Sony ZS-D10 Primary User Manual - Page 1

Sony ZS-D10 - Cd Boombox Manual

Page 1 highlights

Precautions On safety • As the laser beam used in the CD player section is harmful to the eyes, do not attempt to disassemble the casing. Refer servicing to qualified personnel only. • Should any solid object or liquid fall into the player, unplug the player, and have it checked by qualified personnel before operating it any further. • Discs with non-standard shapes (e.g., heart, square, star) cannot be played on this player. Attempting to do so may damage the player. Do not use such discs. Cleaning the cabinet • Clean the cabinet, panel and controls with a soft cloth slightly moistened with a mild detergent solution. Do not use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. On power sources • For AC operation, use the supplied AC power adaptor; do not use any other type. Polarity of the plug • The player is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the player itself has been turned off. • Unplug the player from the wall outlet when it is not be used for an extended period of time. • When the batteries are not to be used, remove them to avoid damage that can be caused by battery leakage or corrosion. • The nameplate indicating operating voltage, etc. is located at the rear. On placement • Do not leave the player in a location near heat sources, or in a place subject to direct sunlight, excessive dust or mechanical shock. • Do not place the player on an inclined or unstable place. • Do not place anything within 10 mm of the side of the cabinet. The ventilation holes must be unobstructed for the player to operate properly and prolong the life of its components. • If the player is left in a car parked in the sun, be sure to choose a location in the car where the player will not be subjected to the direct rays of the sun. • Since a strong magnet is used for the speakers, keep personal credit cards using magnetic coding or spring-wound watches away from the player to prevent possible damage from the magnet. On operation • If the player is brought directly from a cold to a warm location, or is placed in a very damp room, moisture may condense on the lenses inside the CD player section. Should this occur, the player will not operate properly. In this case, remove the CD and wait about an hour for the moisture to evaporate. Notes on CDs • Before playing, clean the CD with a cleaning cloth. Wipe the CD from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners or anti-static spray intended for vinyl LPs. • Do not expose the CD to direct sunlight or heat sources such as hot air ducts, nor leave it in a car parked in direct sunlight as there can be a considerable rise in temperature inside the car. • Do not stick paper or sticker on the CD, nor scratch the surface of the CD. • After playing, store the CD in its case. If there is a scratch, dirt or fingerprints on the CD, it may cause tracking error. About CD-Rs/CD-RWs This player can play CD-Rs/CD-RWs recorded in the CD-DA format*, but playback capability may vary depending on the quality of the disc and the condition of the recording device. * CD-DA is the abbreviation for Compact Disc Digital Audio. It is a recording standard used for Audio CDs. Music discs encoded with copyright protection technologies This product is designed to play back discs that conform to the Compact Disc (CD) standard. Recently, various music discs encoded with copyright protection technologies are marketed by some record companies. Please be aware that among those discs, there are some that do note conform to the CD standard and may not by playable by this product. If you have any questions or problems concerning your player, please consult your nearest Sony dealer. Troubleshooting General The power does not come on. • Connect the AC power adaptor to a wall outlet securely. There is no audio. • Make sure the function you want to use appears in the display window. • Adjust the volume. • Unplug the headphones when listening through speakers. Noise is heard. • Someone is using a portable telephone or other equipment that emits radio waves near the player. tMove the portable telephone, etc., away from the player. CD Player The CD does not play or "no dISC" lights in the display even when a CD is in place. • Place the CD with the label surface you. • Make sure that the CD compartment is closed. • Clean the CD. • Take out the CD and leave the CD compartment open for about an hour to dry moisture condensation. • Make sure "Cd" appears in the display. • The CD-R/CD-RW was not finalized. Finalize the CD-R/CD-RW with the recording device. • There is a problem with the quality of the CDR/CD-RW, recording device, or application software. The sound drops out. Noise is heard. • Reduce the volume. • Clean the CD, or replace it if the CD is badly damaged. • Place the player in a location free from vibration. • Clean the lens with a commercially available blower. • The sound may drop out or noise may be