Stihl HS 56 C-E Instruction Manual - Page 26

Specifications - 24 hedge trimmer

Get Stihl HS 56 C-E PDF manuals and user guides View all Stihl HS 56 C-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

English Definitions 1 Control Handle The handle of the hedge trimmer held by the rear hand. 2 Throttle Trigger Lockout Must be depressed before the throttle trigger can be activated. 3 Throttle Trigger Controls the speed of the engine. 4 Spark Plug Boot Connects the spark plug with the ignition lead. 5 Muffler with Spark Arresting Screen Muffler reduces exhaust noises and diverts exhaust gases away from operator. Spark arresting screen is designed to reduce the risk of fire. 6 Front Handle Handlebar at the front of hedge trimmer. 7 Fuel Filler Cap For closing the fuel tank. 8 Fuel Tank For fuel and oil mixture. 9 Carburetor Adjusting Screws For tuning the carburetor. 10 Master Control Lever Lever for choke control, starting throttle, run and stop switch position. 11 Fuel Pump Provides additional fuel feed for a cold start. 12 Filter Cover Covers the air filter. 13 Starter Grip The grip of the pull starter, for starting the engine. 14 Blade Scabbard Covers cutting blades when hedge trimmer is not in use. 15 Cutting Blades (HS 46) Steel blades for cutting hedges and shrubs. 16 Cutting Blades (HS 46 C) Steel blades for cutting hedges and shrubs. 17 Cutting Blades (HS 56 C) Steel blades for cutting hedges and shrubs. 18 Blunt Projection (Integral Cutting Blade Guard) Helps to reduce the risk of operator contact by the cutter blade. 19 Cutting Blade Guard Helps to reduce the risk of operator contact by the cutter blade. 20 Guide Guard Protects blades in case of ground or wall contact. Specifications EPA / CEPA The Emission Compliance Period referred to on the Emissions Compliance Label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements. Category A = 300 hours B = 125 hours C = 50 hours Engine STIHL single cylinder two-stroke engine Displacement: Bore: Stroke: Engine power to ISO 7293: Idle speed: Engine cut-off speed: 21.4 cm3 33 mm 25 mm 0.65 kW (0.9 HP) at 8,500 rpm 2,900 rpm 9,300 rpm Ignition System Electronic magneto ignition (breakerless) Spark plug (resistor NGK CMR6H, type): BOSCH USR4AC Electrode gap: 0.5 mm 24 HS 46, HS 46 C, HS 56 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
HS 46, HS 46 C, HS 56 C
English
24
Definitions
1
Control Handle
The handle of the hedge trimmer
held by the rear hand.
2
Throttle Trigger Lockout
Must be depressed before the
throttle trigger can be activated.
3
Throttle Trigger
Controls the speed of the engine.
4
Spark Plug Boot
Connects the spark plug with the
ignition lead.
5
Muffler with Spark Arresting Screen
Muffler reduces exhaust noises and
diverts exhaust gases away from
operator. Spark arresting screen is
designed to reduce the risk of fire.
6
Front Handle
Handlebar at the front of hedge
trimmer.
7
Fuel Filler Cap
For closing the fuel tank.
8
Fuel Tank
For fuel and oil mixture.
9
Carburetor Adjusting Screws
For tuning the carburetor.
10
Master Control Lever
Lever for choke control, starting
throttle, run and stop switch
position.
11
Fuel Pump
Provides additional fuel feed for a
cold start.
12
Filter Cover
Covers the air filter.
13
Starter Grip
The grip of the pull starter, for
starting the engine.
14
Blade Scabbard
Covers cutting blades when hedge
trimmer is not in use.
15
Cutting Blades (HS 46)
Steel blades for cutting hedges and
shrubs.
16
Cutting Blades (HS 46 C)
Steel blades for cutting hedges and
shrubs.
17
Cutting Blades (HS 56 C)
Steel blades for cutting hedges and
shrubs.
18
Blunt Projection (Integral Cutting
Blade Guard)
Helps to reduce the risk of operator
contact by the cutter blade.
19
Cutting Blade Guard
Helps to reduce the risk of operator
contact by the cutter blade.
20
Guide Guard
Protects blades in case of ground or
wall contact.
EPA / CEPA
The Emission Compliance Period
referred to on the Emissions
Compliance Label indicates the number
of operating hours for which the engine
has been shown to meet Federal
emission requirements.
Category
Engine
STIHL single cylinder two-stroke engine
Ignition System
Electronic magneto ignition
(breakerless)
Specifications
A = 300 hours
B = 125 hours
C = 50 hours
Displacement:
21.4 cm
3
Bore:
33 mm
Stroke:
25 mm
Engine power to
ISO 7293:
0.65 kW (0.9 HP)
at 8,500 rpm
Idle speed:
2,900 rpm
Engine cut-off
speed:
9,300 rpm
Spark plug (resistor
type):
NGK CMR6H,
BOSCH USR4AC
Electrode gap:
0.5 mm