Stihl HT Attachment Instruction Manual - Page 17

Cutting Attachment

Get Stihl HT Attachment PDF manuals and user guides View all Stihl HT Attachment manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

0000-GXX-1850-A0 001BA248 KN 001BA244 KN Cutting Attachment Chain scabbard English A 2 A cutting attachment consists of the saw chain, guide bar and chain sprocket. The cutting attachment that comes standard is designed to exactly match the pole pruner. 1 4 3 N Mount the carrying ring (1) at distance A = about 5 cm (2 in) from the control handle (2). N Push the carrying ring (1) over the drive tube. N Insert the M5 nut (3) in the hex recess in the carrying ring. N Fit the M5x14 screw (4). N Line up the carrying ring. N Tighten down the screw firmly. 1 2 a 3 - The pitch (t) of the saw chain (1), chain sprocket and the nose sprocket of the Rollomatic guide bar must match. - The drive link gauge (2) of the saw chain (1) must match the groove width of the guide bar (3). If non-matching components are used, the cutting attachment may be damaged beyond repair after a short period of operation. Your pole pruner comes standard with a chain scabbard that matches the cutting attachment. If you use guide bars of different lenghts on the pole pruner, the length of the chain scabbard must be matched to the guide bar to reduce the risk of injury. It should cover the full length of the guide bar. The length of the matching guide bars is marked on the side of the chain scabbard. HT 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
HT
English
15
N
Mount the carrying ring (1) at
distance A = about 5 cm (2 in) from
the control handle (2).
N
Push the carrying ring (1) over the
drive tube.
N
Insert the M5 nut (3) in the hex
recess in the carrying ring.
N
Fit the M5x14 screw (4).
N
Line up the carrying ring.
N
Tighten down the screw firmly.
A cutting attachment consists of the saw
chain, guide bar and chain sprocket.
The cutting attachment that comes
standard is designed to exactly match
the pole pruner.
–
The pitch (t) of the saw chain (1),
chain sprocket and the nose
sprocket of the Rollomatic guide bar
must match.
–
The drive link gauge (2) of the saw
chain (1) must match the groove
width of the guide bar (3).
If non-matching components are used,
the cutting attachment may be damaged
beyond repair after a short period of
operation.
Chain scabbard
Your pole pruner comes standard with a
chain scabbard that matches the cutting
attachment.
If you use guide bars of different lenghts
on the pole pruner, the length of the
chain scabbard must be matched to the
guide bar to reduce the risk of injury. It
should cover the full length of the guide
bar.
The length of the matching guide bars is
marked on the side of the chain
scabbard.
A
1
2
3
4
0000-GXX-1850-A0
Cutting Attachment
001BA248 KN
1
2
3
a
001BA244 KN