heard when using poor quality CD-Rs/CDRWs or if there is a problem with the recording device or application software. Lens Radio Reception is poor. • Reorient the antenna to improve FM reception. • Reorient the player itself to improve AM reception. Remote The remote does not function. • Replace the battery in the remote with new one if it is weak. • Make sure that you are pointing the remote at the remote sensor on the player. • Remove any obstacles in the path of the remote and the player. • Make sure the remote sensor is not exposed to strong light such as direct sunlight or fluorescent lamp light. • Move closer to the player when using the remote. After trying the above remedies, if you still have problems, unplug the AC power adaptor. After all the indications in the display disappear, plug the AC power adaptor. If the problem persists, please consult your nearest Sony dealer. The audio is weak or has poor quality. • Move the player away from the TV. • If you are using the remote while listening to AM radio, noise may be heard. This is unavoidable. The picture of your TV becomes unstable. • If you are listening to an FM program near the TV with an indoor antenna, move the player away from the TV. Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION With 6-ohm loads, both channels driven from 1 000 - 10 000 Hz; rated 3.5 W per channel-minimum RMS power, with no more than 10 % total harmonic distortion in AC operation. Other specifications CD player section System Compact disc digital audio system Laser diode properties Material: GaAlAs Wave length: 780 nm Emission duration: Continuous Laser output: Less than 44.6 µW (This output is the value measured at a distance of about 200 mm from the objective lens surface on the optical pick-up block with 7 mm aperture.) Spindle speed 200 r/min (rpm) to 500 r/min (rpm) (CLV) Number of channels 2 Frequency response 20 - 20 000 Hz +1/-2 dB Wow and flutter Below measurable limit Radio section Frequency range FM: 87.5 - 108 MHz AM: 531 - 1 611 kHz (Taiwan model) 530 - 1 710 kHz (Other models) Antennas FM: Telescopic antenna AM: Built-in ferrite bar antenna General Speaker Full range: 8 cm (3 1⁄4 in.) dia., 6 Ω, cone type (2) Input LINE IN jack (stereo minijack): Minimum input level 330 mV Outputs Headphones jack (stereo minijack): For 16 - 68 Ω impedance headphones OPTICAL DIGITAL OUT (CD) (optical output connector): Wavelength 630 - 690 nm Power output 4 W + 4 W (at 6 Ω, 10% harmonic distortion) Power requirements For Personal Audio System: DC IN 10V jack accepts: Supplied AC power adaptor for use with: 120V AC, 60 Hz For remote control: 3 V DC, 2 size AAA (R03) batteries Dimensions Approx. 530 × 195 × 127 mm (w/h/d) (20 7⁄8 × 7 3⁄4 × 5 inches) (incl. projecting parts) Mass Approx. 2.5 kg (5 lb. 8 oz) Supplied accessory AC power adaptor (1) Remote control (1) Design and specifications are subject to change without notice. Optional accessories Sony MDR headphone series Personal Audio System Operating Instructions ZS-D10 ©2003 Sony Corporation Printed in China 3-251-193-91 (1) English WARNING To prevent fire or shock hazard, do not expose the player to rain or moisture. This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION The use of optical instruments with this product will increase eye hazard. WARNING Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. To prevent fire or shock hazard, do not place objects filled with liquids, such as vases, on the appliance. For customers in Canada To prevent electric shock, match wide blade of plug to wide slot, fully insert. Information For customers in the USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/ TV technician for help. This class B digital device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. Replace the AC power adaptor with model ACCD10 only, if replacement is necessary. Owner's Record The model number and serial number are located at the rear. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. ZS-D10 Serial No. For customers in the USA Please register this product on line at http:// www.sony.com/productregistration. Proper registration will enable us to send you periodic mailings about new product, services and other important announcements. Registering your product will also allow us to contact you in the unlikely event that the product needs adjustment or modification. Thank you. Power Sources A B 1 to DC IN 10V 2 to a wall outlet Connect the AC power adaptor A. Preparing the remote B Insert two size AAA (R03) batteries (not supplied). Replacing batteries With normal use, the batteries should last for about six months. When the remote no longer operates the player, replace two batteries with new ones.

  • 1
  • 2

©2003 Sony Corporation
Printed in China
Operating Instructions
Personal
Audio
System
3-251-193-
91
(1)
ZS-D10
Precautions
On safety
As the laser beam used in the CD player
section is harmful to the eyes, do not
attempt to disassemble the casing. Refer
servicing to qualified personnel only.
