatically (Auto Calibration)	48
Guide to on-screen display operation	55
Playback	58
Enjoying sound/images from the component connected to the receiver	58
Enjoying sound/images from the components connected to the DIGITAL MEDIA PORT	60
Operating the TDM-iP1/ iP50/TDM-NC1 using the GUI menu of the receiver	61
Tuning	65
Listening to FM/AM radio	65
Presetting FM/AM radio stations	68
Listening to satellite radio (U.S.A./Canadian model only)	69
Connecting a satellite radio tuner	71
Preparing to listen to a satellite radio	71
Selecting a channel of the satellite radio	73
Presetting satellite radio channels	74
Restricting access to specific channels (Parental Lock) (SIRIUS only)	75
Enjoying Surround Sound	79
Playing back with 2-channel sound	79
Playing back with multi-channel surround	80
Enjoying a surround effect for music	83
Enjoying a surround effect for movies	85
Using Multi-zone Features	89
What you can do with the Multi-zone function	89
Making a multi-zone connection	90
Setting the speakers in zone 2	94
Switching the zone setting of the remote	95
Operating the receiver from another zone (ZONE 2/ZONE 3 operations)	96
Using Other Features	98
Using “BRAVIA” Sync features	98
Switching the monitors that output the HDMI video signals	101
Switching between digital and analog audio	102
Enjoying the sound/ images from other inputs (Input Assign)	103
Using the sleep timer	105
Enjoying the surround effect at low volume levels	106
Recording using the receiver	107
Switching the command mode of the receiver and the remote	108
Using a bi-amplifier connection	110
Adjusting Settings	111
Using the setting menu	111
Auto Calibration	112
Speaker settings	114
Surround settings	118
EQ settings	119
Multi Zone settings	120
Audio settings	121
Video settings	122
HDMI settings	125
System settings	126
Operating without connecting to a TV	127
Using the Remote	132
Operating each component using the remote	132
Programming the remote	135
Performing several commands in sequence automatically (Macro Play)	139
Setting remote commander codes that are not stored in the remote	141
Clearing all the contents of the remote’s memory	142
Additional Information	143
Glossary	143
Precautions	146
Troubleshooting	147
Specifications	153
Index	155
FR	158
Table des matières	161
Mise en service	181
1: Installation des enceintes	181
2: Raccordement des enceintes	183
3: Raccordement de l’écran	185
4a: Raccordement des appareils audio	187
4b: Raccordement des appareils vidéo	192
5: Raccordement des antennes	201
6: Préparation de l’ampli- tuner et de la télécommande	202
7: Affichage du menu GUI sur l’écran du téléviseur	204
8: Réglage des enceintes	205
9: Calibrage automatique aux réglages appropriés (Auto Calibration)	207
Guide pour les opérations à l’écran	214
Lecture	217
Écoute du son/visionnage d’images à partir de l’appareil raccordé à l’ampli-tuner	217
Écoute du son/visionnage d’images à partir des appareils raccordés au DIGITAL MEDIA PORT	219
Commande du TDM-iP1/ iP50/TDM-NC1 à l’aide du menu GUI de l’ampli- tuner	221
Sélection des stations	224
Écoute de stations de radio FM/AM	224
Préréglage des stations de radio FM/AM	227
Écoute de la radio satellite (Modèle américain/canadien uniquement)	229
Raccorder un tuner radio satellite	230
Préparer la réception de la radio satellite	231
Sélectionner un canal de la radio satellite	232
Prérégler les canaux de la radio satellite	234
Restreindre l’accès à des canaux spécifiques (Parental Lock) (SIRIUS uniquement)	235
Écoute du son surround	240
Lecture avec un son 2 canaux	240
Lecture avec son surround multicanal	241
Écoute d’un effet surround pour de la musique	244
Écoute d’un effet surround pour des films	246
Utilisation des fonctionnalités multizone	250
Ce que vous pouvez faire avec la fonction multizone	250
Effectuer un raccordement multizone	251
Réglage des enceintes dans la zone 2	255
Changer le réglage de la zone de la télécommande	256
Commande de l’ampli- tuner depuis une autre zone (Commandes ZONE 2/ZONE 3)	257
Utilisation des autres fonctionnalités	259
Utilisation des fonctionnalités « BRAVIA » Sync	259
Changement des écrans qui émettent les signaux vidéo HDMI	262
Passage entre son numérique et analogique	263
Écoute du son/visionnage d’images d’autres entrées (Input Assign)	264
Utilisation de la minuterie d’arrêt	266
Écoute du son surround à faible volume	267
Enregistrement à l’aide de l’ampli-tuner	268
Changement du mode de commande de l’ampli- tuner et de la télécommande	269
Utilisation d’un raccordement bi- amplificateur	271
Réglage des paramètres	272
Utilisation du menu de paramétrage	272
Auto Calibration	273
Paramètres Speaker	275
Paramètres Surround	279
Paramètres EQ	280
Paramètres Multi Zone	281
Paramètres Audio	283
Paramètres Video	284
Paramètres HDMI	287
Paramètres System	288
Utilisation sans raccordement à un téléviseur	289
Utilisation de la télécommande	294
Commande de chaque appareil à l’aide de la télécommande	294
Programmation de la télécommande	297
Exécution automatique d’une séquence de plusieurs commandes (Exécution de macro-commandes)	301
Mémorisation de codes de télécommande n’ayant pas été préprogrammés dans la télécommande	303
Effacement de tout le contenu de la mémoire de la télécommande	304
Informations complémentaires	305
Glossaire	305
Précautions	309
Guide de dépannage	310
Spécifications	315

