TASCAM SS-R200 SS-CDR200 RS-232C documentation
TASCAM SS-R200 Manual
View all TASCAM SS-R200 manuals
Add to My Manuals
Save this manual to your list of manuals |
TASCAM SS-R200 manual content summary:
- TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 1
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 TASCAM SS-CDR200/SS-R200 CONTROL I/O Terminals RS-232C Protocol Specifications TEAC Corporation - 1 - - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 2
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ATTENTION TEAC Corporation ("TEAC") licenses you " the protocol for the purpose of developing devices (including software) compatible with applicable TASCAM products. 3. Your receipt of this document does not mean that you are given any - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 3
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 1. Overview The SS-CDR200/SS-R200 ("controlled device") can be controlled from an external device ("external controller"), such as a computer, through a serial RS-232C connection. 2. Specifications 2.1. Electrical Specifications - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 4
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 2.3. Connector pin-out Connector D-sub 9pin female (Inch screw thread) Terminal short-circuited to receive or transmit RTS/CTS signals. RXD 2 TXD 3 GND 5 7 8 Controlled device (SS-CDR200/SS-R200) RXD TXD GND External controller - 4 - - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 5
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 3. Command Format 3.1. Command Format Overview The command format is as follows. Byte 1 Byte 2 Byte 3 Byte 4 Byte 5 Byte 6 Byte 7 Byte 8 ... Byte n LF ID Command Data 1 - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 6
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 3.3. Command Sequence In most cases, the controlled device does not send an ACK command in response to a transport control command or data preset command - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 7
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 Example 4: Performing the next operation after checking the status of the controlled device When switching from one mode to another, the controlled device sends - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 8
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 3.4. List of Commands Control/Preset/Sense Command 0F INFORMATION REQUEST 10 STOP 12 PLAY 13 RECORD 14 READY 16 SHUTTLE 17 FLASH LOAD 18 - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 9
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 Command Details ・INFORMATION REQUEST INFORMATION REQUEST requests the controlled device to return information including the software version of the controlled device. Command Data Return - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 10
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・SHUTTLE SHUTTLE puts the controlled device into 97] ・EJECT EJECT ejects a CD Media from the controlled device. (If the controlled device is SS-R200, it returns ILLEGAL [F2].) If the device selected on the controlled device is not CD, - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 11
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CALL CALL locates the controlled device to a call point and puts the controlled device into the ready state. Command Data Return 1D None None ・ - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 12
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・AUTO TRACK LEVEL PRESET AUTO TRACK LEVEL PRESET sets the auto track level of the controlled device. Only when this command is sent with - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 13
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・PITCH CONTROL DATA PRESET PITCH CONTROL DATA PRESET sets the pitch of playback of the controlled device. (%) The setting range is ±16.0%. Only when - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 14
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CLOCK DATA PRESET CLOCK DATA PRESET sets the date and time information for the controlled device. Only when this command is sent with request - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 15
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・TIME SEARCH PRESET TIME SEARCH PRESET performs a search on the controlled device by specifying a track number and time. If the controlled device receives this - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 16
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・AUTO CUE SELECT AUTO CUE SELECT turns the Auto-cue mode of the controlled device on or off. Only when this command is sent - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 17
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・EOM TRACK TIME PRESET EOM TRACK TIME PRESET sets the EOM (end-of-track-warning) time in seconds. Only when this command is sent - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 18
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・AUTO READY SELECT AUTO READY SELECT turns the auto ready mode of the controlled device on or off. Only when this command is sent - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 19
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・INCR PLAY SELECT INCR PLAY SELECT turns the incremental playback mode of the controlled device on or off. Only when this command is sent - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 20
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・PLAY MODE SENSE PLAY MODE SENSE requests the controlled device to return the current playback mode setting of the controlled device. Command Data Return - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 21
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CURRENT TRACK TIME SENSE CURRENT TRACK TIME SENSE requests the controlled device to return the selected time information about the current track or the - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 22
. Command: Data: Return: 79 None CAUTION SENSE RETURN [F9] ・VENDER COMMAND VENDER COMMAND is a command which controls a function available only for SS-CDR200/SS-R200. The function is identified with the value of Data1 and Data2. Command: 7F Data: -- bytes Return: VENDER COMMAND RETURN [FF - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 23
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・INFORMATION RETURN INFORMATION RETURN is sent in response to the INFORMATION REQUEST command [0F] to show the software version. Command 8F Data 4 bytes Request - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 24
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・AUTO TRACK LEVEL RETURN AUTO TRACK LEVEL RETURN is sent in response to the AUTO TRACK LEVEL PRESET command [21] to show the current - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 25
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CLOCK DATA RETURN CLOCK DATA RETURN is sent in response to the CLOCK DATA PRESET command [27] to show the current date and time - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 26
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・AUTO CUE SELECT RETURN AUTO CUE SELECT RETURN is sent in response to the AUTO CUE SELECT command [30] to show the current Auto - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 27
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・PITCH CONTROL SELECT RETURN PITCH CONTROL SELECT RETURN is sent in response to the PITCH CONTROL SELECT command [35] to show the current pitch - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 28
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・INCR PLAY SELECT RETURN INCR PLAY SELECT RETURN is sent in response to the INCR PLAY SELECT command [3A] to show the current incremental - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 29
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・PLAY MODE RETURN PLAY MODE RETURN is sent in response to the PLAY MODE SENSE command [4E] to show the current playback mode setting. - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 30
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・MEDIA STATUS RETURN MEDIA STATUS RETURN is sent in response to the MEDIA STATUS SENSE command [56] to show the presence or absence of a - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 31
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CURRENT TRACK TIME RETURN CURRENT TRACK TIME RETURN is sent in response to the CURRENT TRACK TIME SENSE command [58] to show the selected - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 32
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・TOTAL TRACK No./TOTAL TIME RETURN TOTAL TRACK No./TOTAL TIME RETURN is sent in response to the TOTAL TRACK No./TOTAL TIME SENSE - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 33
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・KEYBOARD TYPE RETURN KEYBOARD TYPE RETURN is sent in response to the KEYBOARD TYPE SENSE command [5F] to show the current keyboard type setting. - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 34
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CHANGE STATUS CHANGE STATUS is sent from the controlled device to the external controller to show that the controlled device has switched from one - TASCAM SS-R200 | SS-CDR200 RS-232C documentation - Page 35
RS-232C Protocol Specifications Rev. 1.00 SS-CDR200/SS-R200 ・CAUTION SENSE RETURN CAUTION SENSE RETURN is sent in response to the CAUTION SENSE command [79]. Command Data Request command Data 1 N2 Data 2 N3
RS-232C Protocol Specifications Rev. 1.00
SS-CDR200/SS-R200
- 1 -
TASCAM SS-CDR200
/
SS-R200
CONTROL I/O Terminals
RS-232C Protocol Specifications
TEAC Corporation