Home » Stihl Manuals » Tools » Stihl MSA 120 C-B » Manual Viewer

Stihl MSA 120 C-B Instruction Manual - Page 38

Charging the Battery

Get Stihl MSA 120 C-B PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

English 13 Charging the Battery 13.1 Setting up the Charger WARNING Read and follow the battery and charger safety precautions and instructions in this manual, @ 9 and @ 10. To reduce the risk of short circuit, which could lead to electric shock, fire and explosion, make sure the charger and its components are dry and not damaged; operate the charger indoors at an appropriate ambient temperature, @ 10. WARNING Since the battery and charger heat up during the charging process, do not operate the charger on a combustible surface or in a location where combustible gases, liquids, vapors, dusts or other materials and substances are present, @ 10. To set up the charger: 13 Charging the Battery ► Position the power supply cord (2) so that it will not be stepped on, tripped over, come in contact with sharp objects or moving parts or otherwise present a tripping hazard or be subjected to damage or stress. 13.2 Charging WARNING STIHL batteries contain safety features and devices which, if damaged, may allow the battery to generate heat, rupture, leak, ignite or explode. Never charge a malfunctioning, damaged, cracked, leaking or deformed battery. For indoor use only. Keep the charger dry. Protect it from rain, water, liquids and damp conditions. Never insert a wet battery. Never use a wet charger, @ 10. To charge the battery: 3 2 0000-GXX-0636-A1 0000-GXX-0637-A0 4 3 2 1 2 ► Insert the plug (3) into a properly installed wall outlet (4) matching the voltage and electrical frequency stated on the rating plate on the charger. The charger runs a self-test immediately after it is plugged in. The charger LED (1) will glow green for about 1 second, then it will glow red briefly before going out. Once the LED goes out, the self-test is complete and the charger is ready to charge the battery. 4 1 ► Push the battery (2) into the charger (3) until it stops. The LED on the charger (4) glows green when the battery is charging. The LEDs (1) on the battery glow green and show the state of charge. When the LEDs on the battery turn off, the charging process is complete and the charger will shut itself off. ► Remove the battery from the charger and disconnect the power supply cord from the electrical outlet when charging is complete. 36 0458-716-8621-E

