TASCAM 414mkII Owners Manual - Page 12

Recorder Controls, Connections on the Rear Panel - studio 414 mkii

Get TASCAM 414mkII PDF manuals and user guides View all TASCAM 414mkII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

PORTASTUDIO 414 MKII Brief Guide Recorder Controls Meters : The meters numbered 1-4 show the playback or the record level of the respective tape tracks. The average record level should be in the center (0), but occasional peaks up to +6 are acceptable. ZERO RETURN : When this switch is on and you press REW, the tape fast winds to the counter zero point. The associated LED blinks when the tape is rewinding, and glows solid when the 000 point is reached. DBX switch : Normally, leave this switch at ON. When you use track 4 to record and play back MIDI sync tones or time code, set to SYNC then the dbx is on for tracks 1-3, and off on track 4. Tape counter : Shows the distance the tape has moved from a zero reference point. Counter reset button : Press to change the counter to "000". PITCH CONTROL : Increases or decreases the speed of the transport in Play and also in Record, over a 10% range (approx.). Connections on the Rear Panel SUB IN L and R : Provide a direct route to the MASTER fader. An outboard mixer may be connected here. The SUB IN R jack is also used to record sync tones on track 4. SYNC OUT : Sync tones you'll record on track 4 are sent out of this jack to the TASCAM MTS-30 MIDI/Tape synchronizer or other similar units. LINE OUT L and R : Normally, connect these jacks to the Left and Right inputs of your mixdown deck. MON OUT L and R : These are connected to an amplifier powering the control room speakers. EFFECT 1 SEND : For sending post channel fader signals to effects devices. The returns are plugged into the STEREO INPUTS. EFFECT 2 SEND/TAPE CUE OUT : The signal available at this jack comes either from post channel fader for connection to an additional effects device or from the tape for connection to a studio speaker system, as selected by means of the EFFECT 2/TAPE CUE switch. Transport keys : Principally these work the same as on any cassette recorder. RECORD FUNCTION 1-4 : Used to select tracks to record on, and also recording sources (channels or stereo busses). 13 On the front PHONES : This carries the same mix as the MON OUT jacks, as selected by the MONITOR switches. REMOTE PUNCH IN/OUT : Connect to this jack the optional RC- 30P footswitch. 14 ✂

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
13
14
PORTASTUDIO 414 MKII Brief Guide
DBX switch :
Normally, leave this switch at
ON. When you use track 4 to record and
play back MIDI sync tones or time code,
set to SYNC then the dbx is on for tracks
1-3, and off on track 4.
Tape counter :
Shows the distance the tape
has moved from a zero reference point.
Counter reset button :
Press to change the
counter to "000".
PITCH CONTROL :
Increases or decreases
the speed of the transport in Play and
also in Record, over a 10% range
(approx.).
Meters :
The meters numbered 1-4 show the
playback or the record level of the
respective tape tracks. The average
record level should be in the center (0),
but occasional peaks up to +6 are
acceptable.
ZERO RETURN :
When this switch is on and
you press REW, the tape fast winds to
the counter zero point. The associated
LED blinks when the tape is rewinding,
and glows solid when the 000 point is
reached.
Recorder Controls
Transport keys :
Principally these work the same as on any
cassette recorder.
RECORD FUNCTION 1-4 :
Used to select tracks
to record on, and also recording sources
(channels or stereo busses).
SUB IN L and R :
Provide a direct route to
the MASTER fader. An outboard mixer
may be connected here. The SUB IN R
jack is also used to record sync tones
on track 4.
SYNC OUT :
Sync tones you'll record on
track 4 are sent out of this jack to the
TASCAM MTS-30 MIDI/Tape synchro-
nizer or other similar units.
LINE OUT L and R :
Normally, connect
these jacks to the Left and Right inputs
of your mixdown deck.
MON OUT L and R :
These are connected
to an amplifier powering the control
room speakers.
EFFECT 1 SEND :
For sending post chan-
nel fader signals to effects devices. The
returns are plugged into the STEREO
INPUTS.
EFFECT 2 SEND/TAPE CUE OUT :
The
signal available at this jack comes either
from post channel fader for connection
to an additional effects device or from
the tape for connection to a studio
speaker system, as selected by means
of the EFFECT 2/TAPE CUE switch.
PHONES :
This carries the same mix as the MON OUT jacks,
as selected by the MONITOR switches.
REMOTE PUNCH IN/OUT :
Connect to this jack the optional
RC- 30P footswitch.
Connections on the Rear Panel
On the fr
ont
✂