Stihl MS 440 Product Instruction Manual - Page 17

Warning, Low kickback saw chain and reduced, kickback bars, Maintenance, Repair and Storing

Get Stihl MS 440 PDF manuals and user guides View all Stihl MS 440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

English / USA When a kickback occurs, the guide bar may rotate around the front handle. If the cutting position is such that the operator's left hand is gripping the front handle behind the hand guard, and if the left hand rotates around the front handle and makes a sufficiently forceful contact with the front hand guard, which is the Quickstop activating lever, this contact will activate the Quickstop. The chain brake on most new model STIHL chainsaws can also be activated by inertia. See the chapter entitled "Chain Brake" of your Owner's Manual. 001BA036 KN !Warning! Never operate your chainsaw without a front hand guard. In a kickback situation this guard helps protect your left hand or other parts of your body. In addition, removal of the hand guard on a saw equipped with a chain brake will deactivate the chain brake. !Warning! No Quickstop or other chain brake device prevents kickback. These devices are designed to reduce the risk of kickback injury, if activated, in certain kickback situations. In order for the Quickstop to reduce the risk of kickback injury, it must be properly maintained and in good working order. See the chapter entitled "Chain Brake" and "Maintenance, Repair and Storing" of your Owner's Manual. In addition, there must be enough distance between the bar and the operator to ensure that the Quickstop has sufficient time to activate and stop the chain before potential contact with the operator. !Warning! An improperly maintained chain brake may increase the time needed to stop the chain after activation, or may not activate at all. !Warning! Never run the chainsaw above idle speed for more than 3 seconds when the chain brake is engaged or the chain is pinched or otherwise caught in the cut. Clutch slippage can cause excessive heat, leading to severe damage of the motor housing, clutch and oiler component and may interfere with the operation of the chain brake. If clutch slippage in excess of 3 seconds has occurred, allow the motor housing to cool before proceeding and check the operation of your chain brake as described in the chapter entitled "Chain Brake". Also make sure that the chain is not turning at idle speed (see above "Important Adjustments"). Low kickback saw chain and reduced kickback bars STIHL offers a variety of bars and chains. STIHL reduced kickback bars and low kickback chains are designed to 16 MS 440, MS 440 W, MS 440 C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
16
English / USA
MS 440, MS 440 W, MS 440 C
When a kickback occurs, the guide bar
may rotate around the front handle. If the
cutting position is such that the
operator's left hand is gripping the front
handle behind the hand guard, and if the
left hand rotates around the front handle
and makes a sufficiently forceful contact
with the front hand guard, which is the
Quickstop activating lever, this contact
will activate the Quickstop. The chain
brake on most new model STIHL
chainsaws can also be activated by
inertia. See the chapter entitled "Chain
Brake" of your Owner's Manual.
!
Warning!
Never operate your chainsaw without a
front hand guard. In a kickback situation
this guard helps protect your left hand or
other parts of your body. In addition,
removal of the hand guard on a saw
equipped with a chain brake will
deactivate the chain brake.
!
Warning!
No Quickstop or other chain brake
device prevents kickback. These
devices are designed to reduce the risk
of kickback injury, if activated, in certain
kickback situations. In order for the
Quickstop to reduce the risk of kickback
injury, it must be properly maintained
and in good working order. See the
chapter entitled "Chain Brake" and
"Maintenance, Repair and Storing" of
your Owner's Manual. In addition, there
must be enough distance between the
bar and the operator to ensure that the
Quickstop has sufficient time to activate
and stop the chain before potential
contact with the operator.
!
Warning!
An improperly maintained chain brake
may increase the time needed to stop
the chain after activation, or may not
activate at all.
!
Warning!
Never run the chainsaw above idle
speed for more than 3 seconds when the
chain brake is engaged or the chain is
pinched or otherwise caught in the cut.
Clutch slippage can cause excessive
heat, leading to severe damage of the
motor housing, clutch and oiler
component and may interfere with the
operation of the chain brake. If clutch
slippage in excess of 3 seconds has
occurred, allow the motor housing to
cool before proceeding and check the
operation of your chain brake as
described in the chapter entitled "Chain
Brake". Also make sure that the chain is
not turning at idle speed (see above
"Important Adjustments").
Low kickback saw chain and reduced
kickback bars
STIHL offers a variety of bars and
chains. STIHL reduced kickback bars
and low kickback chains are designed to
001BA036 KN