Section	Page
1 Introduction	5
2 Guide to Using this Manual	5
2.1 Signal Words	5
2.2 Symbols in Text	5
3 Main Parts	6
3.1 Chain Saw, Battery and Charger	6
4 Safety Symbols on the Products	7
4.1 Chain Saw, Battery and Charger	7
5 General Power Tool Safety Warnings	8
5.1 Introduction	8
5.2 Work Area Safety	8
5.3 Electrical Safety	8
5.4 Personal Safety	8
5.5 Power Tool Use and Care	9
5.6 Battery Tool Use and Care	9
5.7 Service	10
5.8 General Chain Saw Safety Warnings	10
5.9 Causes and Operator Prevention of Kickback	11
6 IMPORTANT SAFETY INSTRUCTIONS	11
6.1 Intended Use	11
6.2 Operator	12
6.3 Personal Protective Equipment	13
6.4 Chain Saw	14
6.5 Using the Chain Saw	15
6.5.1 Before Operation	15
6.5.2 Holding and Controlling the Chain Saw	16
6.5.3 Working Conditions	18
6.5.4 Operating Instructions	19
7 Kickback and Other Reactive Forces	20
7.1 Reactive Forces	20
7.2 Kickback	21
7.2.1 Kickback	21
7.2.2 Chain Saw Kickback Standards	21
7.2.3 Devices for Reducing the Risk of Kickback Injury	22
7.2.4 To Avoid Kickback	25
7.3 Pull-in	25
7.4 Pushback	26
8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling	26
8.1 Intended Uses	26
8.2 Bucking	26
8.3 Limbing	27
8.4 Pruning	28
8.5 Cutting Logs Under Tension	29
8.6 Felling	30
8.6.1 Felling Conditions	30
8.6.2 Escape Path	31
8.6.3 Conventional Notch	31
8.6.4 Open-faced Notch	31
8.6.5 Sapwood Cuts	32
8.6.6 Felling Back Cut	32
8.6.7 Fan Cut	33
9 Battery Safety	33
9.1 Warnings and Instructions	33
10 Charger Safety	35
10.1 Warnings and Instructions	35
11 Maintenance, Repair and Storage	36
11.1 Warnings and Instructions	36
12 Before Starting Work	37
12.1 Preparing the Chain Saw for Operation	37
13 Charging the Battery	38
13.1 Setting up the Charger	38
13.2 Charging	38
13.3 Mounting the Charger on a Wall	39
14 LED Diagnostics	39
14.1 LEDs on the Battery	39
14.1.1 Battery Status	39
14.1.2 Chain Saw Status	39
14.1.3 Charge Status	40
14.2 LED on the Charger	40
15 Assembling the Chain Saw	40
15.1 Cutting Attachment	40
15.2 Mounting and Removing the Guide Bar and Saw Chain	41
15.2.1 Mounting the Guide Bar and Chain	41
15.2.2 Removing the Guide Bar and Chain	42
15.3 Tensioning the Saw Chain	42
15.4 Lubricating the Saw Chain and Guide Bar	43
15.4.1 Bar and Chain Lubricant	43
15.4.2 Filling the Chain Oil Tank	43
16 The Chain Brake	44
16.1 Engaging the Chain Brake	44
16.2 Disengaging the Chain Brake	45
16.3 Maintaining the Chain Brake	45
17 Inserting and Removing the Battery	45
17.1 Inserting the Battery	45
17.2 Removing the Battery	46
18 Switching the Chain Saw On and Off	46
18.1 Switching On	46
18.2 Switching Off	47
19 Checking the Chain Saw	47
19.1 Checking the Operation of the Chain Brake	47
19.2 Testing the Controls	48
19.3 Testing Saw Chain Lubrication	48
20 After Finishing Work	49
20.1 Preparing for Transportation or Storage	49
21 Transporting the Chain Saw and Battery	49
21.1 Chain Saw	49
21.2 Battery	49
22 Storing the Chain Saw, Battery and Charger	50
22.1 Chain Saw	50
22.2 Battery	50
22.3 Charger	51
23 Cleaning	51
23.1 Cleaning the Chain Saw, Battery and Charger	51
23.2 Cleaning the Guide Bar and Saw Chain	51
24 Inspection and Maintenance	52
24.1 Inspecting and Maintaining the Chain Saw	52
24.2 Inspecting and Maintaining the Chain Sprocket	52
24.3 Inspecting and Maintaining the Guide Bar	53
24.4 Inspecting, Maintaining and Sharpening the Saw Chain	53
25 Troubleshooting Guide	57
25.1 Chain Saw and Battery	57
25.2 Charger	58
26 Specifications	59
26.1 STIHL MSA 120 C, MSA 140 C	59
26.2 Chain Sprockets	59
26.3 Minimum Groove Depth of Guide Bars	59
26.4 Depth Gauge Setting	59
26.5 STIHL AK Series Battery	59
26.6 STIHL AL 101	59
26.7 Symbols on the Chain Saw, Battery and Charger	60
26.8 Engineering Improvements	60
26.9 FCC 15 Compliance Statement	60
27 Combinations of Guide Bars and Saw Chains	62
27.1 STIHL MSA 120 C, MSA 140 C	62
28 Replacement Parts and Equipment	63
28.1 Genuine STIHL Replacement Parts	63
29 Disposal	63
29.1 Disposal of the Chain Saw and Charger	63
29.2 Battery Recycling	63
30 Limited Warranty	63
30.1 STIHL Incorporated Limited Warranty Policy	63
31 Trademarks	63
31.1 Registered Trademarks	63
31.2 Common Law Trademarks	64
32 Addresses	64
32.1 STIHL Incorporated	64
1 Introducción	67
2 Acerca de este manual de instrucciones	67
2.1 Palabras identificadoras	67
2.2 Símbolos en el texto	67
3 Componentes importantes	68
3.1 Motosierra, batería y cargador	68
4 Símbolos de seguridad en los productos	69
4.1 Motosierra, batería y cargador	69
5 Advertencias generales de seguridad para herramientas motorizadas	70
5.1 Introducción	70
