Sony STR-K7000 Operating Instructions (HT-7000DH) - Page 78

Specifications, AUDIO POWER - troubleshooting

Get Sony STR-K7000 - Receiver PDF manuals and user guides View all Sony STR-K7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

Error messages If there is a malfunction, the display shows a message. You can check the condition of the system by the message. Refer to the following table to solve the problem. If any problem persists, consult your nearest Sony dealer. If an error message appears while you perform Auto Calibration, see "Error and warning codes" (page 32) to solve the problem. DEC. EROR Appears when a signal the receiver cannot decode (ex. DTS-CD) is input and "DEC. PRI." on the AUDIO menu is set to "DEC. PCM". Set it to "DEC. AUTO" (page 41). PROTECT Irregular current is output from the speakers. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. If you are unable to remedy the problem using the troubleshooting guide Clearing the receiver's memory may remedy the problem (page 29). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver. If the problem persist Consult your nearest Sony dealer. Note that if service personnel changes some parts during repair, these parts may be retained. Reference sections for clearing the receiver's memory To clear All memorized settings Customized sound fields See page 29 page 53 Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code U only) With 6 ohm loads, both channels driven, from 120 - 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.7% total harmonic distortion from 250 milliwatts to rated output. Amplifier section Power Output1) Models of area code U (6 ohms 1 kHz, THD 10%) FRONT2): 140 W/ch CENTER2): 140 W SUR2): 140 W/ch Models of area code CA (6 ohms 1 kHz, THD 0.7%) FRONT2): 90 W/ch CENTER2): 90 W SUR2): 90 W/ch (6 ohms 1 kHz, THD 10%) FRONT2): 140 W/ch CENTER2): 140 W SUR2): 140 W/ch 1)Measured under the following conditions: Area code Power requirements U, CA 120 V AC, 60 Hz 2)Depending on the sound field settings and the source, there may be no sound output. Inputs (Analog) MULTI CH IN, SA-CD/CD, MD/TAPE, DVD, VIDEO 1, 2, 3 Sensitivity: 800 mV Impedance: 50 kohms 78US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
78
US
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer.
If an error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 32) to solve the problem.
DEC. EROR
Appears when a signal the receiver cannot
decode (ex. DTS-CD) is input and “DEC.
PRI.” on the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 41).
PROTECT
Irregular current is output from the
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy
the problem (page 29). However, note that all
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
Reference sections for clearing
the receiver’s memory
Specifications
AUDIO POWER
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
(Models of area code U only)
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.7% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
Power Output
1)
Models of area code U
(6 ohms 1 kHz, THD 10%)
FRONT
2)
:
140 W/ch
CENTER
2)
:
140 W
SUR
2)
:
140 W/ch
Models of area code CA
(6 ohms 1 kHz, THD 0.7%)
FRONT
2)
:
90 W/ch
CENTER
2)
:
90 W
SUR
2)
:
90 W/ch
(6 ohms 1 kHz, THD 10%)
FRONT
2)
:
140 W/ch
CENTER
2)
:
140 W
SUR
2)
:
140 W/ch
1)
Measured under the following conditions:
2)
Depending on the sound field settings and the
source, there may be no sound output.
Inputs (Analog)
To clear
See
All memorized settings
page 29
Customized sound fields
page 53
Area code
Power requirements
U, CA
120 V AC, 60 Hz
MULTI CH IN,
SA-CD/CD,
MD/TAPE, DVD,
VIDEO 1, 2, 3
Sensitivity: 800 mV
Impedance: 50 kohms