Should any solid object or liquid fall into
the player, unplug the player, and have it
checked by qualified personnel before
operating it any further.
Discs with non-standard shapes (e.g.,
heart, square, star) cannot be played on
this player. Attempting to do so may
damage the player. Do not use such discs.
Cleaning the cabinet
Clean the cabinet, panel and controls with
a soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent,
such as alcohol or benzine.
On power sources
For AC operation, use the supplied AC
power adaptor; do not use any other type.
Polarity of the plug
The player is not disconnected from the
AC power source (mains) as long as it is
connected to the wall outlet, even if the
player itself has been turned off.
Unplug the player from the wall outlet
when it is not be used for an extended
period of time.
When the batteries are not to be used,
remove them to avoid damage that can be
caused by battery leakage or corrosion.
The nameplate indicating operating
voltage, etc. is located at the rear.
On placement
Do not leave the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust or mechanical
shock.
Do not place the player on an inclined or
unstable place.
Do not place anything within 10 mm of
the side of the cabinet. The ventilation
holes must be unobstructed for the player
to operate properly and prolong the life of
its components.
If the player is left in a car parked in the
sun, be sure to choose a location in the car
where the player will not be subjected to
the direct rays of the sun.
Since a strong magnet is used for the
speakers, keep personal credit cards using
magnetic coding or spring-wound watches
away from the player to prevent possible
damage from the magnet.
On operation
If the player is brought directly from a
cold to a warm location, or is placed in a
very damp room, moisture may condense
on the lenses inside the CD player section.
Should this occur, the player will not
operate properly. In this case, remove the
CD and wait about an hour for the
moisture to evaporate.
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION
With 6-ohm loads, both channels driven
from 1 000 - 10 000 Hz; rated 3.5 W per
channel-minimum RMS power, with no
more than 10 % total harmonic distortion
in AC operation.
Other specifications
CD player section
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wave length: 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 μW
(This output is the value measured at a distance
of about 200 mm from the objective lens surface
on the optical pick-up block with 7 mm
aperture.)
Spindle speed
200 r/min (rpm) to 500 r/min (rpm)
(CLV)
Number of channels
2
Frequency response
20 - 20 000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
Radio section
Frequency range
FM: 87.5 - 108 MHz
AM: 531 - 1 611 kHz (Taiwan model)
530 - 1 710 kHz (Other models)
Antennas
FM: Telescopic antenna
AM: Built-in ferrite bar antenna
General
Speaker
Full range: 8 cm (3
1
±
4
in.) dia., 6
, cone type
(2)
Input
LINE IN jack (stereo minijack):
Minimum input level 330 mV
Outputs
Headphones jack (stereo minijack):
For 16 - 68
impedance headphones
OPTICAL DIGITAL OUT (CD) (optical output
connector):
Wavelength 630 - 690 nm
Power output
4 W + 4 W
(at 6
, 10% harmonic
distortion)
Power requirements
For Personal Audio System:
DC IN 10V jack accepts: Supplied AC power
adaptor for use with: 120V AC, 60 Hz
For remote control:
3 V DC, 2 size AAA (R03) batteries
Dimensions
Approx. 530
×
195
×
127 mm
(w/h/d)
(20
7
±
8
×
7
3
±
4
×
5 inches)
(incl. projecting parts)
Mass
Approx. 2.5 kg (5 lb. 8 oz)
Supplied accessory
AC power adaptor (1)
Remote control (1)
Design and specifications are subject to change
without notice.
Optional accessories
Sony MDR headphone series
Troubleshooting
General
The power does not come on.
Connect the AC power adaptor to a wall outlet
securely.
There is no audio.
Make sure the function you want to use
appears in the display window.
Adjust the volume.
Unplug the headphones when listening
through speakers.
Noise is heard.
Someone is using a portable telephone or
other equipment that emits radio waves near
the player.
t
Move the portable telephone,
etc., away from the player.
CD Player
The CD does not play or “no dISC”
lights in the display even when a CD
is in place.
Place the CD with the label surface you.
Make sure that the CD compartment is closed.
Clean the CD.
Take out the CD and leave the CD
compartment open for about an hour to dry
moisture condensation.
Make sure “Cd” appears in the display.
