Stihl FS 400 Instruction Manual - Page 9

Starting, Warning, Catalytic converter

Get Stihl FS 400 PDF manuals and user guides View all Stihl FS 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

English / USA Keep the deflector (and the skirt where appropriate) adjusted properly at all times (see chapter on mounting the various cutting tools of your owner's manual). Starting !Warning! Your clearing saw is a one-person machine. Once started, it may fling foreign objects for a great distance. 15m (50ft) To reduce the risk of eye and other injury insure that bystanders are at least 50 feet (15 m) away. Bystanders should be encouraged to wear eye protection. Stop the engine and cutting tool immediately if you are approached. Start and operate your clearing saw without assistance. For specific starting instructions, see the appropriate section of your manual. Place the clearing saw on firm ground or other solid surface in an open area. Maintain a good balance and secure footing. !Warning! To reduce the risk of injury from loss of control, be absolutely sure that the cutting tool is clear of you and all other obstructions and objects, including the ground, because when the engine starts at starting-throttle, engine speed will be fast enough for the clutch to engage and turn the cutting tool. !Warning! When you pull the starter grip, don't wrap the starter rope around your hand. Do not allow the grip to snap back, but guide the starter rope to rewind it properly. Failure to follow this procedure may result in injury to hand or fingers and may damage the starter mechanism. With the engine running but at idle, attach the clearing saw to the spring hook of your harness (see appropriate chapter of this manual). Catalytic converter !Warning! Some STIHL clearing saw models are equipped with a catalytic converter, which is designed to reduce the exhaust emissions of the engine by a chemical process in the muffler. Due to this process, the muffler does not cool down as rapidly as conventional mufflers when the engine returns to idle or is shut off. To reduce the risk of fire and burn injuries, the following specific safety precautions must be observed. !Warning! Since a muffler with a catalytic converter cools down less rapidly than conventional mufflers, always set your clearing saw down in the upright position and never locate it where the muffler is near dry brush, grass, wood chips or other combustible materials while it is still hot. 8 FS 300, FS 350, FS 400, FS 450, FS 480

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
8
English / USA
FS 300, FS 350, FS 400, FS 450, FS 480
Keep the deflector (and the skirt where
appropriate) adjusted properly at all
times (see chapter on mounting the
various cutting tools of your owner's
manual).
Starting
!
Warning!
Your clearing saw is a one-person
machine. Once started, it may fling
foreign objects for a great distance.
To reduce the risk of eye and other injury
insure that bystanders are at least
50 feet (15 m) away. Bystanders should
be encouraged to wear eye protection.
Stop the engine and cutting tool
immediately if you are approached. Start
and operate your clearing saw without
assistance. For specific starting
instructions, see the appropriate section
of your manual. Place the clearing saw
on firm ground or other solid surface in
an open area. Maintain a good balance
and secure footing.
!
Warning!
To reduce the risk of injury from loss of
control, be absolutely sure that the
cutting tool is clear of you and all other
obstructions and objects, including the
ground, because when the engine starts
at starting-throttle, engine speed will be
fast enough for the clutch to engage and
turn the cutting tool.
!
Warning!
When you pull the starter grip, don't
wrap the starter rope around your hand.
Do not allow the grip to snap back, but
guide the starter rope to rewind it
properly. Failure to follow this procedure
may result in injury to hand or fingers
and may damage the starter
mechanism.
With the engine running but at idle,
attach the clearing saw to the spring
hook of your harness (see appropriate
chapter of this manual).
Catalytic converter
!
Warning!
Some STIHL clearing saw
models are equipped with
a catalytic converter,
which is designed to
reduce the exhaust
emissions of the engine
by a chemical process in the muffler.
Due to this process, the muffler does not
cool down as rapidly as conventional
mufflers when the engine returns to idle
or is shut off. To reduce the risk of fire
and burn injuries, the following specific
safety precautions must be observed.
!
Warning!
Since a muffler with a catalytic converter
cools down less rapidly than conven-
tional mufflers, always set your clearing
saw down in the upright position and
never locate it where the muffler is near
dry brush, grass, wood chips or other
combustible materials while it is still hot.
15m (50ft)