Match case Limit results 1 per page

151

Additional Information

• Make sure you set the tuning interval

correctly (when tuning in AM stations

with direct tuning).

• No stations have been preset or the preset

stations have been cleared (when tuning by

scanning preset stations). Preset the

stations (page 68).

• Press DISPLAY so that the frequency

appears on the display.

The system cannot receive satellite

channels at all. (U.S.A./Canadian model

only)

• The receiving condition is not good. Move

the antenna to the place where the

condition is good.

• Check that you subscribed to the desired

satellite radio service (see page 69).

RDS does not work. (European model

only)

• Make sure that you are tuned to an FM

RDS station.

• Select a stronger FM station.

The RDS information that you want

does not appear. (European model

only)

• Contact the radio station and find out

whether or not they actually provide the

service in question. If so, the service may

be temporarily out of order.

The Control for HDMI function does not

work.

• Check the HDMI connection (page 35).

• Make sure “Control for HDMI” is set to

“ON” in HDMI settings menu.

• Make sure the connected component is

compatible with the Control for HDMI

function.

• Check the Control for HDMI settings on

the connected component. See the

operating instructions of the connected

component.

• If you change the HDMI connection,

connect/disconnect the AC power cord, or

there is a power failure, repeat the

procedures of “Preparing for the

“BRAVIA” Sync” (page 98).

• If you select HDMI B using the HDMI

OUTPUT button, after you have selected

HDMI A, the Control for HDMI function

may not work properly for a while. This is

because the component connected to the

HDMI A jack must re-recognize the

receiver that is equipped with the Control

for HDMI function. If the Control for

HDMI function does not work properly for

a long time, perform the steps given in

“Preparing for the “BRAVIA” Sync”

(page 98).

•

When HDMI B is selected, the Control for

HDMI function does not work.

No sound is output from the receiver

and TV speaker while using the System

Audio Control function.

• Make sure the TV is compatible with the

System Audio Control function.

• If the TV does not have System Audio

Control function, set the “Audio Out”

settings in HDMI settings menu to

–

“TV+AMP” if you want to listen to the

sound from the TV speaker and

receiver.

–

“AMP” if you want to listen to the

sound from the receiver.

• You cannot listen to the sound of a

component connected to the receiver while

a TV is selected as the input on the

receiver.

–

Change the input of the receiver to

HDMI when you want to watch a

program on a component connected to

the receiver.

–

Change the TV channel when you want

to watch a TV broadcast.

–

Select the component or input you want

to watch when you watch a program on

the component connected to the TV.

Refer to the operating instructions of the

TV on this operation.

Control for HDMI

continued