Sony ZS-Y3PSBLK Operating Instructions - Page 2
Location of controls
View all Sony ZS-Y3PSBLK manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Location of controls OPR/BATT indicator Remote sensor POWER SLEEP . PRESET - u* CD > PRESET + x RADIO BAND AUTO PRESET SOUND VOLUME +*, - MEGA BASS i Remote Control POWER FUNCTION u x MODE DSPL/ENT/MEM CD LID OPEN OPEN PUSH CLOSE Loading a CD With the labeled side up TUNE -, + Display *The button has a tactile dot. BAND PRESET +, - .,> VOL +*, - Display D Total track number Total playing time Note Make sure that the CD is placed properly on the CD tray. Don't place it under the CD tray. E Programed track Playing order To turn on/off the power Press POWER. To adjust the volume Press VOLUME +, - (VOL +, - on the remote). To listen through headphones Connect the headphones to the i (headphones) jack. Selecting the audio emphasis (SOUND/MEGA BASS) You can adjust the audio emphasis of the sound you are listening to. To select the sound characteristic Press SOUND repeatedly to select the audio emphasis you want. Choose To get powerful, clean sounds, emphasizing low and high range audio light, bright sounds emphasizing high and middle range audio percussive sounds, emphasizing bass audio the presence of vocals, stressing middle range audio the whole dynamic range for music such as classical music Playing a CD 1 Press OPEN to load a CD in the CD compartment (direct power-on). 2 Press PUSH CLOSE to close the CD compartment. 3 Press u. The player plays all the tracks once. To stop playback Press x pause playback u Press the button again to resume play after pause. go to the next track > go back to the previous track . remove the CD OPEN locate a point while listening to the sound > (forward) or . (backward) while playing until you find the point locate a point while observing the display > (forward) or . (backward) in pause until you find the point Using the display To check the total track number and playing time Press DSPL/ENT/MEM in stop mode (see fig. D). To check the remaining time Press DSPL/ENT/MEM repeatedly while playing a CD. The display changes as follows: t the current track number and playing time r the current track number and the remaining time on the current track r the number of tracks left and remaining time on the CD Selecting the play mode Press MODE until "REP 1" "REP ALL" "SHUF" "SHUF REP" "PGM" "PGM REP" appears in the display. Then proceed as follows: To repeat a single track repeat all tracks shuffle play repeat tracks in random order program play Select "REP 1" "REP ALL" "SHUF" "SHUF REP" "PGM" repeat programed tracks "PGM REP" Then do this Press . or > to select the track that you want to repeat, then press u. Press u. Press u. Press u. Press . or > then press DSPL/ENT/ MEM for the tracks you want to program in the order you want up to 20 tracks (see fig. E). Then press u. Press . or > then press DSPL/ENT/ MEM for the tracks you want to program in the order you want up to 20 tracks. Then Press u. To cancel selected play mode Press MODE until the selected mode disappears from the display. To check the programed track and playing order in the display To check the order of tracks before play, press DSPL/ENT/MEM. Every time you press the button, the track number appears in the programed order. To change the current program Press x once if the CD is stopped and twice if the CD is playing. The current program will be erased. Then create a new program following the programing procedure. Tip You can play the same program again, since the program is saved until you open the CD compartment. Listening to the radio 1 Press RADIO•BAND•AUTO PRESET until the band you want appears in the display (direct power-on). Each time you press the button, the indication changes as follows: "FM" t "AM" 2 Hold down TUNE + or - until the frequency digits begin to change in the display. The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. Tip If the FM broadcast is noisy, press MODE until "Mono" appears in the display and the radio will play in monaural. Presetting radio stations You can store radio stations into the player's memory. You can preset up to 30 radio stations, 20 for FM and 10 for AM in any order. 1 Press RADIO•BAND•AUTO PRESET to select the band. 2 Hold down RADIO•BAND•AUTO PRESET for 2 seconds until "AUTO" flashes in the display. 3 Press DSPL/ENT/MEM. The stations are stored in memory from the lower frequencies to the higher ones. If a station cannot be preset automatically You need to preset a station with a weak signal manually. 1 Press RADIO•BAND•AUTO PRESET to select the band. 2 Tune in a station you want. 3 Hold down DSPL/ENT/MEM for 2 seconds until the preset number flashes in the display. 4 Press PRESET + or - until the preset number you want for the station flashes in the display. 5 Press DSPL/ENT/MEM. The new station replaces the old one. Tip The preset radio stations remain in memory even if you unplug the mains lead or remove all the batteries. Playing preset radio stations 1 Press RADIO•BAND•AUTO PRESET to select the band. 2 Press PRESET + or - to tune in the stored station. Falling asleep to music 1 Play the music source you want. 2 Press SLEEP. 3 Press SLEEP to select the minutes until the player goes off automatically. Each time you press the button, the indication changes as follows: "60" t "90" t "120" t "OFF" t "10" t "20" t "30". To cancel the sleep function Press POWER to turn off the power. Note The backlight in the display does not light while the sleeping timer is on. To reinforce the bass sound Press MEGA BASS. "MEGA BASS" appears in the display. To return to normal sound, press the button again.