Stihl FC 75 Instruction Manual - Page 14

Using the Edger, Preparations - edger carburetor

Get Stihl FC 75 PDF manuals and user guides View all Stihl FC 75 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

English / USA Using the Edger !Warning! A worn or damaged muffler is a fire hazard and may cause loss of hearing. Check to see that the muffler is in good condition. The edger must not be operated if the muffler is not functioning properly or has been removed. Remember that the risk of forest fires is greater in hot weather. Use the spark arresting muffler supplied with the unit. Never touch a hot muffler or burn will result. !Warning! In order to reduce the risk of fire, do not modify or remove any part of the muffler or spark arrestor. Tighten all nuts, bolts and screws except the carburetor adjustment screws after each use. Keep spark plug and wire connection tight and clean. The spark plug electrode gap should be checked with a feeler gauge at least every 50 operating hours and reset if necessary. Fit a new spark plug if the electrodes are badly pitted. Additionally, the daily maintenance schedule for your edger set forth in your STIHL Owner's Manual should be strictly followed. For any maintenance please refer to the maintenance chart and to the warranty statement near the end of this manual. Store edger indoors in a dry, high or locked location out of reach of children. Before storing for longer than a few days, always empty the fuel tank. Never store the machine with fuel in the fuel tank inside a building where fumes may reach an open flame or sparks, or in a confined area such as a car trunk. Your power edger is designed to produce sharp contoured borders around lawns and flower-beds. It will cut almost all types of grass, weeds and soft green plants. Preparations If the soil is very dry, spray it with water before you start work: this softens the soil a little and also reduces the amount of dust created. Slightly damp green plants are easier to cut. : Inspect and clear the work area to reduce the risk of injury from thrown objects. : Plan the best route for edging. Always hold and operate your edger on the right-hand side of your body. 241BA000 KN FC 75 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
13
FC 75
English / USA
!
Warning!
A worn or damaged muffler is a fire
hazard and may cause loss of hearing.
Check to see that the muffler is in good
condition. The edger must not be
operated if the muffler is not functioning
properly or has been removed.
Remember that the risk of forest fires is
greater in hot weather.
Use the spark arresting muffler supplied
with the unit. Never touch a hot muffler
or burn will result.
!
Warning!
In order to reduce the risk of fire, do not
modify or remove any part of the muffler
or spark arrestor.
Tighten all nuts, bolts and screws except
the carburetor adjustment screws after
each use.
Keep spark plug and wire connection
tight and clean. The spark plug electrode
gap should be checked with a feeler
gauge at least every 50 operating hours
and reset if necessary. Fit a new spark
plug if the electrodes are badly pitted.
Additionally, the daily maintenance
schedule for your edger set forth in your
STIHL Owner's Manual should be
strictly followed.
For any maintenance please refer to the
maintenance chart
and to the warranty
statement
near the end of this manual.
Store edger indoors in a dry, high or
locked location out of reach of children.
Before storing for longer than a few
days, always empty the fuel tank.
Never store the machine with fuel in the
fuel tank inside a building where fumes
may reach an open flame or sparks, or in
a confined area such as a car trunk.
Your power edger is designed to
produce sharp contoured borders
around lawns and flower-beds. It will cut
almost all types of grass, weeds and soft
green plants.
Preparations
If the soil is very dry, spray it with water
before you start work: this softens the
soil a little and also reduces the amount
of dust created. Slightly damp green
plants are easier to cut.
:
Inspect and clear the work area to
reduce the risk of injury from thrown
objects.
:
Plan the best route for edging.
Always hold and operate your edger
on the right-hand side of your body.
Using the Edger
241BA000 KN