5.2 Seguridad en la zona de trabajo	70
5.3 Seguridad eléctrica	70
5.4 Seguridad personal	71
5.5 Uso y cuidado de la herramienta eléctrica	71
5.6 Uso y cuidado de la herramienta de baterías	72
5.7 Mantenimiento	72
5.8 Advertencias de seguridad generales para motosierras	72
5.9 Causas del contragolpe y medidas de prevención	73
6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD	74
6.1 Uso previsto	74
6.2 Operador	75
6.3 Equipos de protección personal	76
6.4 Motosierra	77
6.5 Uso de la motosierra	78
6.5.1 Antes del uso	78
6.5.2 Sujeción y control de la motosierra	80
6.5.3 Condiciones de trabajo	82
6.5.4 Instrucciones de manejo	83
7 Contragolpe y otras fuerzas reactivas	84
7.1 Fuerzas reactivas	84
7.2 Contragolpe	85
7.2.1 Contragolpe	85
7.2.2 Normas para el contragolpe de las motosierras	85
7.2.3 Dispositivos para reducir el riesgo de lesiones por contragolpe	86
7.2.4 Para evitar el contragolpe	89
7.3 Tirones	90
7.4 Rechazo	90
8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos	91
8.1 Usos previstos	91
8.2 Tronzado	91
8.3 Desrame	92
8.4 Poda	93
8.5 Corte de troncos bajo tensión	94
8.6 Tala	94
8.6.1 Condiciones de tala	94
8.6.2 Ruta de escape	95
8.6.3 Entalla convencional	96
8.6.4 Entalla de cara libre	96
8.6.5 Cortes de albura	97
8.6.6 Corte trasero de tala	97
8.6.7 Corte en abanico	98
9 Seguridad de la batería	98
9.1 Advertencias e instrucciones	98
10 Seguridad del cargador	100
10.1 Advertencias e instrucciones	100
11 Mantenimiento, reparación y almacenamiento	101
11.1 Advertencias e instrucciones	101
12 Antes de empezar a trabajar	103
12.1 Preparación de la motosierra para el funcionamiento:	103
13 Carga de la batería	103
13.1 Preparación del cargador para el funcionamiento	103
13.2 Carga	103
13.3 Montaje del cargador en pared	104
14 Diagnóstico de LED	105
14.1 LED en la batería	105
14.1.1 Estado de la batería	105
14.1.2 Estado de la motosierra	105
14.1.3 Estado de carga	105
14.2 LED en el cargador	105
15 Armado de la motosierra	106
15.1 Accesorio de corte	106
15.2 Montaje y extracción de la espada y la cadena de aserrado	106
15.2.1 Montaje de la espada y la cadena	106
15.2.2 Retiro de la espada y la cadena	108
15.3 Tensado de la cadena de aserrado	108
15.4 Lubricación de la cadena de aserrado y de la espada	109
15.4.1 Lubricante de espadas y cadenas	109
15.4.2 Llenado del tanque de aceite de la cadena	109
16 El freno de cadena	110
16.1 Accionamiento del freno de la cadena	110
16.2 Cómo soltar el freno de la cadena	111
16.3 Mantenimiento del freno de la cadena	111
17 Colocación y extracción de la batería.	111
17.1 Colocación de la batería	111
17.2 Extracción de la batería	112
18 Encendido y apagado de la motosierra	112
18.1 Encendido	112
18.2 Apagado	113
19 Revisión de la motosierra	113
19.1 Control del funcionamiento del freno de la cadena	113
19.2 Prueba de los controles	114
19.3 Prueba de la lubricación de la cadena de aserrado	114
20 Después de completar el trabajo	115
20.1 Preparación para el transporte o el almacenamiento	115
21 Transporte de la motosierra y de la batería	115
21.1 Motosierra	115
21.2 Batería	116
22 Almacenamiento de la motosierra, de la batería y del cargador	116
22.1 Motosierra	116
22.2 Batería	116
22.3 Cargador	117
23 Limpieza	117
23.1 Limpieza de la motosierra, de la batería y del cargador	117
23.2 Limpieza de la espada y la cadena de aserrado	118
24 Inspección y mantenimiento	118
24.1 Inspección y mantenimiento de la motosierra	118
24.2 Revisión y mantenimiento del piñón de cadena	119
24.3 Inspección y mantenimiento de la espada	119
24.4 Inspección, mantenimiento y afilado de la cadena de aserrado	120
25 Guía de solución de problemas	124
25.1 Motosierra y batería	124
25.2 Cargador	125
26 Especificaciones	126
26.1 STIHL MSA 120 C, MSA 140 C	126
26.2 Piñones de cadena	126
26.3 Profundidad de ranura mínima para las espadas	126
26.4 Ajuste de calibrador de profundidad	126
26.5 Batería STIHL serie AK	126
26.6 STIHL AL 101	127
26.7 Símbolos de la motosierra, de la batería y del cargador	127
26.8 Mejoramientos técnicos	127
26.9 Declaración de cumplimiento con norma FCC 15	128
27 Combinaciones de espadas y cadenas de aserrado	129
27.1 STIHL MSA 120 C, MSA 140 C	129
28 Piezas y equipos de repuesto	130
28.1 Piezas de repuesto originales de STIHL	130
29 Eliminación	130
29.1 Desecho de la motosierra y del cargador	130
29.2 Reciclado de las baterías	130
30 Garantía limitada	130
30.1 Política de garantía limitada de STIHL Incorporated	130
31 Marcas comerciales	131
31.1 Marcas comerciales registradas	131
31.2 Marcas comerciales por ley común	131
32 Direcciones	131