The CD-R/CD-RW was not finalized. Finalize
the CD-R/CD-RW with the recording device.
There is a problem with the quality of the CD-
R/CD-RW, recording device, or application
software.
The sound drops out.
Noise is heard.
Reduce the volume.
Clean the CD, or replace it if the CD is badly
damaged.
Place the player in a location free from
vibration.
Clean the lens with a commercially available
blower.
The sound may drop out or noise may be
heard when using poor quality CD-Rs/CD-
RWs or if there is a problem with the
recording device or application software.
Radio
Reception is poor.
Reorient the antenna to improve FM
reception.
Reorient the player itself to improve AM
reception.
The audio is weak or has poor quality.
Move the player away from the TV.
If you are using the remote while listening to
AM radio, noise may be heard. This is
unavoidable.
The picture of your TV becomes
unstable.
If you are listening to an FM program near the
TV with an indoor antenna, move the player
away from the TV.
Notes on CDs
Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out.
Do not use solvents such as benzine,
thinner, commercially available cleaners
or anti-static spray intended for vinyl LPs.
Do not expose the CD to direct sunlight or
heat sources such as hot air ducts, nor
leave it in a car parked in direct sunlight as
there can be a considerable rise in
temperature inside the car.
Do not stick paper or sticker on the CD,
nor scratch the surface of the CD.
After playing, store the CD in its case.
If there is a scratch, dirt or fingerprints on the
CD, it may cause tracking error.
About CD-Rs/CD-RWs
This player can play CD-Rs/CD-RWs
recorded in the CD-DA format*, but
playback capability may vary depending on
the quality of the disc and the condition of
the recording device.
*
CD-DA is the abbreviation for Compact
Disc Digital Audio. It is a recording
standard used for Audio CDs.
Music discs encoded with copyright
protection technologies
This product is designed to play back discs
that conform to the Compact Disc (CD)
standard. Recently, various music discs
encoded with copyright protection
technologies are marketed by some record
companies. Please be aware that among
those discs, there are some that do note
conform to the CD standard and may not by
playable by this product.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
Remote
The remote does not function.
Replace the battery in the remote with new
one if it is weak.
Make sure that you are pointing the remote at
the remote sensor on the player.
Remove any obstacles in the path of the
remote and the player.
Make sure the remote sensor is not exposed to
strong light such as direct sunlight or
fluorescent lamp light.
Move closer to the player when using the
remote.
After trying the above remedies, if you still have
problems, unplug the AC power adaptor. After
all the indications in the display disappear, plug
the AC power adaptor. If the problem persists,
please consult your nearest Sony dealer.
Lens
Connect the AC power adaptor
A
.
Preparing the remote
B
Insert two size AAA (R03) batteries (not supplied).
Replacing batteries
With normal use, the batteries should last for about six months. When the remote no longer
operates the player, replace two batteries with new ones.
Power Sources
1
to DC IN 10V
2
to a wall outlet
A
B
English
WARNING
To prevent fire or shock hazard, do
not expose the player to rain or
moisture.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product's enclosure that may be of
sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
WARNING
Do not install the appliance in a confined space,
such as a bookcase or built-in cabinet.
To prevent fire or shock hazard, do not place
objects filled with liquids, such as vases, on the
appliance.
For customers in Canada
To prevent electric shock, match wide blade of
plug to wide slot, fully insert.
Information
For customers in the USA
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio frequency
energy and, if not installed and used in
accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the
equipment and receiver.
— Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/
TV technician for help.
This class B digital device complies with part 15
of the FCC rules. Operation is subject to the
following two conditions: (1) This device may
not cause harmful interference, and (2) this
device must accept any interference received,
including interference that may cause undesired
operation.
You are cautioned that any changes or
modifications not expressly approved in this
manual could void your authority to operate this
equipment.
Replace the AC power adaptor with model AC-
CD10 only, if replacement is necessary.
Owner's Record
The model number and serial number are located
at the rear.
Record the serial number in the space provided
below. Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No. ZS-D10
Serial No.
For customers in the USA
Please register this product on line at
http://
www.sony.com/productregistration
.
Proper registration will enable us to send you
periodic mailings about new product,
services and other important announcements.
Registering your product will also allow us to
contact you in the unlikely event that the
product needs adjustment or modification.
Thank you.