Sony VPL-HW65 Operating Instructions - Page 44

Message Lists

Get Sony VPL-HW65 PDF manuals and user guides View all Sony VPL-HW65 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Message Lists Warning messages Symptom Cause and Remedy Page High temp.! Lamp off in Turn off the power. - 1 min. Check to ensure that nothing is blocking the ventilation 4, 5 holes. Frequency is out of range! Frequency is out of range. Input a signal that is within the 52 acceptable frequency range of the unit. Please replace the Lamp/ It is time to replace the lamp. Replace the lamp. 46 Filter. Also, replace the air filter too. Restart cleaning the ventilation holes (intake). If this message appears again after you replace the lamp and filter, the lamp replacement process is not complete. Check the lamp replacement process. Note To clear this message, press any button either on the remote control or the control panel of the unit once. Please clean the filter. It is time to clean the air filter. Clean the air filter. 49 Note To clear this message, press any button either on the remote control or the control panel of the unit once. Please clean the filter. It is time to clean the air filter. Clean the air filter. 49 Have you finished? Yes If you cleaned the air filter, select "Yes." If you did not clean No the air filter, select "No." Projector temperature is Check to ensure that nothing is blocking the ventilation 4, 5 high. High Altitude holes. Mode should be "On" if projector is being used at high altitude. When using the unit at high altitude, set "High Altitude Mode" to "On." 29 Note When temperature inside the unit remains high, "High Altitude Mode" is switched to "On" in 1 minute, then the fan speed increases. Power Saving Mode is "Power Saving" is set to "Standby." 29 set. Projector will automatically enter Standby Mode in 1 minute. Note If no signal is input, the power turns off after 1 minute, and the projector goes into standby mode. Caution messages Symptom x Not applicable! Settings Lock enabled. Cause and Remedy Page No signal is input in the selected input. Check connections. 12 Press the appropriate button. - The operation to be activated by the button is currently prohibited. "Settings Lock" is set to "Level A" or "Level B." 31 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
44
Message Lists
Warning messages
Caution messages
Symptom
Cause and Remedy
Page
High temp.! Lamp off in
1 min.
Turn off the power.
–
Check to ensure that nothing is blocking the ventilation
holes.
4, 5
Frequency is out of
range!
Frequency is out of range. Input a signal that is within the
acceptable frequency range of the unit.
52
Please replace the Lamp/
Filter.
It is time to replace the lamp. Replace the lamp.
Also, replace the air filter too. Restart cleaning the
ventilation holes (intake).
If this message appears again after you replace the lamp and
filter, the lamp replacement process is not complete. Check
the lamp replacement process.
To clear this message, press any button either on the remote
control or the control panel of the unit once.
46
Please clean the filter.
It is time to clean the air filter. Clean the air filter.
To clear this message, press any button either on the remote
control or the control panel of the unit once.
49
Please clean the filter.
Have you finished? Yes
No
It is time to clean the air filter. Clean the air filter.
If you cleaned the air filter, select “Yes.” If you did not clean
the air filter, select “No.”
49
Projector temperature is
high. High Altitude
Mode should be “On” if
projector is being used at
high altitude.
Check to ensure that nothing is blocking the ventilation
holes.
4, 5
When using the unit at high altitude, set “High Altitude
Mode” to “On.”
When temperature inside the unit remains high, “High
Altitude Mode” is switched to “On” in 1 minute, then the
fan speed increases.
29
Power Saving Mode is
set. Projector will
automatically enter
Standby Mode in 1
minute.
“Power Saving” is set to “Standby.”
If no signal is input, the power turns off after 1 minute, and
the projector goes into standby mode.
29
Symptom
Cause and Remedy
Page
No signal is input in the selected input. Check connections.
12
Not applicable!
Press the appropriate button.
The operation to be activated by the button is currently
prohibited.
–
Settings Lock enabled.
“Settings Lock” is set to “Level A” or “Level B.”
31
Note
Note
Note
Note
x