Match case Limit results 1 per page

0458-716-8621-E

English

13 Charging the Battery

13.1

Setting up the Charger

WARNING

Read and follow the battery and charger safety precautions

and instructions in this manual,

9 and

10. To reduce

the risk of short circuit, which could lead to electric shock,

fire and explosion, make sure the charger and its

components are dry and not damaged; operate the charger

indoors at an appropriate ambient temperature,

10.

WARNING

Since the battery and charger heat up during the charging

process, do not operate the charger on a combustible

surface or in a location where combustible gases, liquids,

vapors, dusts or other materials and substances are

present,

10.

To set up the charger:

►

Insert the plug (3) into a properly installed wall outlet (4)

matching the voltage and electrical frequency stated on

the rating plate on the charger.

The charger runs a self-test immediately after it is plugged

in. The charger LED (1) will glow green for about 1 second,

then it will glow red briefly before going out. Once the LED

goes out, the self-test is complete and the charger is ready

to charge the battery.

►

Position the power supply cord (2) so that it will not be

stepped on, tripped over, come in contact with sharp

objects or moving parts or otherwise present a tripping

hazard or be subjected to damage or stress.

13.2

Charging

WARNING

STIHL batteries contain safety features and devices which,

if damaged, may allow the battery to generate heat, rupture,

leak, ignite or explode. Never charge a malfunctioning,

damaged, cracked, leaking or deformed battery. For indoor

use only. Keep the charger dry. Protect it from rain, water,

liquids and damp conditions. Never insert a wet battery.

Never use a wet charger,

10.

To charge the battery:

►

Push the battery (2) into the charger (3) until it stops.

The LED on the charger

(4) glows green when the battery

is charging.

The LEDs (1) on the battery glow green and show the

state of charge.

When the LEDs on the battery turn off, the charging

process is complete and the charger will shut itself off.

►

Remove the battery from the charger and disconnect the

power supply cord from the electrical outlet when charging

is complete.

Charging the Battery

0000-GXX-0636-A1

0000-GXX-0637-A0